LO5T331F GPM Rear Gear Box Protector for Losi 5ive-T/2.0

€29.90*

Prices incl. VAT plus shipping costs

Available

Product number: gpm_lo5t331r

EAN: 4058575034742

Product information "LO5T331F GPM Rear Gear Box Protector for Losi 5ive-T/2.0"

Full length about 127 mm long.

Made from high strength 7075-T6 aluminium.
3,5 mm thickness. Stiffing reinforcing 1,5 mm wide and 1,4 mm thick.

Content:

Four allen head screws M6 x 20 mm

Weight:

357 grams/ pair

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

AT-5T003 ATOP Aluminum top chassis brace Losi 5ive-T/2.0 and Mini

Genuine ATOP spare/option part. CNC-machined from 6061-T6 aluminum by ATOP.Complete with all required hardware.Contents:1 piece

€29.90*

AT-5T006/007 ATOP Aluminum front and rear skid plate Losi 5ive-T/2.0 and Mini

Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP.Protects chassis plate and transmission case over rough terrain. Also reinforces the chassis plates narrow section in front of the gear case. Thickness: 4 mm, weight: complete 141 grams.Contents:1 set

€49.90*

Details

y1419 Sintered steel clutch for Zenoah and many other engines from 23 cm³ to 32 cm³, incl. clutch spring

Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³. incl. clutch spring!Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!

€29.90*

y0428 Extension cable universal180/300 mm

y0428 Length: y0428/01 - 180 mm

In case the servo cable is not long enough.Two selectable lengths:y0428/01 - 180 mmy0428/02 - 300 mm

€5.90*

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€54.90*

Details

AT-5T001/002 ATOP Chassis brace Losi 5ive-T/2.0, front and rear

Genuine ATOP spare/option part. CNC-machined from 6061-T6 aluminum by ATOP.New improved designs combines increased strength with reduced weight. Both together give a total weight of 130 grams.Contents:2 pieces

€64.90*

Customers also viewed

LOSB2076 Losi Rear wishbone arm set 5T, 2 pcs.

Item N° LOSB2076Rear wisbounes Arm Set 5T, 2 pcs.

€29.99*

y1419 Sintered steel clutch for Zenoah and many other engines from 23 cm³ to 32 cm³, incl. clutch spring

Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³. incl. clutch spring!Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!

€29.90*

y0428 Extension cable universal180/300 mm

y0428 Length: y0428/01 - 180 mm

In case the servo cable is not long enough.Two selectable lengths:y0428/01 - 180 mmy0428/02 - 300 mm

€5.90*

AT-5T028 ATOP Aluminum radio plate Losi 5ive-T 1.0 and 2.0 for dual steering servos

Genuine ATOP spare/option part. CNC machined 6061-T6 aluminum radio plate from ATOP, fits Losi 5ive-T 1.0 and 2.0.This all-aluminum unit allows for installation of dual steering servos. The servo hole patterns are suitable for Losi original servos / servos with the size of 900S and K-Power.The box for the receiver battery has internal dimensions of 142 x 65 x 32 mm.Available with additional genuine Losi S900S 5ive-T steering servo incl- Y-harness in the options menu.Contents:1 piece

€169.90*