Mielke S-1202 Clutch bell for SR 88 R (Mecatech System)

€59.90*

Prices incl. VAT plus shipping costs

Available

Product number: mielke_s_1202

EAN: 4058575120346

Product information "Mielke S-1202 Clutch bell for SR 88 R (Mecatech System)"

Genuine Mielke spare/option part.

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

No reviews found. Share your insights with others.

Similar products

y0726 Gas-nitrided tuning clutch bell for Losi 5ive-T/2.0/B and Mini

Gas-nitrided tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface and face which guarantees dimensional stability even under high loads! The shaft is a tiny bit longer than stock (about 0.2 mm) to prevent the bearings from binding.Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Extreme clutch.Suitable for genuine slot drive Losi pinions. Comes with bolts and spring washers included.The bolt hole is countersunk from the inside so you can also use a flat head screw from the inside and a nut on the outside if you like. Content:1 pieces

€49.90*

y0723 Gas-nitrited tuning clutch bell for FG, Smartech/Carson, Harm, RS5 & Co.

Genuine HT spare/option part. Gas-nitrited tuning clutch bell; machined from high grade steel with vents for cooling of the clutch system and holes for easy clutch adjustment. The clutch bell features a significantly reinforced wearing surface which guarantees dimensional stability even under high loads!For best mounting of the pinion the clutch bell shaft has to flats with a 90° offset. As an additional safety device a M5 bolt with washer (included) replaces the E-clip found on stock clutch bells.Suitable for many 1/5 and 1/6 cars, such as all FG (except Formula 1), Carson a.s.o.Contents:1 piece

€49.90*

6049/01 FG Clutch bell

Genuine FG spare/option part. New version clutch bell for all FG cars except Formula 1. Contrary to the previous version 6049 the flat areas for the pinion set screws are angled at 90° instead of 180° (see pic).Dimensions:Shaft diameter 10 mmShaft length 38,2 mmOverall length 61 mmAouter diameter bell 58 mmInner diameter bell 56 mmContent:1 pieces

€54.90*

y0729 Gas-nitrited tuning clutch bell for HPI Baja, Carson Wild GP Attack models, 1 pce.

Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface whichguarantees dimensional stability even under high loads!Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM clutches Big Scale Extreme and Cross.Suitable for slot drive HPI Baja pinions, both stock using a 4mm bolt and aftermarket ones for 5mm bolts. Comes with M4 and M5 bolts included.

€49.90*

7460 FG 2-Speed clutch bell - 1pce.

Suitable for all FG 2-speed gear boxes.Dimensions:Shaft diameter 10 mmShaft length 56 mmOverall length 79 mmAouter diameter bell 58 mmInner diameter bell 56 mmContent:1 pieces

€58.90*

32453 carson Clutch bell - 1pce.

€34.99*

10458/01 FG Clutch bell F1 f. gearwheel drive, 1pce.

Item N° 10458/01 Clutch bell F1 f. gearwheel drive , 1pce.For cars with gear drive FG no.: 10639.

€39.90*

10075 FG Clutch bell for F1 - 1pce.

Suitable for Formula 1.

€44.30*

Gas-nitrited tuning clutch bell for all cars to choose

For Model: y0726 - for all Losi 5ive-T

Different versions to choose:y0723 Gas-nitrited tuning clutch bell for FG, Smartech / Carson, Harm, RS5 & Co..Gas-nitrited tuning clutch bell; machined from high grade steel with vents for cooling of the clutch system and holes for easy clutch adjustment. The clutch bell features a significantly reinforced wearing surface which guarantees dimensional stability even under high loads!For best mounting of the pinion the clutch bell shaft has to flats with a 90° offset. As an additional safety device a M5 bolt with washer (included) replaces the E-clip found on stock clutch bells.Suitable for many 1/5 and 1/6 cars, such as all FG (except Formula 1), Carson a.s.o.y0726 Gas-nitrited tuning clutch bell for Losi 5ive-TGas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface and face which guarantees dimensional stability even under high loads! The shaft is a tiny bit longer than stock (about 0.2 mm) to prevent the bearings from binding.Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Scale-Cross clutch.Suitable for genuine slot drive Losi pinions. Comes with bolts and spring washers included.y0726/01 Gas-nitrited tuning clutch bell for Losi DBXLGas-nitrited tuning clutch bell with black oxide coating, machined from high grade. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well. This clutch bell is dimensionally identical to the stock part. Heat treatment and the use of a high grade material guarantee long service life.Due to a special heat treatment the clutch bell surface is shaded; this does not effect the function, but ensures great durability.y0729 Gas-nitrited tuning clutch bell for HPI Baja models, 1 pce.Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface whichguarantees dimensional stability even under high loads!Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Scale-Cross clutch.Suitable for slot drive HPI Baja pinions, both stock using a 4mm bolt and aftermarket ones for 5mm bolts. Comes with M4 and M5 bolts included.

€39.90* €49.90* (20.04% saved)

10458 FG Clutch bell for F1 short - 1pce.

Clutch flange bearing for the F1 clutch bell. The clutch bell of the engine is guided through the sparate bedding of the flange bearing. Additional the clutch bell runs centrical to the clutch blocks. The mounting of the flange bearing is only possible in connection with the engine quick fix system and the short F1 clutch bell. Suitable for the F1 Sportsline in combination with Solo and Zenoah engines. Standard equipment of F1 Competition.Shaft size length x diameter: 45 x 10 mm

€39.90*

7472/01 FG Tuning clutch bell hardened, 1 pce.

