Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

6064 FG Differential case

Product information "6064 FG Differential case"

Genuine FG spare/option part.

Stock plastic differential case. Also available in aluminum.

Dimensions:
  • Length: 70 mm
  • Diameter: 42.5 mm
  • Flange diameter: 65 mm
  • Bearing seats: 12 x 8 mm
  • Shaft bore: 8 mm
  • Inner dimensions: 40 x 30 mm


Contents:
  • 1 piece

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Accessories / Spare parts

Average rating of 0 out of 5 stars

y1621 Differential cover set for FG / Carson 2WD off-road cars
This two-piece differential cover is easy to attach with the existing screws and provides optimal protection against stones and dirt. Suitable for all 2WD FG Offroad models, not suitable for the 2WD models that are based on 4WD e.g. Fun Cross, Leopard, Truggy and all WB535 models.Also suitable for Carson 2WD models e.g. Uno, Attack, Gas Blaster and more.Contents:1 set

€19.90*

Alternatives

Average rating of 0 out of 5 stars

y1163 Aluminum differential case conversion kit for FG 2WD/4WD
Genuine HT spare/option part.Alloy diff case conversion kit for FG 2WD cars and 4WD large scale cars, fits front or rear axle. You need two sets to do a complete car.Comes complete as shown with sealed bearings, installed needle bearings, shims, screws and o-rings.Please note:The differential comes unassembled, we recommend assembly tool #8505 for bevel gear installation.Contents:1 piece

€89.90*

Average rating of 0 out of 5 stars

Fully assembled alloy diff incl. reinforced diff. tube and bevel diff. gearwheel for FG 2WD/4WD + Carson/Smartech 2WD
Genuine HT spare/option part. Fully assembled Alloy differential including reinforced differential-tube and "inner-workings", such as original planetary gears, differential bevel gears, bevel differential wheel axles, sealed bearings, differential shafts with needle bearings (high-speed needle bearing).You only have to insert your full-floating axle (halfshafts). Since the FG and Carson are having different internal teeths by the planetary gears, different versions for FG and Carson/Smartech 2WD are available.Even on heavy off-road use and especially on jumps there are often problems with the original plastic differential. Noticeable is also the relatively thin differential-tube of the serial-equipping. Therefore our special offer for the complete Alloy differential including extra reinforced differential-tube.Set includet:8486 Alloy differential housing6068 Bevel differential gear axle6066/01 Differential bevel gear A, spline drive 6067 Differential bevel gear BFG ball bearings, sealed, y19610-rsReinforced differential tube for FG buggy differential, y09028498/01 Needle bearing for alloy differentialContents:1 set

€189.90*

Average rating of 0 out of 5 stars

y0270 Alloy differential case conversion kit for FG 2WD models
Genuine HT spare/option part.Alloy case conversion kit for Smartech / Carson 2WD and FG 2WD large scale cars .Comes complete as shown with reinforced differential tube, sealed bearings, installed needle bearings, shims, screws and o-rings.The scope of supply for FG:4 x Countersunk screw M4 x 8 mm2 x Shims 8 x 20 x 0,10 mm2 x Lenticular flange head screw M3 x 10 mm2 x Washers 3,2 mm2 x Gasket for DiffThe scope of supply for Smartech:4 x Countersunk screw M4 x 8 mm4 x Shims 8 x 20 x 0,10 mm8 x Shims 5 x 17 x 0,10 mm2 x Lenticular flange head screw M3 x 10 mm2 x Washers 3,2 mm2 x Gasket for DiffContents:1 set

€99.90*

Average rating of 0 out of 5 stars

y1621 Differential cover set for FG / Carson 2WD off-road cars
This two-piece differential cover is easy to attach with the existing screws and provides optimal protection against stones and dirt. Suitable for all 2WD FG Offroad models, not suitable for the 2WD models that are based on 4WD e.g. Fun Cross, Leopard, Truggy and all WB535 models.Also suitable for Carson 2WD models e.g. Uno, Attack, Gas Blaster and more.Contents:1 set

€19.90*

Customers also bought

Average rating of 0 out of 5 stars

6068 FG Bevel differential gear axle
Genuine FG spare/option part. For non-adjustable FG differentials.Dimensions:Diameter: 5 mmLength: 40 mmContents:1 piece

€5.90*

Average rating of 0 out of 5 stars

6065/01 FG Plastic diff. cover
Original FG Ersatz-/Tuningteil.Well-priced but still effective plastic diff. cover. Stones can damage metal covers and it is difficult to removethem. According to the flexible plastic material an impressing becomes hardly possible. If it still happens the cover can be easily removed through cutting with a knife or a scissors.Dimensions:Length: 43 mmDiameter: 45 mmFlange diameter: 65 mmInhalt:1 Stück

