6079/05 FG Ball driving axle M8
€32.95
Available
Product information "6079/05 FG Ball driving axle M8"
Inhalt:
- 1 Stück
Lebacher Strasse 4
66113 Saarbrücken
Germany
Login
Accessories / Spare parts
Genuine FG spare/option part. Part is delivered in silver or black color from vendor!Contents:10 pieces
Customers also bought
Twin hose bracket for hoses up to 7 mm outer diameter. With 5 mm hole for installation by screw or cable tie.Keeps your car's fuel lines in place. Especially helpfull with tuned pipe layouts running close to the engine.Screws with part number #6726/25 are recommended for installation on the fan cover.
Genuine Mecatech spare/option part for the FW01.Attention:does only fit the chassis plate with corresponding cut-outs and mounting provision!Content:2 pieces
Genuine FG spare/option part. For fastening on the rear shock mount.Contents:1 piece
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Genuine FG spare/option part. Suitable for all FG models and other. To complete one car you need two sets.For 2WD models you need two sets and for 4WD models you need four sets.Contents:2 pieces
Genuine Mecatech spare/option part. Replacement part for Mecatech twin piston hydraulic brake. Assembled with seals.Note from Mecatech:A special tool is required for replacing the two seals on the piston. Therefore the seals are not available as separate spare parts.Contents:1 piece
Customers also viewed
Fits all FG cars and the Mecatech FW01. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins. The GPM ball drives can be partially mixed with FG parts. The heads of the GPM driveshafts fit into FG differential cups or wheel shafts.The opposite combination, i.e. FG shafts in GPM differential cups or wheel shafts does not always fit. We had tests where some FG shafts fit neatly, but due to slight tolerances others who did not fit into the very same cups/shafts. For this combination, we can not guarantee compatibility! Dimensions: Diameter: 8 mmTotal length 76.6 mm
Genuine FG spare/option part. Part is delivered in silver or black color from vendor!Contents:10 pieces
Genuine FG spare/option part. For ball drive system only!Diameter: 8 mm.Contents:1 piece
Genuine Mecatech spare/option part for the FW01.Attention:does only fit the chassis plate with corresponding cut-outs and mounting provision!Content:2 pieces
Stud bolt with double sided thread for well-running brake linings, no jamming of the brake linings possible. Suitable for all mechanical disk brakes.
Genuine FG spare/option part.Fits all FG off road cars except Leopard and Leopard race.Contents:1 piece
Genuine FG spare/option part. Reinforced front drive axle from M6 to M8 thread. Suitable for all 2WD Buggy models. For mounting the self-locking wheel nuts M8 Item No. 6115 are necessary.Length: 60 mm.Contents:1 piece