Item N° 7472/01 Tuning clutch bell hardened, 1 pce.Case-hardened clutch bell made of hard andtough steel, without cooling hole, therefore suitablefor Off-Road Buggies.

€64.90*

y0726/01 Gas-nitrited tuning clutch bell for Losi DBXL+MTXL

Genuine HT spare/option part. Gas-nitrited tuning clutch bell with black oxide coating, machined from high grade. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well. This clutch bell is dimensionally identical to the stock part. Heat treatment and the use of a high grade material guarantee long service life.Due to a special heat treatment the clutch bell surface is shaded; this does not effect the function, but ensures great durability.Contents:1 piece

€49.90*

Customers also viewed

2012-241 Mecatech Servo Saver nut o-ring

Genuine Mecatech spare/option part for the FW01.Contents:4 pieces

€5.50*

2012-28/01 Mecatech steering limiter for Mecatech FW01

Fits Mecatech FW01Content of set:2 pieces of aluminum steering limiter4 pieces of rubber shock absorbing bushings2 pieces of allen head bolts M4 x 20 mm

€27.90*

7303/10 FG Special oil seal, 2pcs.

Dust-proof shaft sealing rings to seal the crank shaft of Zenoah and Chung Yang engines. The assembly of these sealing rings is necessary for the use in extremely dusty terrain. Soft material and improved sealing lips prevent an entry of dust and sand in the crankcase which can result in a total damage of the engine.

€36.90*

This product is no longer available.

LOS251095/01 Losi Steering Rack for DBXL-E 2.0

Genuine Losi spare/option part. Contents:1 piece

€14.99*

This product is currently not available.

Mecatech FW01 Touring car, wheelbase 510 mm, Performance Kit -- Europe- and world champion

The Mecatech FW01 is for sure the currently most innovative 1/5 race car designed for the dedicated and technically enthusiastic rc car driver.Everyone is enthusiastic about the perfectly fitting and precise workmanship at the highest level. Only high quality materials are used for the production.Since many years Mecatech is a well-know premium manufacturer of largescale hydraulic brakes or shocks and, as only a few may know, a technology expert for a number of Formula 1 racing teams!The Performance Kit from the FW01 is particularly intended for "racer" and differs from the Chassis Kit model by the Performance Kit. Here the list of parts are not including:DifferentialEngine Clutch, Airbox and tuned pipe systembody shell and tiresElectonic components such as servos, batteries and Remote controlPerformance Kit:engine brace left and rightfront stabilizer bar 2.75 mm titanium ready for installationrear stabilizer bar 1.75 mm titanium ready for installationthe two 80 gram front weightsthe two smaller 80 gram center weightsWith the Performance Kit the vehicle is quasi equipped as used at races!Stock gearing:Clutch pinion / spur gear: 36T / 64TLayshaft pinion / differential: 24T / 73TCurrently the Mecatech FW01 is for sure the benchmark of the 1/5 scale racing scene! In the first year Markus Feldmann won with his FW01 1: 5 Mecatech on one of the world's finest and most demanding race track in Lostallo / SwitzerlandMecatech is multiple German, European and World Champion with the FW01 and as the last result:Markus Feldman wins the European Championship in Tourlaville/France. All top 5 positions went to drivers running a Mecatech FW01. 7 out of 10 finalists cars were Mecatech FW01.Although the fit of the Mecatech FW01 parts makes the assembly of the car a great experience, some of our customers want to use the expertise of our shop and wish their FW01 fully assembled and tuned in by us! The complete assembly of your FW01 by our workshop is possible for an additional charge. Please note that the costs of the full assembly with servos a.s.o. do not include the price of any rc-components. If you do not have a suitable radio system with servos and batteries as well as switch and charger, you have to take an additional EUR 800 to EUR 1,500 for this equipment into account. We will be happy to make you an appropriate offer. We are currently waiting for the latest version of the Mecatech FW01. We are currently waiting for the latest version of the Mecatech FW01.Included in the chassis kit:- All pinions- clutch bell- Coupling fixation- All parts and screws for mounting the enginenot included:- differential- Engine and linkage- body shell and spoilers- Airbox- clutch - engine- Electronics- TiresWe are currently waiting for the latest version of the Mecatech FW01.

€2,999.00*

Mielke 5541 Power Gearshift clutch for FG (except Formula 1+Evo2020), Harm, RS5, Mix, 2,4mm springs with long clutch carrier

The new adjustable system features two aluminum and one carbon pad with special 2.4 mm springs.Weight of the complete clutch is 70 grams. Very wear resistent when running with the recommended clutch bells.Adjustable friction points: First gear - 8.500 U/min. Second gear - 9.300 U/min. Third gear - 10.100 U/min. Fourth gear - 11.000 U/min.With tool #5445 the engagement speed can be adjusted to different settings within a range from about 8,500 to 11,000 rpm.For RS5 models from version T14!

€129.50*

2012-99 Mecatech Pinion Z35

Genuine Mecatech spare/option part for the FW01.Content:1 piece

€33.00*