€6.90*

Average rating of 0 out of 5 stars

- GWH04-XM3 GRP W04 REVO XM3 Tyres Hard
This pair of Tyres have the following use indications: VERY HIGH GRIP situation for very clean track. VERY HIGH GRIP situation for big asphalt. VERY HIGH GRIP situation for very high temperatures. This pair of Tyres have the following technical features: REVO treated profile for the maximum traction and the maximum lateral grip. Treated profile studied to maintain the tyre surface alway clean from rubber murble. Compound exclusively developped for model tyres. Inside belt flexible but very strong, vulcanized directly together with tyre compound. Insert foam with special material for high temperatures, for maximum stability and high drive precision. Spoked wheel moulded with special material for high temperatures for maximum grip and stability. Special gluing system 100% guaranteed.The main sizes for this tyre are: WHEEL fixing with square 18mm. TYRE outside diameter 118mm. WHEEL inside diameter 90mm. TYRE tota width 65mm. Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!

€38.90*

Average rating of 0 out of 5 stars

- GWH04-XM2 GRP W04 REVO XM2 Tyres Medium
This pair of Tyres have the following use indications: HIGH GRIP situation for clean track. HIGH GRIP situation for big asphalt. HIGH GRIP situation for high temperatures. This pair of Tyres have the following technical features: REVO treated profile for the maximum traction and the maximum lateral grip. Treated profile studied to maintain the tyre surface alway clean from rubber murble. Compound exclusively developped for model tyres. Inside belt flexible but very strong, vulcanized directly together with tyre compound. Insert foam with special material for high temperatures, for maximum stability and high drive precision. Spoked wheel moulded with special material for high temperatures for maximum grip and stability. Special gluing system 100% guaranteed.The main sizes for this tyre are: WHEEL fixing with square 18mm. TYRE outside diameter 118mm. WHEEL inside diameter 90mm. TYRE tota width 65mm. Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!

€38.90*

Average rating of 0 out of 5 stars

y1004 Driveshaft boots for ball drive + dogbones
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

Average rating of 0 out of 5 stars

6013 FG Body clips
Genuine FG spare/option part. Dimensions:Length: 33 mmWire diameter 1.5 mmContents:10 pieces

€4.95*

Similar products

Average rating of 0 out of 5 stars

6065/01 FG Plastic diff. cover
Original FG Ersatz-/Tuningteil.Well-priced but still effective plastic diff. cover. Stones can damage metal covers and it is difficult to removethem. According to the flexible plastic material an impressing becomes hardly possible. If it still happens the cover can be easily removed through cutting with a knife or a scissors.Dimensions:Length: 43 mmDiameter: 45 mmFlange diameter: 65 mmInhalt:1 Stück

€6.90*

Average rating of 0 out of 5 stars

6077/05 FG Steel ball 10x13mm for rear upright - 2pcs.
Steel ball for rear upright.5 mm bore diameter

€8.50*

Average rating of 0 out of 5 stars

6081/01 FG Steel ball Ø5mm 10x15 mm
Genuine FG spare/option part. Ball joint with 5mm bore suitable for all FG plastic ball-and-socket joints.Contents:4 pieces

€16.90*

Average rating of 0 out of 5 stars

6079/05 FG Ball driving axle M8
Original FG Ersatz-/Tuningteil.Inhalt:1 Stück

€35.90*

Average rating of 0 out of 5 stars

6069/01 FG Differential axle spline drive
Genuine FG spare/option part.For all FG cars with standard drive shafts (no ball drive). Accepts dogbones with 10 mm ball and 4 mm pin.Dimensions:Shaft, diameter: 8 mmLength: 27 mmSpline drive for FG bevel gearsCup, diameter: 18,5 mmLength 14 mmContents:1 piece

€27.90*

Average rating of 0 out of 5 stars

6077/08 FG Spacer bushing for rear upright
Genuine FG spare/option part. Only suitable with standard size ball bearings.Dimensions:Length: 10 mmOuter diameter: 11 mmInner diameter: 8 mmContents:2 pieces

€4.50*

Average rating of 0 out of 5 stars

6065 FG Differential tube
Genuine FG spare/option part. Stock aluminum differential tube with a wall thickness from 1 mm.Also available as a reinforced version.Dimensions:Length: 43 mmOuter diameter: 45 mmContents:1 piece

€11.90*

Average rating of 0 out of 5 stars

6076/01 FG Rear camber rod 61 mm
Genuine FG spare/option part. M8 turnbuckle.Contents:2 pieces

