6550 FG Switch for receiver cable
Product information "6550 FG Switch for receiver cable"
Genuine FG spare/option part.
A switch which one well through a hole in the radio box and put on top and bottom can be secured with nuts.
Contents:
A switch which one well through a hole in the radio box and put on top and bottom can be secured with nuts.
Contents:
- 1 piece
Login
Accessories / Spare parts
Genuine FG spare/option part. Accessories for FG switch no.: 6550 Switch f.receiver cable und 6551 Receiver cable with switch FG/JR.Contents:1 piece
Similar products
%
tt_tt1000 Connector:
TT1000/01 Universal in - Universal out
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece
BEC type connectors for both battery and receiver.
Futaba / universal type connectors for both battery and receiver.
schalter_elektronisch Battery connector:
y0314/01 Universal connector
Genuine HT spare/option part.Electronic receiver switch, rated 5 A continuous / 15 A peak. This switch does not use mechanical contacts for the load, therefore it is less prone to failure caused by vibrations or dirt.The swith uses two separate connectors to distribute the load at the receiver terminals.With drilling template and mounting material.Contents:1 piece
servo_strom_mit Application:
y0368 - 3 servos, battery connector universal+ 2EUR
Servo direct power supply cable with electronic switch, 1 pce.With this cable the servos get their current directly from the battery without straining the receiver circuit board.The integrated electronic receiver switch is rated 5 A continuous / 15 A peak. This switch does not use mechanical contacts for the load; therefore it is less prone to failure caused by vibrations or dirt. With separate charging connector.With drilling template and mounting material included.
Variants from €54.90*
Old version Multiplex type connectors for both battery and receiver.
%
akku_0021 Battery connector:
y0210/04 MPX old
Genuine HT spare/option part. Water protected receiver switches, silver plated contacts. Many different connectors to choose from.UniversalFGBECHigh currentContents:1 piece
Genuine FG spare/option part. Waterproof switch equipped with JR connector for receiver and FG gold contact connector for the receiver battery. Used to cut the power supply of receiver and battery. With fastening screw thread.Suitable for all radio control systems.Contents:1 piece
Customers also viewed
The FG Sportsline Formula 1 electric convinces not only by its appearance, but rather by its technical achievements. The unique details such as push rods, horizontal oil pressure shock absorbers, double wishbone and much more can be found in almost no other model.The chassis is built on a high-strength 5mm aluminum chassis plate and thus offers extreme stability. Countersunk holes in the chassis plate allow the screws to be flush, ensuring a flat surface under the model. Versatile adjustment options on the front and rear axles allow the model to be perfectly adapted to your own needs. Adjustments such as camber, caster, etc. are no problem whatsoever, even for beginners, and are made via the double a-arms, which provide maximum stability at the rear axle by means of additional track rods. Also the adjustable aluminum oil filled shock absorbers convince on full length and offer maximum performance even on a very difficult underground. The above mentioned push-rod suspension enables play-free power transfer from the suspension to the shock absorbers, which is essential for precise driving.The factory-mounted combination of 980KV motor and 160A MAX6 esc provides performance that is second to none. With a 6S 22.2V (4S 14.8V is also possible) LiPo batteries, the motor reaches a final speed of about 25,000 rpm, leaving a comparable combustion engine far behind. The braking is done by the 980KV motor and is very strong. Within a few meters the model comes from top speed to a standstill. Those who have searched in vain for reverse gear with a combustion engine will find it with the electric version. The operation is very easy, if you press the brake lever once, you hit the brakes. If you press the brake lever twice, you shift into reverse. With the help of a programming card (available separately) you can adjust all ESC values according to your needs. This includes setting options for power, brake force, low-voltage protection and much more. Furthermore, the model has the following technical: Features: 160A MAX6 esc, 6S compatible (4S also possible) 980KV brushless motor Waterproof components Adjustable aluminum oil filled shock absorbers Aluminum levers for the shocks Aerodynamic Lexan body shell 5mm thick aluminum chassis plate Mounting compartment for steering servo Mounting compartment for separate brake servo (for mechanical/hydraulic brakes) Cogged belt drive Side battery mounts for optimal weight distribution Custom CNC machined motor mount Unique double a-arms Push rod suspension Treaded F1 tires Tuning ball drive shafts Dimensions: Length: 960 mm BrWidtheite: 440 mm Height: 230 mm Wheelbase: 620 mm Technical data 980KV brushless motor: Max. Voltage: 33V Max. Current: 130A Max. Speed: 30.000RPM Power in watts: 4250W Rotor poles: 4 No-load current: 2.8A Resistance: 0.0128 Length: 82mm Diameter: 55 / 58mm with fins Weight: 880g Shaft diameter: 8mm Free shaft length: 30mm Weight: 880g Technical data Max6 esc: Continuous current: 160A Peak current: 1050A Battery: 3S - 8S LiPo or 9-24 cells NiMH BEC: 6V/7,2V - 3A/6A Abmessungen:70x56x46,5mm Weight: 240g Note: In our online shop you can also find a detailed 360° illustration, where especially the technology of the FG Formula1 electric chassis can be seen.Note battery mounting:When mounting the l/h side LiPo battery, you must always make sure that it does not rub against the drive pulley. For this purpose, a 5 mm thick piece of foam mat or something similar between battery and battery holder is sufficient to ensure an appropriate distance. For driving you still need: 2 drive batteries incl. charger Battery dimensions maximum: Length 143 mm/5,6 Width 48 mm/1,9 Height 40 mm/1,6 Connector EC8 The RTR equipment (remote control and steering servo!) The body shell comes unpainted! In our online store you can use our store configurator (shopping cart selection / options menu) to add the desired parts, as well as the completely painted body. Here at our Ebay offer selectable: RTR equipment (remote control and steering servo) fully assembled! Painted body shell incl. decals Formular 1 models in action!