y0109 Universal radio plate for FG 1/6 2WD
€99.90
Available
Product information "y0109 Universal radio plate for FG 1/6 2WD"
Universal radio plate for FG 2WD Marder/Beetle/Off-Road Buggy/Pajero an all Monster and Stadium models.
With drilling templates for the following steering servos:
- Hitec HS-805BB/HS-5745/5735/Orange Power
- MPX Jumbo und Rhino
The size of the steering servo can vary because you can adjust the position of the aluminum tray bar to accomodate larger or smaller servos. You will need FG adapters for installation of the gas / brake servo: #5014/04 servo mounting frame for (standard sized) Futaba / JR, Thunder Tiger DS1015 - 2pcs.
Accepts FG servo frames for up to two throttle/brake servos (not included). Spacers for rx-box installation are included.
Old version chassis plates (~pre 2003) have a different bolt pattern. When installing this radio plate on an old chassis new mounting holes must be drilled into the chassis plate
The surface is plain aluminum. With the necessary effort it can be polished to a high luster.
Contents:
- 1 piece
Login
Accessories / Spare parts
Genuine FG spare/option part. Suitable for rc-plate 5014.Dimensions:Inside length: 44 mmInside width: 20,5 mmContents:2 pieces
Item N° 6534/02 Throttle pivot post 3.1mm - setRevised set for 2 mm linkages, but with 3.1 mm pivot bore to prevent linkage seizing. Can be used for throttle or brake applications.Set collars have 2.1 mm inner diameter.
Genuine FG spare/option part. Splash-proofed receiver box for all merchantable small receivers, suitable for all car models 1:12 - 1:5.Dimensions:Length: upper section 92 mm, bottom 69 mmHeight: 48 mmWidth: 38 mmContents:1 piece
Genuine FG spare/option part.Plastic bolt for battery holder.Contents:2 pieces
Customers also bought
Genuine FG spare/option part. Suitable for rc-plate 5014.Dimensions:Inside length: 44 mmInside width: 20,5 mmContents:2 pieces
Genuine HT spare/option part.Alloy case conversion kit for Smartech / Carson 2WD and FG 2WD large scale cars .Comes complete as shown with reinforced differential tube, sealed bearings, installed needle bearings, shims, screws and o-rings.The scope of supply for FG:4 x Countersunk screw M4 x 8 mm2 x Shims 8 x 20 x 0,10 mm2 x Lenticular flange head screw M3 x 10 mm2 x Washers 3,2 mm2 x Gasket for DiffThe scope of supply for Smartech:4 x Countersunk screw M4 x 8 mm4 x Shims 8 x 20 x 0,10 mm8 x Shims 5 x 17 x 0,10 mm2 x Lenticular flange head screw M3 x 10 mm2 x Washers 3,2 mm2 x Gasket for DiffContents:1 set
Genuine HT spare/option part.Fits Marder, Beetle, Pajero and Monster Beetle,Material thickness:6 mmContents:1 piece
Item N° 6567Cable hook-and-loop tape, 2pcs.
Genuine FG spare/option part. The differential key prevents a damage of the diff. cover through bigger stones. Suitable for all FG 1:6 Buggy and Monster models.Contents:1 piece
Genuine FG spare/option part. Suitable for all FG 2WD Off-Road models. Not suitable for Monster-Truck models.Bearing seats 22x7 mm.Contents:1 set
Customers also viewed
Universal radio plate, accepts the same servos as described under, but with a layout to fit FG Leopard and all onroad cars except EVO4 and Formula 1.You will need FG mounting frames for installation of the brake/thottle servo(s), the frames are not included.With drilling templates for the following steering servos:Hitec HS-805BB/HS-5745/5735/Orange PowerMPX Jumbo und RhinoThe surface is plain aluminum. With the necessary effort it can be polished to a high luster.
Genuine FG spare/option part. Suitable for rc-plate 5014.Dimensions:Inside length: 44 mmInside width: 20,5 mmContents:2 pieces
Genuine FG spare/option part. Individual prices of the parts in the tuning set: 847,06 EurosAluminum conversion kit to aluminum front axle and aluminum rear knuckle and wishbone for FG Marder.Contents:1 set
Genuine FG spare/option part. For use with hydraulic brakes.Contents:1 piece
Genuine FG spare/option part. Fits FG 2WD Marder.Offer your Marder a new life - it will be out of all recognition! Aggressive in the curves, dead on the line - just everything which guarantees pure driving fun. The well-tried 4WD by FG is now available as conversion kit for your 2WD Marder. You will not realize from the outside that the model is equipped with a fourwheel drive. But you and your rc-car friends will notice it considerably as soon as you start your model and speed up properly.The conversion kit includes all parts necessary to convert your 2WD Marder to a 4WD Buggy. A mounting instruction is enclosed.Please note: the radio plate is designed to accept a 805-sized servo (case length 65 mm). For installation of a Rhino (case length 58 mm) or a similar sized servo you need to order radioplate 68241 separately.Contents:1 set
Genuine HT spare/option part. Universal radio plate for FG 4WD Marder; Off-Road Buggy; Beetle and all 4WD Monster and Stadium Modelle. Optional for one or two servos.With drilling templates for up to two of the following steering servos:Big Scale Servo:Orange PowerHitec Servos:HS-805BB/MGHS-5745HS-5755FG Servos:65956596/li>Multiplex Servos:Jumbo´sRhinoCarson Servos:Mega EvoMega Evo ProAnd for all servos with the from 59x29x55 mm, 66x30x70mm. Parts like servos and decoration are not included! Spacers for throttle/brake servo (standard size) and rx-box are included.Delivery contents:Servo plateMountin boltsSpacerScrews and mounting materialThe surface is plain aluminum. With the necessary effort it can be polished to a high luster.