€13.90*

Average rating of 0 out of 5 stars

6073 FG Rear lower wishbone pin
Genuine FG spare/option part. Also available in titanium 4510 and hardened steel 6073/05.Dimensions:Diameter: 6 mmLength: 63 mmContents:2 pieces

€8.90*

Average rating of 0 out of 5 stars

6077/02 FG Screws M5x30 mm for rear uprights
Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Contents:4 pieces

€2.95*

Average rating of 0 out of 5 stars

6080 FG Rear dogbone
Genuine FG spare/option part. Replacement drive shaft (dogbone). Long Version.Suitable for BMW GTR, Mercedes CLK-GTR, Race-Trucks, C291, Porsche GT1, GT2, GT3 and all FG Off-Road models.Dimensions:Shaft diameter: 7 mmBall diameter: 10 mmLength: 101,5 mmContents:1 piece

€17.90*

Average rating of 0 out of 5 stars

6062 FG Rear diff mount right
Genuine FG spare/option part. Contents:1 piece

€12.90*

Customers also viewed

Average rating of 0 out of 5 stars

y1163 Aluminum differential case conversion kit for FG 2WD/4WD
y1163 Version: y1163/02 for 4WD models
Genuine HT spare/option part.Alloy diff case conversion kit for FG 2WD cars and 4WD large scale cars, fits front or rear axle. You need two sets to do a complete car.Comes complete as shown with sealed bearings, installed needle bearings, shims, screws and o-rings.Please note:The differential comes unassembled, we recommend assembly tool #8505 for bevel gear installation.Contents:1 piece

€89.90*

Average rating of 0 out of 5 stars

6065/01 FG Plastic diff. cover
Original FG Ersatz-/Tuningteil.Well-priced but still effective plastic diff. cover. Stones can damage metal covers and it is difficult to removethem. According to the flexible plastic material an impressing becomes hardly possible. If it still happens the cover can be easily removed through cutting with a knife or a scissors.Dimensions:Length: 43 mmDiameter: 45 mmFlange diameter: 65 mmInhalt:1 Stück

€6.90*

Average rating of 0 out of 5 stars

68405/01 FG Alloy differential 4WD conversion kit
Genuine FG spare/option part. Conversion kit for standard differential. Precise, solid and reliable, for use at competitions.Suitable for Off-Road Buggy 4WD RTR, Off-Road Beetle 4WD RTR and Monster/Stadium models 4WD RTR.Contents:1 set

€93.50*

Average rating of 0 out of 5 stars

67240 FG Alloy servo retainer, 2-parts, fixed, 2pcs.
Item N° 67240Alloy servo retainer, 2-parts, fixed, 2pcs.

€52.70*
%

Average rating of 0 out of 5 stars

Steel ball joint 4/6/8 mm to choose r/l thread, 3/4/5 mm bore in ball
Regular price: 9,70 EUROffer price: 4,90 EURy0529/01 - Steel ball joint 4 mm r/h or l/h thread, 3 mm bore in ball, for servo saver/servo and other applications.Set contents:One each with M4 right hand thread or one each M4 with left hand threadPlease note:We recommend using a nut 54374 for locking the r/h thread ball joint to prevent the linkage from loss of adjustment. y0529 - Steel ball joint 6 mm r/h or l/h thread, 4 mm bore in ballSteel ball joints 6 mm r/h or l/h thread, 4 mm bore in ball, for steering rods and other applications.Set contents:One each with M6 right hand thread or one each M6 with left hand threadPlease note:We recommend locking the ball joints using M6 low height nuts y0888 or y0889 to prevent the linkage from loss of adjustment. y0529/02 - Steel ball joints M8 r/h or l/h thread, 5 mm bore in ball One pieces of steel ball joints with 5 mm bore in ball and M8 r/h or l/h thread.Suitable for most every 1/5 and 1/6 car!Replaces FG plastic ball joints # 6029/08 and # 6081/01 in conjunction with the conical spacers # 4429/02.Replaces Smartech # 32409 and # 32446 as well.Please note:We recommend using a nut 4472/02 or 4472/03 for locking the thread ball joint to prevent the linkage from loss of adjustment.

€4.90* €9.90* (50.51% saved)

Average rating of 0 out of 5 stars

6065 FG Differential tube
Genuine FG spare/option part. Stock aluminum differential tube with a wall thickness from 1 mm.Also available as a reinforced version.Dimensions:Length: 43 mmOuter diameter: 45 mmContents:1 piece

€11.90*

Average rating of 0 out of 5 stars

6068 FG Bevel differential gear axle
Genuine FG spare/option part. For non-adjustable FG differentials.Dimensions:Diameter: 5 mmLength: 40 mmContents:1 piece

€5.90*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Agency