6077/08 FG Spacer bushing for rear upright
€4.90
Available
Product information "6077/08 FG Spacer bushing for rear upright"
Only suitable with standard size ball bearings.
Dimensions:
- Length: 10 mm
- Outer diameter: 11 mm
- Inner diameter: 8 mm
Contents:
- 2 pieces
Lebacher Strasse 4
66113 Saarbrücken
Germany
Login
Customers also bought
Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece
Genuine FG spare/option part. Fits FG + Carson 6 mm a-arm hinge pins and 8 mm front wheel shafts.Part is delivered in silver or black color from vendor!Content:15 pieces
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt.For FG and Carson ball drives, fits standard dogbones as well.Content10 pieces
Genuine FG spare/option part. Screw tap to cut new thread borings and to recut defective ones.Contents:1 piece
Original FG Ersatz-/Tuningteil.Screw tap to cut new thread borings and to recut defective ones.Inhalt:1 Stück
Customers also viewed
Genuine FG spare/option part. These lug nuts ensure that you will never again lose a tire while driving. They are installed onto the axle shaft and secured by a set screw which goes through the wheel nut, tightened into the rim. This makes it almost impossible to lose such a wheel nut.Part is delivered in silver or black color from vendor!Contents:4 pieces
Genuine FG spare/option part.The installation of these spacer bushings between the ball bearings in the uprights allows you to tighten the wheel nut strongly. Suitable for all FG plastic and alloy uprights.Dimensions:Outer diameter: 11 mmWidth: 7 mmInner diameter 8,22 mmContents:2 pieces
Genuine FG spare/option part. Suitable for all FG models and other. To complete one car you need two sets.For 2WD models you need two sets and for 4WD models you need four sets.Contents:2 pieces
Genuine FG spare/option part. Fits all FG 1/6 off road cars, alloy version.Length of threaded section approx. 17 mm.Contents:2 pieces
Genuine FG spare/option part.Splash water proofed ball bearings for front and rear uprights. Wheel bearing suitable for all FG and Carson models.Contents:2 pieces
Genuine FG spare/option part. Fits FG + Carson 6 mm a-arm hinge pins and 8 mm front wheel shafts.Part is delivered in silver or black color from vendor!Content:15 pieces
Genuine FG spare/option part. Corrosion resistant and 40 % less weight compared to steel.Contents:2 pieces