Skip to main content
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

2020-20 Mecatech Racing bi-material clutch shoes

Product information "2020-20 Mecatech Racing bi-material clutch shoes"

Mecatech bi-material clutch shoes for Mecatech 3-shoe clutch.

Content:
  • 3 pieces

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Customers also bought

Average rating of 0 out of 5 stars

2012-94 Mecatech Clutch Flange Spacer
Genuine Mecatech spare/option part for the FW01.Content:1 piece

€7.50*

Average rating of 0 out of 5 stars

2012-127 Mecatech Bush for rear Wheel toe in 4,5°
Genuine Mecatech spare/option part for the FW01.Content:4 pieces

€29.50*

Average rating of 0 out of 5 stars

ST-AN22 SPEED TEC AN - Expansion sealing gasket for ‚cylinder with two bolt 0,25mm
Genuine Speed-Tec spare/option part. For Zenoah G230/G260AN - expansion sealing gaskets are in use in the 2-stroke motor sports for years and are based on NBR-linked cellulose fibers. They are especially used for sealing hot oils, greases and fuels! The sealing material is compressed during assembly, and as soon as it comes into contact with fuel, it swells again. Thus it is e.g. possible to make up for irregularities in the sealed surfaces (e.g. cylinder / crankcase) and seal them properly! The material of the SPEED TEC AN - expansion sealing gaskets guarantees a very good dimensional accuracy and is often the solution for leaks on your engine! Technical data of the material in contact with fuel:Rebound ASTM G > 30%; increase in thickness < 5%; weight gain < 55%;Compressibility ASTM F36 G 22.5% +/- 2.5 27.5% +/- 7.5 The SPEED TEC AN - expansion sealing gaskets are available in the following versions:# ST-AN26V carburetor gasket 0,25/0,50 mm# ST-AN25I insulator gasket 0,25/0,50 mm# ST-AN24L air filter gasket 0,25/0,50 mm# ST-AN22 cylinder gasket, two bolt 0,25/0,50 mm# ST-AN42 cylinder gasket, four bolt 0,25/0,50 mm# ST-AN23G crank case gasket 0,25/0,50 mmContents:1 piece

€4.40*

Average rating of 0 out of 5 stars

2012-122 Mecatech Rear Driving Axle
Genuine Mecatech spare/option part for the FW01.Content:1 piece

€23.00*

Average rating of 0 out of 5 stars

2012-21 Mecatech Spacer Adjustment 2,0 mm
Genuine Mecatech spare/option part for the FW01.Content:4 pieces

€8.50*

Average rating of 0 out of 5 stars

7335 FG Insulator gasket for Zenoah / CY / Fuelie
Genuine FG spare/option part.For Zenoah G230/G240/G260/G270/G290Applications:Click here!Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContents:1 piece

€4.30*

Similar products

%

Average rating of 0 out of 5 stars

y19302/01 Flywheel and Clutch puller CY, Zenoah, HPI, Losi
Genuine HT spare/option part. Especially for CY / Zenoah G230/240/260/270/290/320, HPI and Losi engines.Can be used for removal of the standard clutch as well!Contents:1 piece

€17.90* €22.90* (21.83% saved)

Average rating of 0 out of 5 stars

5646 Mielke Mix clutch pads single for Power Gearshift Converse II clutch
Genuine Mielke spare/option part.Contents:3 pieces

€44.90*

Average rating of 0 out of 5 stars

5647 Mielke Springs 2,4 mm made from special steel for Converse left
Genuine Mielke spare/option part. Contents:3 pieces

€9.90*

Average rating of 0 out of 5 stars

Mielke 5445 Power Gearshift clutch adjustement tool
Adjustment tool for Mielke Power Gearshift clutches #5440 and #5441.

€19.90*

Average rating of 0 out of 5 stars

Mielke 5447/03 Springs 2 mm made from special steel
Genuine Mielke spare/option part. Replacement part for Mielke Power Gearshift clutches #5440 and #5441.Content:3 pieces

€9.90*

Average rating of 0 out of 5 stars

5445/1 Mielke tool for clamping of all Power-Gearshift clutches
Genuine Mielke spare/option part. For easier change of springs or clutch shoes.Contents:1 piece

€34.90*

Average rating of 0 out of 5 stars

Mielke 5648 Springs 2,5 mm made from special steel (blue)
Genuine Mielke spare/option part. Replacement part for Mielke Power Gearshift 2 clutches.Contents:3 pieces

