New developed alum. servo arm in high-strength material with M3 threaded holes for the assembly of the throttle pivot posts 06534/02 and 06534/03. The fitted transverse slot makes the mounting of the servo arm on the servo toothing much easier.Measures:Total length: 53 mmWidth: 10 mmThickness: 3,1 mmThread: 3 mm

Rugged plastic servo arm for all saleable servos, mm holes, suitable for all car models. Arm thickness 4 mm.2 pieces

Genuine FG spare/option part.Contents:1 piece

Alloy servo arm made of high-strength alloy material.Length over all 53 mm.Distances bore to center of servo horn: 11.5 / 17.5 / 23.5 mm. Inner holes 2.2 mm, middle and outer ones with M3 thread.Content:1 piece

Genuine FG spare/option part. New developed alum. servo arm in high-strength material with M3 threaded holes for the assembly of the throttle pivot posts 06534/02 and 06534/03.Fits Hitech HS-7955 and HS-5585MH.Contents:1 piece

Genuine FG spare/option part. Splash-proofed receiver box for all merchantable small receivers, suitable for all car models 1:12 - 1:5.Dimensions:Length: upper section 92 mm, bottom 69 mmHeight: 48 mmWidth: 38 mmContents:1 piece

Non-transparent black shrinkdown plastic tubing to shrink the receiver batteries. Superficial measure 70mm.

Genuine FG spare/option part. Polarized and gold plated connector system.Content:1 piece

Genuine FG spare/option part.Contents:1 piece

Genuine FG spare/option part.Contents:1 piece

Genuine FG spare/option part.Two-pole, reverse-polarity protected plug with very high current capacity. The opening in the contact for the cable has a diameter of 6.5 mm, which is suitable for stranded cables up to about 16 mm² (~ 5 AWG). The easy to grab housing ensures easy disconnection.For assembly, the contact with a soldered cable is press fitted into the housing from the front, where it snaps into place.When used without the blue housing, the contacts are also compatible with the 8 mm sockets found on many larger ESCs.Contents:2 pieces

Item N° 6545 FG gold contact plug-in system 2mm - 2pcs.Reverse battery protected gold contact plug-in system. A further great advantage of our plug-in system is the fixing of a plug on the receiver box or rc-plate with screws. This makes the connection of plug and bush easier.

Item N° 6545/01 FG gold contact plug-in system 2mm - 10pcs.Reverse battery protected gold contact plug-in system. A further great advantage of our plug-in system is the fixing of a plug on the receiver box or rc-plate with screws. This makes the connection of plug and bush easier.

Genuine FG spare/option part.Affordable receiver battery Ni-MH 6V/2000 mAh for the electric power supply of receiver and servos, with JR-Graupner bush, rechargeable.Measures:Width: 112 mmHeight: 46 mmDepth: 23 mmUniversal

Genuine FG spare/option part.Measures:Width: 111 mmHeight: 47 mmDepth: 23 mmContents:1 piece

Receiver cable, ready-made with FG gold contact plug-in system for Futaba plug.total length 20-25cm

Receiver cable, ready-made with FG gold contact plug-in system for Multiplex plug.total length 20-25cm

Genuine FG spare/option part. Charger 220/230V for receiver (Futaba and Hitec) and transmitter (Futaba, BEC, JR-Graupner and T-connector). Charge control over LEDs. Suitable for the Hitec Radio Control System.Images may differ from the original.Charging currents:Transmitter: 180 mAPower pack: 250 mAContents:1 piece

Genuine FG spare/option part. A switch which one well through a hole in the radio box and put on top and bottom can be secured with nuts.Contents:1 piece

Genuine FG spare/option part. Waterproof switch equipped with JR connector for receiver and FG gold contact connector for the receiver battery. Used to cut the power supply of receiver and battery. With fastening screw thread.Suitable for all radio control systems.Contents:1 piece

Genuine FG spare/option part.Recommended for batteries with at least 200 mAh capacity.The charger is suitable for LiPo batteries from 2S to 4S (7.4 to 14.8 volt), connected via balancer port. The port has JST XH connector. Maximum charging current: 4 A, maximum charging output: 50 W.Charging current will be adjusted automatically. Removable mains cord (230 volt) is included.Content:1 piece

The Y-cable is required to drive two servos from a single receiver channel.Content:1 piece

The Y-cable is required to drive two servos from a single receiver channel.Content:1 piece

Genuine T2M spare/option part.For secure transport and storage of LiPo batteries.For batteries up to approx. 175 x 75 x 70 mm.Contents:1 piece