Genuine Area spare/option part.CNC-machined rear shock tower from 6061-T6 aluminum by Area RC.Strong (7 mm thick), yet light weight version (98 grams). Comes with aluminum cage brackets included!Contents:1 piece

Genuine ATOP spare/option part. CNC-machined from 6061-T6 aluminum by ATOP.New improved designs combines increased strength with reduced weight. Both together give a total weight of 130 grams.Contents:2 pieces

Genuine ATOP spare/option part. CNC-machined from 6061-T6 aluminum by ATOP.New improved design combines increased strength with reduced weight (59 grams).Contents:1 piece

Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP RC, increase track width for 25 mm and allow for the use of HPI 5T, Losi 5ive-T, 5ive-B and Mini rims. 5 mm o-rings protect against drive pin loss. Set of four inclusive o-rings, drive pins and closed wheel nuts (wrench size 24 mm!).Contents:1 set

Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP.Protects chassis plate and transmission case over rough terrain. Also reinforces the chassis plates narrow section in front of the gear case. Thickness: 4 mm, weight: complete 141 grams.Contents:1 set

Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP.Protects chassis plate and transmission case over rough terrain. Also reinforces the chassis plates narrow section in front of the gear case. Thickness: 4 mm, weight: 85 grams.Contents:1 piece

Genuine ATOP spare/option part. Upper rear camber rods with guide bushing set and with pivoted steel ball joints right/left thread and locknuts for 5ive-T. Balls with 6 mm hole, adapter bushings for 5 mm screws, shortest distance between mounting points (center/center) 140 mm. Contents:2 pieces

Genuine ATOP spare/option part.AT-5T015 ATOP Aluminum front transmission case Losi 5ive-T/B and MiniCompletely cnc-machined front transmission case from billet 6061-T6 aluminum by Atop. Service life of ball bearings and ring & pinion will greatly benefit from the increased strength of this aluminum case. It also ends the problem of stripped tread holes for the mounting screws. Weight:approx. 297 gramsAT-5T016 ATOP Aluminum rear transmission case Losi 5ive-T/B and MiniCompletely cnc-machined rear transmission case from billet 6061-T6 aluminum by Atop. Service life of ball bearings and ring & pinion will greatly benefit from the increased strength of this aluminum case. It also ends the problem of stripped tread holes for the mounting screws. Set comes with bearing carriers included! We recommend to install the bearings using thread locking compound y0113. Bindulin silicone sealant y19015 is recommended for installing the bearing adaptors into the transmission case. Modification of the Atop bearing carriers is required when using HD differential drive cups y1477. Weight:approx. 418 gramsContents:1 set

Genuine ATOP spare/option part. Completely cnc-machined rear transmission case from billet 6061-T6 aluminum by Atop. Service life of ball bearings and ring & pinion will greatly benefit from the increased strength of this aluminum case. It also ends the problem of stripped tread holes for the mounting screws. Set comes with bearing carriers included! We recommend to install the bearings using thread locking compound y0113. Bindulin silicone sealant y19015 is recommended for installing the bearing adaptors into the transmission case. Modification of the Atop bearing carriers is required when using HD differential drive cups y1477. Weight:approx. 418 gramsContents:1 piece

Genuine ATOP spare/option part. Fits the rear plastic gearbox on all cars from the 5ive series and as spare part the ATOP gearbox AT-5T016. Stock size bearings are used.Contents:2 pieces

Genuine ATOP spare/option part. CNC-machined from 6061-T6 aluminum by Area RC.The big advantage over the stock plastic part is its temperature insensitivity. While the plastic case loses its strength with increasing temperatures and may finally disintegrate, the aluminum case stays intact.The one-piece design guarantees a true running and leak-free case. Steel bushing for drive cup shaft and O-ring.Fits front, center and rear applications on all Losi 5ive versions and Mini!Contents:1 piece

Light weight design (119 grams each), CNC-machined from 6061-T6 aluminum by ATOP a-arms fits Losi 5ive-T rear.The chassis-side is wider than stock arms to bring the large longitudinal play at this point down to a reasonable level.Bushings for the hinge pins guarantee low wear.

Delrin bushings, spare part for GPM rear lower a-arms BJ056 for HPI Baja cars, set of eight.Dimensions:Outer diameterer: approx. 8.1 mmInner diameter: approx. 6 mmLength: approx. 9.7 mm

Very nicely machined front shock tower from GPM, made of high grade 7075-T6 aluminum. The increased thickness of the upper section makes bending or breaking almost impossible. Cleverly positioned cutouts keep the weight down and make for a pleasing appearance.Direct replacement for the stock part using OEM hardware.Content:1 piece

Bushings set for GPM rear a-arms part no. LO5T055.

Full length about 127 mm long. Made from high strength 7075-T6 aluminium. 3,5 mm thickness. Stiffing reinforcing 1,5 mm wide and 1,4 mm thick.Content:Four allen head screws M6 x 20 mm Weight: 357 grams/ pair

Genuine Losi spare/option part. Contents:1 piece

Genuine Losi spare/option part. Fits Losi 5ive-T and 5ive Mini. Content:2 pieces

Genuine Losi spare/option part.Fits Losi 5ive-T, TLR 5ive-B and 5ive Mini.Dimensionally identical with Losi 5ive part B51007/55039/55040/55014.Compatible with B61039/55039/55040/55013Compatible with B51008/55041Compatible with B51008/55042Compatible with B51008/55043Compatible with B51037/55038/1Compatible with B51016Content:3 pieces

Genuine TLR spare/option part.Content:1 pieces

Genuine TLR spare/option part.Content:12 pieces Support blocks6 pieces Cross pins

Genuine TLR spare/option part. Contents:1 piece

TLR shock shaft for Losi 5ive-T, TLR 5ive-B and Mini WRC rear shocks; TiCN (titanium carbon nitride) coated; approx 96.8 mm long.Direct replacement for stock shock shaft LOSB 2852.Contents:2 pieces

TLR hinge pin for Losi 5ive-T, TLR 5ive-B and Mini WRC, front and rear; TiCN (titanium carbon nitride) coated; approx 105.5 mm long.Direct replacement for stock hinge pin from the set LOSB 2080.Contents:2 piece