Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

6080 FG Rear dogbone

Product information "6080 FG Rear dogbone"

Genuine FG spare/option part.

Replacement drive shaft (dogbone). Long Version.

Suitable for BMW GTR, Mercedes CLK-GTR, Race-Trucks, C291, Porsche GT1, GT2, GT3 and all FG Off-Road models.

Dimensions:
  • Shaft diameter: 7 mm
  • Ball diameter: 10 mm
  • Length: 101,5 mm


Contents:
  • 1 piece

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Accessories / Spare parts

Average rating of 0 out of 5 stars

y1218 Springs for drive shafts
Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

€4.90*

Average rating of 0 out of 5 stars

y1004 Driveshaft boots for ball drive + dogbones
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

Average rating of 0 out of 5 stars

GPM 9472 Ball drive conversion kit for FG Marder, Off-Road, Beetle, Monster/Stadium, Formula 1 and Truck cars
Fits all FG offroad (like Marder, Off-Road Buggy, Beetle) / monster and stadium models (except Leopard 2010 up). Also for FG Formula 1 and Race Truck models.The ball drive conversion kit for FG touring cars and gt-models you will find here: GPM 9471. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM ball drive set includes everything for a conversion of the respective FG car. Set includes:Quantity:DescriptionPart number2 piecesBall drive wheel shaftGPM 6079/012 piecesDifferential ball drive cupGPM 6069/022 piecesBall drive shaft 96,5 mmGPM 6080/014 piecesDrive shaft booty100412 piecesSteel ballGPM 7080/024 piecesDrive shaft spacer springy1218

€149.90*

Average rating of 0 out of 5 stars

y0809 Klüber high performance grease for differentials
Freaking expensive, but it is damned fine.ASONIC HQ 72-102 is a synthetic high-temperature lubricating grease, for use in limited slip differentials. Due to the careful selection of product components and the clean manufacturing environment, ASONIC HQ 72-102 is a rolling bearing grease with a particularly low noise level.Benefits for your application:High-temperature lubricating grease for rolling bearingsHigh purityLow noiseGood water resistanceContent:1 piece, tube with 30g

Content: 30 Gramm (€730.00* / 1000 Gramm)

€21.90*

Alternatives

Average rating of 0 out of 5 stars

GPM 9472 Ball drive conversion kit for FG Marder, Off-Road, Beetle, Monster/Stadium, Formula 1 and Truck cars
Fits all FG offroad (like Marder, Off-Road Buggy, Beetle) / monster and stadium models (except Leopard 2010 up). Also for FG Formula 1 and Race Truck models.The ball drive conversion kit for FG touring cars and gt-models you will find here: GPM 9471. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM ball drive set includes everything for a conversion of the respective FG car. Set includes:Quantity:DescriptionPart number2 piecesBall drive wheel shaftGPM 6079/012 piecesDifferential ball drive cupGPM 6069/022 piecesBall drive shaft 96,5 mmGPM 6080/014 piecesDrive shaft booty100412 piecesSteel ballGPM 7080/024 piecesDrive shaft spacer springy1218

€149.90*

Average rating of 0 out of 5 stars

y1004 Driveshaft boots for ball drive + dogbones
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

Average rating of 0 out of 5 stars

y1218 Springs for drive shafts
Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

€4.90*

Average rating of 0 out of 5 stars

y0809 Klüber high performance grease for differentials
Freaking expensive, but it is damned fine.ASONIC HQ 72-102 is a synthetic high-temperature lubricating grease, for use in limited slip differentials. Due to the careful selection of product components and the clean manufacturing environment, ASONIC HQ 72-102 is a rolling bearing grease with a particularly low noise level.Benefits for your application:High-temperature lubricating grease for rolling bearingsHigh purityLow noiseGood water resistanceContent:1 piece, tube with 30g

Content: 30 Gramm (€730.00* / 1000 Gramm)

€21.90*

Customers also bought

Average rating of 0 out of 5 stars

6069/01 FG Differential axle spline drive
Genuine FG spare/option part.For all FG cars with standard drive shafts (no ball drive). Accepts dogbones with 10 mm ball and 4 mm pin.Dimensions:Shaft, diameter: 8 mmLength: 27 mmSpline drive for FG bevel gearsCup, diameter: 18,5 mmLength 14 mmContents:1 piece

