6079 FG Rear axle shaft

€31.90*

Prices incl. VAT plus shipping costs

Available

Product number: fg_6079

EAN: 3410564505915

Product information "6079 FG Rear axle shaft"

Genuine FG spare/option part.

Dimensions:

Total length 73 mm
Length of M6 thread section 11 mm
Length of 8 mm shaft incl. thread 59 mm
Length of drive cup 14 mm

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Accessories / Spare parts

y1218 Springs for drive shafts

Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

€4.90*

y1004 Driveshaft boots for ball drive + dogbones

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

y0809 Klüber high performance grease for differentials

Freaking expensive, but it is damned fine.ASONIC HQ 72-102 is a synthetic high-temperature lubricating grease, for use in limited slip differentials. Due to the careful selection of product components and the clean manufacturing environment, ASONIC HQ 72-102 is a rolling bearing grease with a particularly low noise level.Benefits for your application:High-temperature lubricating grease for rolling bearingsHigh purityLow noiseGood water resistanceContent:1 piece, tube with 30g

Content: 30 Gramm (€730.00* / 1000 Gramm)

€21.90*

Alternatives

GPM 9472 Ball drive conversion kit for FG Marder, Off-Road, Beetle, Monster/Stadium, Formula 1 and Truck cars

Fits all FG offroad (like Marder, Off-Road Buggy, Beetle) / monster and stadium models (except Leopard 2010 up). Also for FG Formula 1 and Race Truck models.The ball drive conversion kit for FG touring cars and gt-models you will find here: GPM 9471. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM ball drive set includes everything for a conversion of the respective FG car. Set includes:Quantity:DescriptionPart number2 piecesBall drive wheel shaftGPM 6079/012 piecesDifferential ball drive cupGPM 6069/022 piecesBall drive shaft 96,5 mmGPM 6080/014 piecesDrive shaft booty100412 piecesSteel ballGPM 7080/024 piecesDrive shaft spacer springy1218

€149.90*

y1004 Driveshaft boots for ball drive + dogbones

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

y1218 Springs for drive shafts

€4.90*

y0809 Klüber high performance grease for differentials

Content: 30 Gramm (€730.00* / 1000 Gramm)

€21.90*

Customers also viewed

10269 FG Team decals Buzzin-Hornets Formula 1

Genuine FG spare/option part.Measures:475 x 360 mm475 x 320 mm345 x 160 mm

€28.80*

6079/05 FG Ball driving axle M8

Original FG Ersatz-/Tuningteil.Inhalt:1 Stück

€32.95*

DYNE1240 Dynamite Large Scale Safety Kill Switch

Genuine Dynamite spare/option part.Key Features:Kills your 2-cycle gas engine on command, loss of radio signal, low battery, or total battery power lossComes ready to install no soldering requiredOptically Coupled to isolate your ignition system from your radio systemBuilt-in LED for easy-to-spot operational status3-Channel Radio System RequiredNot Compatible with AVC-Equipped ReceiversContents:1 piece

€39.99*

Details

GPM 7081/01 Ball driveshaft for 91 mm FG and Mecatech cars, 1 pce.

Fits all FG and Mecatech touring cars and gt-models. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins. The GPM ball drives can be partially mixed with FG parts. The heads of the GPM driveshafts fit into FG differential cups or wheel shafts.The opposite combination, i.e. FG shafts in GPM differential cups or wheel shafts does not always fit. We had tests where some FG shafts fit neatly, but due to slight tolerances others who did not fit into the very same cups/shafts. For this combination, we can not guarantee compatibility! Dimensions: Length 91 mm

From €19.80*

Details

y1525 Universal screws/nuts/washer set for all FG vehicles

Complete universal set of screws, nuts and washers for all 1/5 and 1/6 scale FG vehicles (except Competition/Evo alloy models).The set includes a total of 309 screws, nuts and washers in different quantities.13 sizes of cap head screws8 sizes of CSH screws3 sizes of button head screws7 sizes of set screws6 sizes of washers3 sizes of self-locking nuts2 sizes of nuts9 sizes of self tapping screws3 sizes of CSH self tapping screws3 sizes of pan head screwsComes in a high quality 190x170x40 mm assortment box.Contents:Cap head screws in 12.9:3 piecesM3x82 piecesM3x161 piecesM3x183 piecesM3x209 piecesM4x202 piecesM4x252 piecesM4x301 piecesM4x451 piecesM5x162 piecesM5x251 piecesM6x103 piecesM6x401 piecesM6x75CSH screws in 10.9:2 piecesM4x162 piecesM4x258 piecesM4x401 piecesM5x142 piecesM5x256 piecesM5x302 piecesM5x351 piecesM6x16Button head screws in 10.9:10 piecesM4x82 piecesM4x142 piecesM5x40Grub screws:2 piecesM4x305 piecesM5x52 piecesM5x164 piecesM5x252 piecesM5x302 piecesM5x408 piecesM6x6Washers:2 piecesM3,2510 piecesM4,215 piecesM5,33 piecesM6,410 piecesM4,23 pieces10x16x1Self-locking nuts:3 piecesM316 piecesM410 piecesM5Normal nuts:8 piecesM54 piecesM5Sheet metal screws DIN 7981 Torx:7 piecesM2,9x9,52 piecesM2,9x131 piecesM2,9x192 piecesM2,9x226 piecesM4,2x9,59 piecesM4,2x1314 piecesM4,2x1614 piecesM4,2x225 piecesM4,2x32Countersunk head senk sheet metal screws DIN7982 Torx:14 piecesM4,2x1348 piecesM4,2x162 piecesM4,2x32Button head screws DIN 7985 Phillips (Kreuzschlitz) Verz. 4.8:4 piecesM3x41 piecesM3x252 piecesM4x14

€39.90*

4412 FG Driveshaft boots

Genuine FG spare/option part. Suitable for all FG models and other. To complete one car you need two sets.For 2WD models you need two sets and for 4WD models you need four sets.Contents:2 pieces

€19.90*

8610/10, FG Front axle w/h collar/ Square wheel driver 14 mm, set

Suitable for all FG front uprights. The use of this front axle prevents a pressing and jamming of the inner ball bearing rings when tightening the wheel. Suitable for square wheel driver 9,5mm and 14mm.

€29.90*