B58004 HV2060MG Digital Servo (48-62kg）

Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

Genuine HPI spare/option part. Part is delivered in silver or black color from vendor!Content:6 pieces

Genuine FG spare/option part.Spare part for FG no.: 6464.Dimensions:Outer diameter 61 mmInner diameter 20 mmHeight 71 mmContent:2 pieces

BUILD YOUR OWN ORIGINAL,AUTHENTIC HPI BAJA 5BHPI large scale fans, we have heard you! The one and only original HPI Baja 5B is BACK and ready for you to build from the ground up! The HPI SBK collection of Self Build Kits grows with the addition of not just one, but TWO 1/5th scale HPI kits! Fans of large scale off-road RC will be super excited to build their own gas-powered 1/5th scale Buggy with the HPI Baja 5B Self Build Kit!When the HPI Baja 5B buggy was first introduced, large scale RC was very expensive and quite difficult for the average RC hobbyist to experience. Using highly durable parts and innovative design features, HPI brought large scale off-road to new enthusiasts and ushered in a new, BIGGER era of RC!Now, YOU can build and own the legend! Experience the thrill and excitement of building a car which ends up being over 80cm (nearly 32 inches) long and weighing nearly 10kg (over 21 lb)! Just install your own engine and electronics as you build the HPI Baja 5B and you'll be ready for any adventure that comes your way!With extra-tough drivetrain parts like the viscous torque differential, super-durable composite spur gear with internal damping and all-metal drivetrain, the HPI Baja 5B is ready for your 23-32cc 2-stroke engine so you can experience the joy of gas-powered RC and up to 30-minute runtimes!The HPI Baja 5B is also equipped with extra-big and super-tough suspension parts, featuring awesome HPI durability! With its expertly designed molded composite suspension plus extra-long adjustable HD shocks, and massive high impact nylon 3-piece beadlock wheels, the Baja 5B is ready for full-speed racing on any off-road circuit!The 4mm thick 6061 aluminum monocoque chassis gives the HPI Baja 5B the classic desert racing buggy look. Precisely bent into shape for maximum strength, the chassis provides the mounting points for the engine and suspension, forming the backbone of the car. Precise steering is provided by a dual-bellcrank rack and cam-type servo saver. Aluminum parts are anodized in cool gunmetal and the classic Baja desert racer clear polycarbonate body is included in the SBK kit, ready for your custom racing scheme!The Baja 5B SBK is a great addition to your HPI collection, as well as a fabulous introduction to large scale buggies!RACING CHASSIS DESIGN & LAYOUTThe narrow channel chassis made from rigid 4mm 6061 aircraft aluminum and gives the HPI Baja 5B a classic desert racing buggy look and extreme stiffness and durability. The U-shaped chassis is protected at the rear with a thick plastic skid plate for extra protection to the motor and drivetrain.The tube roll cage is made of high impact nylon and topped with a real aluminum roof to carry on the classic looks. The roll cage is fully functional and protects the motor and internals from crash damage. The roll cage, radio box, body panels, wing, undertray and gear case are all mounted with fast access clips for easy maintenance. To finish you need: Engine with clutch and exhaust Remote control with servos and receiver battery Charger Two cans of Lexan paint Features Summary Unassembled 1/5th scale Off-Road Buggy Ready for your 23-32cc RC engine Ready for your electronics Enclosed radio box Baja desert racing body design Adjustable HD shock absorbers Monocoque chassis Low CG for superior handling Long travel suspension Viscous torque oil-filled gear differential All-terrain tires Beadlock wheels with metal insert hubs Aluminum rear shock tower Hard plastic skid plates Adjustable rear wing Quick access to all critical maintenance points Dual bellcrank steering Cam type servo saver Race spec Hex socket hardware Gunmetal anodizing Full set of rubber-sealed ball bearings Chassis Specifications Overall Length 817mm Height: 255mm Width: Front - 460mm; Rear - 480mm Tire Track (to center of tires): Front - 395mm; Rear - 400mm Wheelbase: 570mm Ride Height: 76mm Suspension Travel: Front - 95mm; Rear - 100mm Weight: 9.6kg (21.3lb) Adjustable Camber: front - shims; rear - screw Front caster: adjustable with shim 22 / 25.5* / 29 degrees (* stock) Toe-in: Front adjustable with tie rod; Rear adjustable with inserts 0-4 degrees (3 degrees stock set-up) Aircraft aluminum 6061 T6 monocoque chassis Double wishbone suspension with adjustable roll center F/R Drive system: HD metal gears with sealed gear box (8.382:1 gear ratio) Differential: viscous torque control with 4 pinion gears; sealed diff case with silicone oil Shock absorber: HD Aluminum coilover shock absorber with fully adjustable preload collar Wheel type: 3-piece beadlock design, high impact nylon material with inset heavy-duty metal hex hub