6479 FG Rear alloy uprights 08
€109.50
Currently unavailable
Product information "6479 FG Rear alloy uprights 08"
Content:
- Bearing seats: 22 x 7 mm
- Hinge pin bore: 6 mm
- Distance wheel shaft/hinge pin: 25 mm
Login
Accessories / Spare parts
Item N° 6479/01Rear alloy 08 upright, left, 1 pce.Spare part for FG no. 6479.
Item N° 6479/02Rear alloy 08 upright, right, 1 pce.Spare part for FG no. 6479.
Customers also bought
Genuine FG spare/option part. Machined alloy front uprights with replaceable steering arm, accept 608 sized bearings (8 x 22 x 7 mm, stock size). Fits all FG (except 4wd models) and Carson / Smartech 2WD 1/5 and 1/6 cars.included in delivery contents:4 x M5 x mm screws8 x M3 x mm screws8 x M5 x mm washerFor installation in offroad cars you will need shorter steering rods 7028/01.Contents:2 pieces
Genuine HT spare/option part. Universal radio plate for FG 2WD Marder/Beetle/Off-Road Buggy/Pajero an all Monster and Stadium models. With drilling templates for the following steering servos:Hitec HS-805BB/HS-5745/5735/Orange Power MPX Jumbo und Rhino The size of the steering servo can vary because you can adjust the position of the aluminum tray bar to accomodate larger or smaller servos. You will need FG adapters for installation of the gas / brake servo: #5014/04 servo mounting frame for (standard sized) Futaba / JR, Thunder Tiger DS1015 - 2pcs. Accepts FG servo frames for up to two throttle/brake servos (not included). Spacers for rx-box installation are included.Old version chassis plates (~pre 2003) have a different bolt pattern. When installing this radio plate on an old chassis new mounting holes must be drilled into the chassis plateThe surface is plain aluminum. With the necessary effort it can be polished to a high luster.Contents:1 piece
Genuine FG spare/option part. Suitable for rc-plate 5014.Dimensions:Inside length: 44 mmInside width: 20,5 mmContents:2 pieces
Genuine HT spare/option part.Alloy case conversion kit for Smartech / Carson 2WD and FG 2WD large scale cars .Comes complete as shown with reinforced differential tube, sealed bearings, installed needle bearings, shims, screws and o-rings.The scope of supply for FG:4 x Countersunk screw M4 x 8 mm2 x Shims 8 x 20 x 0,10 mm2 x Lenticular flange head screw M3 x 10 mm2 x Washers 3,2 mm2 x Gasket for DiffThe scope of supply for Smartech:4 x Countersunk screw M4 x 8 mm4 x Shims 8 x 20 x 0,10 mm8 x Shims 5 x 17 x 0,10 mm2 x Lenticular flange head screw M3 x 10 mm2 x Washers 3,2 mm2 x Gasket for DiffContents:1 set
Genuine HT spare/option part.Fits Marder, Beetle, Pajero and Monster Beetle,Material thickness:6 mmContents:1 piece
Item N° 6567Cable hook-and-loop tape, 2pcs.
Customers also viewed
Genuine HT spare/option part. Rear alloy uprights for 1:5 and 1:6 models and 4WD Porsche, CNC-cut, optimal fitting, non-twisting even by heat.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 20 mmContents:1 set
Genuine HT spare/option part.New designed rear lower alloy wishbone with replaceable guide bushes.Suitable for all FG 1:5 models with a width up to 400mm.Does also fit Carson Attack and Super Attack (not Evo!), C5, Smartech Spider and Ranger cars; also for Reely R5 and Big Pyro when used in combination with turnbuckle 6100/04.Please note: must use hinge pins 6075 instead of 6073!Scope of delivery:1x Alloy wishbone1x Socket head cap screw: 4 x 20 mm1x Socket head cap screw: 3 x 14 mm1x Socket head cap screw: 4 x 25 mm1x Washers steel 4,3 mm1x self-locking hexagon nut M42x hex nut M8 l/h thread4x Bearings with flangeContents:1 piece
Genuine FG spare/option part. Contents:1 piece / 50 ml
Content: 50 Milliliter (€198.00 / 1000 Milliliter)
Genuine HT spare/option part.Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.Comes with adjustment clips and grub screws for the hinge pins included.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm Contents:2 pieces
Genuine HT spare/option part.Rear upper alloy wishbone with droop stop. Replacement for plastic wishbone FG 6074/02.Will also fit the following Carson/Smartech cars:Onroad chassis C5, Attack, Super Attack, Gas Blaster and TouaregCarson Comanche, Attack Evo, CRT + CPT when installedwith 75 mm turnbuckle y0988Comes with 2 M8 low height nuts included. Contents:2 pieces
Spare part for 6478Bearing seats 22 x 7 mmHinge pin bore 6 mmDistance wheel shaft/hinge pin 25 mm
Alloy rear uprights, with replaceable hinge pin bushings.Fits FG and Carson/Smartech Attack, Attack Evo, Gas Blaster, Gas Devil, Super Attack, CRT, CRT 4x4, CPT, Uno, Monster Truck, Pick Up, Beetle and C5.The bearing bushings and bearings should be glued in place, as they have minimal play.One each lefthand and righthand version.Please note: for the installation of all popular disc brakes, we recommend: y6479