y0658 Narrow-Grip 462 type tires for Losi, HPI, FG, Carson and Co., 18 mm square drive

Complete set of four CRT stadium tires and rims, mounted and glued with tire inserts. Fits FG and Carson 1/6 scale cars.Tire diameter 170 mm, tire width 80 mm, 18 mm wheel square. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Also suitable for:With the following wheel adapter: y1183 Rim adapter

Glued on robust 6-spoke star wheels, with 6 ribbed reinforcement bars.With 18 mm wheel square, suitable for most 1:5 / 1:6 RC cars, FG, Carson, etc.Lane widening with 23 mm countersunk nut and 14 mm deep square drive for most models.450 block sections 3.5 mm thick, provide a good grip, even on hard or slippery surfaces.Due to the high-strength 14 mm tire shoulder, the cornering power of the Rallye-Cross 450 is high, despite the high profile of 3.5 mm, but without provoking a disproportionate overdrive of the model.The large inner diameter of 114 mm the rim, as well as the position of the wheel allows on nearly all models to eventually mount a disc brake at the front, as well as rear wheels. The dimension of the inside edge of the rim to the wheel is 20 mm. The 18 mm, 6-braced wheel square of the Rallye-Cross 450 rim is 8 mm deep.Measures of the Rallye-Cross 450 wheel/rim:Outside diameter: 162 mmProfile width: 62 mmRim inside: 114 mmTire shoulder: 14 mmBlock profile: 3,5 mmAlso suitable for:With the following wheel adapter: y1183 Rim adapterWith the following wheel adapter: y0786 Rim adapter

Off-road tires for sandy underground! Gives great results on those carpets which are typical for some off-road tracks. 462 grippy square studs per tire, a total of more then 1800 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability! Therefore the car is less prone to undesirable side rolls! The rim is the 6-spoke design with a steel reinforcement ring around the wheel drive. The NARROW-GRIP tires are available  with 24mm hex for Losi, HPI Baja 5 and Carson GP Wild Attack series cars and they allready glued!To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with hex drive and completely mounted via tightening the wheel nut! Dimensions:Outer tire diameter: 175 mmTire and rim width: 62 mmRim inner diameter: 119 mmWeight for one tire: 375 grams / for a pair: 750 gramshe manufacturer of the Narrow-Grip 462 indicates that the use of these tires on very heavy models, like the Losi 5ive-T under heavy conditions, such as jumps and shifting / tilting of the chassis, may lead to breakage of spokes or hex socket. Due to this notice that kind of failure will not be compensated. We apologize for this note!As an alternative, we recommend our special offer for the Losi 5ive-T OEM tires and in particular all tire combinations with MadMax EXTREME rims or for Losi and HPI models: y1406/01 - Big Digger y1407/01 - Cross Bond y1408/01- Over Lander y1409/01 - Giant Grip y1417/01 - Ultra Grip Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (24 mm hex for Losi and HPI Baja 5 Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. Wheels drives:18 mm square for FG & co.24 mm hex for Losi, HPI Baja 5 cars.Contents:2 pieces / 1 pair

BIG DIGGER 170x60 with black MadMax Extreme rims with 20 beadlock screws, with 18 mm square socket and reinforced orange beadlock rings for FG, Smartech and many more. Due to the extreme load created by the MadMax BIG DIGGER tires the rim was optimized again with a reinforcement ring.The MadMax tires had 84 extremely strong, with more than 1 cm² cross-section and 6 mm tread depth, allow for best power transfer and provide excellent grip even on loose surfaces like sand or soil.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars. We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmReinforced 18 mm square wheel drive 1 pairThe video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

CROSS BOND 170 x 60 mm tires mit MadMax Extreme 20 bolt-beadlock rims with 18 mm wheel square and reinforced beadlock rings were designed for use on loose surfaces. The extremely rigid and differently structured lugs of the CROSS BOND ensure optimum power transmission and also allow for excellent grip on loose surfaces, such as sand and soil. The lugs are raised at the treads outside, and therefore provide maximum grip, particularly when cornering where the tire is canted to the outside. Due to the extreme load created by the MadMax CROSS BOND tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars. We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmReinforced 18 mm square wheel driveThe video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!