€9.90*

Average rating of 0 out of 5 stars

AT-DBXL013 ATOP Clutch bell carrier for Losi Desert XL+MTXL
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum clutch bell holder for Losi DBXL+MTXL. Compared to the stock plastic part the higher strength of the aluminum part ensures secure seat for the bearings, increased dimensional stability at high temperatures and reduced operating temperatures for the bearings due the aluminums thermal conductivity. Larger bearings (12 x 28 x 7) for higher load capacity. Comes with ball bearings and spacer tubes included.It is recommended to use the ball bearings/bushings adhesive (y0113 Thread locking compound).Contents:1 set

€34.90*

Average rating of 0 out of 5 stars

5649 Mielke Carbon clutch pads single for Power Gearshift Converse II clutch
Genuine Mielke spare/option part.Contents:3 pieces

€44.90*

Average rating of 0 out of 5 stars

Mielke 5447 Springs 2,3 mm made from special steel
Genuine Mielke spare/option part. Replacement part for Mielke Power Gearshift clutches #5440 and #5441.Contents:3 pieces

€9.90*

Average rating of 0 out of 5 stars

y1379 Pinion fastening set with nut for Losi 5ive-T/2.0 and Mini
This set allows for fastening the pinion to the clutch bell utilizing a full metal self locking nut when using our gas-nitrided clutch bell y0726. The screw will be fully inserted into the clutch bell from the backside using high strength thread locking compound. This setup provides a couple of significant advantages:This self locking nut does not use the usual plastic insert; therefore it is completely temperature resistant!Theres no need to wait for the thread locking compound to cure after a pinion change; the connection is safe and ready to use immediately. For safety reasons nut and spring lock washers should only be used once.No need to worry about worn-out Allen screw heads.In case the screw ever breaks at the point where it enters the pinion, it can still be removed with ordinary tools. Theres still the like new screw head inside the clutch bell ready for screw removal. Set includes:2 pieces of high strength 12.9 grade screws10 pieces of full metal self locking nuts10 pieces of spring lock washers

€5.90*

Average rating of 0 out of 5 stars

Mielke 5449 Carbon clutch pads single, 3 pcs.
Genuine Mielke spare/option part.Spare parts for Mielke clutch´s no.: 5442, 5440, 5441.Contents:3 pieces

€44.90*

Customers also viewed

Average rating of 0 out of 5 stars

2021-05 Mecatech Insulator
Genuine Mecatech spare/option part. Great reduction of heat transfer between cylinder and carburetor due the no connection of any metallic parts.Machined from billet heat resistant special polymer.Special duct geometry, completely machined on 5-axis cnc machine.Contents:1 piece

€89.90*

Average rating of 0 out of 5 stars

2020-10 Mecatech Clutch blocks Alloy for Mecatech 2020 clutch
Genuine Mecatech spare/option part. Contents:1 set

€51.00*

Average rating of 0 out of 5 stars

2020-03 Mecatech Adjusting tool for Mecatech 2020 clutch
Genuine Mecatech spare/option part. Special Clutch Adjusting tool required to adjust the new 2020 Mecatech clutch.Contents:1 piece

€35.00*

Average rating of 0 out of 5 stars

2012-146 Mecatech Braket Mount rear Body Support
Genuine Mecatech spare/option part for the FW01.Content:1 piece

€23.00*

Average rating of 0 out of 5 stars

y0052 HT venturi adaptor set
luftf_0025 Engine: Solo
Upgrade in case you already own the airbox.Includes venturi adaptor, K&N filter, K&N filter oil (200ml spray can) and K&N filter cleaner (355ml bottle).When using a K&N Filters should observe the foam precleaner y19017 be used with wet-foam air filter oil. To complete coverage of the K&N filter Combat is respected, because the K&N filter without prefilter-oiled foam is to permeable to the off-road use.Please note:The flange on the bottom of the K&N filter has to be cut off for installation on the venturi adaptor!

€81.10*

Average rating of 0 out of 5 stars

2020-18 Mecatech Adjustable 3 Shoe Clutch
Genuine Mecatech spare/option part. This completely new developed adjustable clutch fits by default in combination with the Mecatech and Genius clutch bells. But combined with a special washer it can also be used on other brands.The shoes in this clutch are mounted in the direction of rotation (reverse), similar to other actual clutch designs.It is of course possible adjust this clutch to engage at different rpm's. The clever design of this clutch makes it very easy to disassemble and adjust the clutch. This requires only 2 separate tools.The first tests in Italy have shown that even after 2 hours of continuous driving, the clutch acts more smooth and precise compared to others. Furthermore the engagement remains very stable and the wear was negligibleContents:1 piece

€149.90*

Average rating of 0 out of 5 stars

2020-05 Mecatech Clutch blocks Mix for Mecatech 2020 clutch
Genuine Mecatech spare/option part. No longer AVAILABLE !!!!  Replacement is Mecatech 2020-20Contents:1 set

€51.00*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Agency