€29.00*

Average rating of 0 out of 5 stars

6079 FG Rear axle shaft
Genuine FG spare/option part. Dimensions:Total length 73 mmLength of M6 thread section 11 mmLength of 8 mm shaft incl. thread 59 mmLength of drive cup 14 mmContents:1 piece

€31.90*

Average rating of 0 out of 5 stars

60210/06 FG Off-Road Buggy tires M wide glued, black
Genuine FG spare/option part. 1:/6 Off-Road Buggy tires, medium, glued on FG Off-Road buggy-rim black. Outer Ø 175 mm, width 80 mm, Suitable for the FG cars Marder, Off-Road Buggy, Beetle and Monster cars with 18 mm square wheel drive. Suitable for other 1/6 cars as well: please check the wheel drive regarding this matter. When the wheel change causes a significant change of the tire's outer diameter, adapting the gear ratio is recommended.Contents:2 pieces

€99.99*

Average rating of 0 out of 5 stars

6104 FG Front axle shaft, 55mm - 1pce.
Genuine FG spare/option part. Suitable for all FG models. Only useable with 9,5mm square driver.Diameter 8 mm.Contents:1 piece

€6.50*

Average rating of 0 out of 5 stars

8483/05 FG Alloy differential for 1:5 and 1:6
Genuine FG spare/option part. Alloy differential for 1:5 and 1:6 recommended for competitions. This differential is not adjustable but very solid because of its metal housing. The diff will delivery complete with bevel gears and ball bearings.The big gearwheel and the axle spline drive will not delivery!Content:1 set

€139.99*

Average rating of 0 out of 5 stars

6052 FG Plastic gearwheel 48 teeth
Genuine FG spare/option part. Stock spur gear for all FG monster cars.Suitable for spur gear carriers: 6050 (plastic) 6439 (aluminum)Dimensions:Diameter: 75 mmWidth: 15.5 mmTooth width: 12 mmModule: m=1,5 Contents:1 piece

€17.90*

Similar products

Average rating of 0 out of 5 stars

y1004 Driveshaft boots for ball drive + dogbones
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

Average rating of 0 out of 5 stars

6069/01 FG Differential axle spline drive
Genuine FG spare/option part.For all FG cars with standard drive shafts (no ball drive). Accepts dogbones with 10 mm ball and 4 mm pin.Dimensions:Shaft, diameter: 8 mmLength: 27 mmSpline drive for FG bevel gearsCup, diameter: 18,5 mmLength 14 mmContents:1 piece

€29.00*

Average rating of 0 out of 5 stars

68277 FG Front driveshaft 4WD
Genuine FG spare/option part.Dimensions:Diameter: 7,10 mmTotal length: 107,5 mmContents:1 piece

€17.50*

Average rating of 0 out of 5 stars

y1004/01 Driveshaft boots for ball drive and dogbones
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt.For FG and Carson ball drives, fits standard dogbones as well.Content10 pieces

€34.90*

Average rating of 0 out of 5 stars

67577 FG Drive shaft 134 mm
Genuine FG spare/option part. Please note: If you own a Leopard 2WD with the old 130.5 mm driveshafts (same part number), the upgrade of both shafts is recommended.Contents:1 piece

€19.90*

Average rating of 0 out of 5 stars

y67577 Drive shaft 132 mm
Genuine HT spare/option part. Dimensions:Total length: approx. 132 mmLength center pin / center pin: approx. 123 mmShaft diameter: approx. 6 mmBall diameter: approx. 9,8 mmPlease note:If you own a Leopard 2WD with the old 130.5 mm driveshafts, the swap of both shafts is recommended.Contents:1 piece

€9.90*

Average rating of 0 out of 5 stars

68276 FG Front wheel shaft 2WD/4WD
Genuine FG spare/option part. Diameter 8 mm.Contents:1 pieceFor older 2WD models that are not based on the 4WD models, please refer to Sportsline 2008. or if an RC plate is no longer fitted, check Sportsline 13 in Parts Scout.There you will find the right spare parts for your vehicle.

