6031 FG Roll cage, front loop

Highlights News 2025 Tuning aluminium lower wishbones, one-piece (front and rear) FG hydraulic brakes front and rearTuning chassis plate black anodised and milled Tuning milled aluminium rear axle linkage for toe-in adjustment  Perforated tuning clutch bell Side flaps on the rear spoiler in carbon fibre Highlights Formel 1 Competition- This model is fitted with numerous aluminium parts: - front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Technical description of the FG Formula 1 Competition :The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with FG hydraulic brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition CNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ Zenoah engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, FG hydraulic brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos (each approx. 40 - 50 kg), 2 servo for throttle brake (approx. 20 - 30 kg), batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engineAirboxPipe Clear bodyshell and polycarbonate spoiler FG hydraulik brakes front and rearDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!

Item N° 60239 Plastic brace, 2 pcs.Spare part for FG Off-Road Buggy for 2WD and 4WD.

With the Futaba R404SBS, Futaba offers the fastest and most compact receiver for RC cars and boats on the market today! The R404SBS has the ultra-fast signal transmission F-4G (10 channels with telemetry at maximum transmission speed). This makes the model's response even more direct while maintaining maximum transmission reliability!The new F-4G (Futaba 4th Generation System) transmission mode supports the familiar SR mode and has an even higher transmission speed than the previous T-FHSS SR. At the same time, the size of the new F-4G receivers R404SBS / R404SBS-E could be reduced again. To make this possible, the R404SBS-E has a large, upward-pointing antenna to optimize signal reception. Due to the chosen design, the footprint of the receiver remains unchanged.To take full advantage of the speed of Futaba's F-4G SR technology, there are numerous FUTABA SV servos that can also be converted to SR mode. The following servos are currently SR compatible: BLS371SV, BLS471SV, BLS571SV, BLS671SV, BLS671SVi, BLS373SV, S9372SV, S9373SV, HPS CB700, HPS CT700, HPS CB500, HPS CT500.The R404SBS has antenna diversity. The receiver constantly compares which antenna has the better signal and switches to it in a flash. The R404SBS has the second antenna in the housing.S.BUS2 sensors can be connected to the S.BUS2 port. They transmit up to 32 telemetry data sets. The receiver has an integrated telemetry transmitter that transmits the data to the transmitter. This allows the measured values to be displayed or acoustically output at the transmitter.ATTENTION: The receiver supports HV (High Voltage) and can be powered directly from a 2s LiPo battery. Always make sure that the connected servos are also designed for HV! Technical specifications Transmission type: F-4G Frequency range: 2.4 GHz Channels: 4 PWM / 10 S.BUS Transmission power: 100 mW EIRP S.BUS Port: S.BUS2 Voltage range: 3.7-8.4V Dimensions: 25.5 x 20 x 10.6mm Weight: 5.7g Features 4/10 channel F-4G receiver 10 channels of telemetry at maximum transmission speed SR mode compatible Telemetry with S.BUS2 Telemetry with 32 channels S.BUS2 port Hi-Voltage (HV) Antenna diversity

Genuine FG spare/option part. Rubber pucks for all standard design FG spur gear carriers.Dimensions:Outside diameter: 16 mmInner diameter: 7 mmHeight: 6 mmContents:4 pieces

Genuine FG spare/option part. For FG off road, stadium and monster models except Hummer.Contents:2 pieces

Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey and Super Rock Rey.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: The adapters only fit in combination with the standard plastic steering knuckles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which then prevents the drive pin from being fitted.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fender wells will need some cutting.Please note: the wide rear wheels from MadMax or HPI do not fit!This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm

Genuine FG spare/option part. Fits all electric Off-Road cars from FG.Contents:1 piece