y0760 BigScale Rallye-Cross tires Typ 450 for FG and other, 2 pair/4 pcs. for 18mm square
€79.90
Available
Product information "y0760 BigScale Rallye-Cross tires Typ 450 for FG and other, 2 pair/4 pcs. for 18mm square"
Glued on robust 6-spoke star wheels, with 6 ribbed reinforcement bars.
With 18 mm wheel square, suitable for most 1:5 / 1:6 RC cars, FG, Carson, etc.
Lane widening with 23 mm countersunk nut and 14 mm deep square drive for most models.
450 block sections 3.5 mm thick, provide a good grip, even on hard or slippery surfaces.
Due to the high-strength 14 mm tire shoulder, the cornering power of the Rallye-Cross 450 is high, despite the high profile of 3.5 mm, but without provoking a disproportionate overdrive of the model.
The large inner diameter of 114 mm the rim, as well as the position of the wheel allows on nearly all models to eventually mount a disc brake at the front, as well as rear wheels. The dimension of the inside edge of the rim to the wheel is 20 mm. The 18 mm, 6-braced wheel square of the Rallye-Cross 450 rim is 8 mm deep.
Measures of the Rallye-Cross 450 wheel/rim:
- Outside diameter: 162 mm
- Profile width: 62 mm
- Rim inside: 114 mm
- Tire shoulder: 14 mm
- Block profile: 3,5 mm
| Also suitable for: | |
 |  |
| With the following wheel adapter: y1183 Rim adapter | With the following wheel adapter: y0786 Rim adapter |
Login
Customers also viewed
Mammoth Supergrip onroad 60 and 80 mm tires on white FG rims complete glued, 1 pair.Mammoth Supergrip onroad tires on FG rims for 1/6 and 1/5 offroad cars.Suitable for asphalt surfaces such as car parks and race tracks. Racing tyres for your off-road model.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmGlued on genuine FG rims (rear tires using extension rings outside ), with foam rubber inserts included. Rim has 18 mm square drive with reinforcement ring.Please note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tirey0581y0582y0583y0584Rear tirey0591y0592y0593y0594General recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Prices per unit: FrontRearMammoth Supergrip:Pair44,90 EUR49,90 EURTire inserts:Pair13,00 EUR13,00 EURFG rim:Pair14,90 EUR14,90 EURFG extension ring:Pair--.-- EUR14,90 EURMounting:Pair13,00 EUR13,00 EURPrices Total 85,80 EUR 105,70 EUR
The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. - TT1040 Top Tuning wheel hub 24mm/6-edge for Losi Super BajaRey/2.0 and Super Rock Rey for plastic axle stubs. - AT-004 Atop wheel nuts 4 pieces Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.
Genuine Carson spare/option part. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Rim with 18 mm square drive.outer diameter 163 mmContents:2 pieces
Item N° 67214/05 Mini block M / OR tires, glued, white, 2pcs.Completely new revised and in important details improved Mini Block Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant.The FG Mini Block tires are especially well-suited for slightly loose and humid ground. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle. The Mini Block tires are also well-suited as front tires for 2WD models in combination with the Mini Pin tires on the rear axle. The tires are ready glued on the new Leo 1:6 wheels. For the assembly you need the 12mm square wheel drivers (ItemN°. 06107/07).The glued tires are not suitable for the FG models Marder, Beetle, Off-Road Buggy and Monster models.
Genuine FG spare/option part.Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Measures:Diameter: 145 mmWidth: 80 mmRim with 18 mm square drive.