€19.90*

Average rating of 0 out of 5 stars

y1345 Drive pins, choice of sizes, e.g. for Losi, Mini and HPI cars
y1345 Size: y1345/04 - 5 x 24 mm
Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces

€4.90*

Average rating of 0 out of 5 stars

7080 FG Rear dogbone 90 mm
Genuine FG spare/option part. Standard driveshaft, short version.Fits FG Audi, BMW 320, Peugeot 307, Renault Megane und VW New Beetle.Dimensions:Shaft diameter: 7 mmBall diameter: 10 mmLength: 90 mmContents:1 piece

€23.90*

Average rating of 0 out of 5 stars

67576 FG Driving shaft 142 mm
Genuine FG spare/option part.Spare part for Sportsline Leopard 4WD.Contents:1 piece

€19.90*

Average rating of 0 out of 5 stars

7081 FG Rear dogbone 96 mm
Genuine FG spare/option part.Standard driveshaft, medium length. Fits BMW M3 GTR, Mercedes C-Klasse DTM 04, Mercedes CLK-DTM, McLaren GT, Honda Accord, Dogde Viper, Opel V8 und Porsche Carrera GT.Dimensions:Shaft diameter: 7 mmBall diameter: 10 mmLength: 96 mmContents:1 piece

€25.00*

Customers also viewed

Average rating of 0 out of 5 stars

68277 FG Front driveshaft 4WD
Genuine FG spare/option part.Dimensions:Diameter: 7,10 mmTotal length: 107,5 mmContents:1 piece

€17.50*

Average rating of 0 out of 5 stars

7081 FG Rear dogbone 96 mm
Genuine FG spare/option part.Standard driveshaft, medium length. Fits BMW M3 GTR, Mercedes C-Klasse DTM 04, Mercedes CLK-DTM, McLaren GT, Honda Accord, Dogde Viper, Opel V8 und Porsche Carrera GT.Dimensions:Shaft diameter: 7 mmBall diameter: 10 mmLength: 96 mmContents:1 piece

€25.00*

Average rating of 0 out of 5 stars

10009 FG Formula 1 Competition 1/5 "New Version2025"
Highlights News 2025 Tuning aluminium lower wishbones, one-piece (front and rear) Tuning chassis plate black anodised and milled Tuning milled aluminium rear axle linkage for toe-in adjustment  Perforated tuning clutch bell Side flaps on the rear spoiler in carbon fibre Highlights Formel 1 Competition- This model is fitted with numerous aluminium parts: - front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Technical description of the FG Formula 1 Competition :The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with tuning bowden cable brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition CNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ Zenoah engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, mechanical Tuning brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos (each approx. 40 - 50 kg), 2 servo for throttle brake (approx. 20 - 30 kg), batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engineAirboxPipe Clear bodyshell and polycarbonate spoiler Mechanical brakesDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!

€2,699.50*

Average rating of 0 out of 5 stars

6722/30 FG Countersunk screw M5x30 mm, 10 pieces
Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:10 pieces

€5.50*

Average rating of 0 out of 5 stars

2009-30 Mecatech Klick-Shock o-ring
Genuine Mecatech spare/option part.Contents:2 pieces

€3.25*

Average rating of 0 out of 5 stars

67275/05 FG Universal joint f. front axle Leo 4 Comp., M8, compl., 1 pce.
Genuine FG spare/option part.With reinforced M8 connection thread. Solid universal joints made of hardened, high-quality steel for the front axle of the Leo 4 Competition. With ball drive and ball diff. axle. The model has a higher steering deflection and a smoother driving performance in curves if you mount this universal joint. Replaces universal joint 67275. For mounting you need additionally the self-locking wheel nuts M8 Item N°. 6115.

€77.95*
%

Average rating of 0 out of 5 stars

y1034 HT Aluminum front suspension for FG Off-Road Buggy 2WD, set
The sets include complete front bulkheads A + B with brace, upper (adjustable) and lower a-arms and shock tower.Please note: the hinge pins are not included, you will use the pins from the stock suspension!The sets include:Item N°Name:y1027HT Aluminum a-arm 2WD, front uppery1026HT Aluminum a-arm 2WD, front lower, one-piecey1028HT Aluminum front bulkhead A for 2WDy1030HT Aluminum front bulkhead B for 2WDy1036HT rose joints with conical spacersy1029HT aluminum droop stopsy1035HT Aluminum shock tower Off-Road Buggy 2WDy1031HT Aluminum bulkhead brace for 2WDUnit prices: 387,10 EURFits FG Off-Road Buggy 2WD.This front suspension can be used on a FG Monster Beetl 2WD as well, however some new holes must be drilled into the shock tower for this application.

€339.00* €387.10* (12.43% saved)
Loading...
Upload in progress, please be patient ...
Shopware-Theme Development Shopware-Agency