6103/05 FG Alloy upright front 1:6 2WD

€69.99*

Available

Product number: fg_6103_05

EAN: 3410564506301

Product information "6103/05 FG Alloy upright front 1:6 2WD"

Genuine FG spare/option part.

Suitable for all FG 2WD Off-Road models. Not suitable for Monster-Truck models.

Bearing seats 22x7 mm.

Contents:

1 set

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Accessories / Spare parts

6103/02 FG Screw M5x25 mm for front upright

Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Contents:6 pieces

€3.00*

6103/07 FG Alloy steering lever with stopper for 1:6

Genuine FG spare/option part. Spare part for 6103/05.Contents:1 set

€19.90*

Customers also bought

6078/06 FG ball bearing 8 x 22 x 7 sealed

Genuine FG spare/option part.Splash water proofed ball bearings for front and rear uprights. Wheel bearing suitable for all FG and Carson models.Contents:2 pieces

€13.90*

y0109 Universal radio plate for FG 1/6 2WD

Genuine HT spare/option part. Universal radio plate for FG 2WD Marder/Beetle/Off-Road Buggy/Pajero an all Monster and Stadium models. With drilling templates for the following steering servos:Hitec HS-805BB/HS-5745/5735/Orange Power MPX Jumbo und Rhino The size of the steering servo can vary because you can adjust the position of the aluminum tray bar to accomodate larger or smaller servos. You will need FG adapters for installation of the gas / brake servo: #5014/04 servo mounting frame for (standard sized) Futaba / JR, Thunder Tiger DS1015 - 2pcs. Accepts FG servo frames for up to two throttle/brake servos (not included). Spacers for rx-box installation are included.Old version chassis plates (~pre 2003) have a different bolt pattern. When installing this radio plate on an old chassis new mounting holes must be drilled into the chassis plateThe surface is plain aluminum. With the necessary effort it can be polished to a high luster.Contents:1 piece

€99.90*

5014/04 FG Servo adapter frame, Futaba/JR, Thunder Tiger DS1015

Genuine FG spare/option part. Suitable for rc-plate 5014.Dimensions:Inside length: 44 mmInside width: 20,5 mmContents:2 pieces

€12.90*

Details

y0270 Alloy differential case conversion kit for FG 2WD models

alu_diff_umbau Application: y0270/02 FG

Genuine HT spare/option part.Alloy case conversion kit for Smartech / Carson 2WD and FG 2WD large scale cars .Comes complete as shown with reinforced differential tube, sealed bearings, installed needle bearings, shims, screws and o-rings.The scope of supply for FG:4 x Countersunk screw M4 x 8 mm2 x Shims 8 x 20 x 0,10 mm2 x Lenticular flange head screw M3 x 10 mm2 x Washers 3,2 mm2 x Gasket for DiffThe scope of supply for Smartech:4 x Countersunk screw M4 x 8 mm4 x Shims 8 x 20 x 0,10 mm8 x Shims 5 x 17 x 0,10 mm2 x Lenticular flange head screw M3 x 10 mm2 x Washers 3,2 mm2 x Gasket for DiffContents:1 set

€99.90*

y1032 HT Aluminum shock tower Marder 2WD

Genuine HT spare/option part.Fits Marder, Beetle, Pajero and Monster Beetle,Material thickness:6 mmContents:1 piece

€47.90*

6567 FG Cable hook-and-loop tape, 2 pcs.

Item N° 6567Cable hook-and-loop tape, 2pcs.

€13.90*

Similar products

y1036 HT rose joints with conical spacers

Genuine HT spare/option part. Dimensions:A = 5 mmB = 6 mmC = 8 mmD = 13 mmContents:2 pieces rose joints4 pieces conical spacers

€24.90*

y6107 Wheel squares 18 mm HART-COAT, 9,5 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€14.95*

y6107/01 Wheel squares 18 mm HART-COAT, 14 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€17.45*

y6107/02 Wheel squares 18 mm HART-COAT, 17 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€18.95*

y6107/07 Wheel squares 18 mm HART-COAT, 12 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces

€16.45*

y0932 HT Alloy front uprights for FG / Smartech

Genuine FG spare/option part. Machined alloy front uprights with replaceable steering arm, accept 608 sized bearings (8 x 22 x 7 mm, stock size). Fits all FG (except 4wd models) and Carson / Smartech 2WD 1/5 and 1/6 cars.included in delivery contents:4 x M5 x mm screws8 x M3 x mm screws8 x M5 x mm washerFor installation in offroad cars you will need shorter steering rods 7028/01.Contents:2 pieces

€129.90*

y0264 C-clips with handle 4 - 6 mm

clipse_griff Size: y0264/05 - 5 mm

Genuine HT spare/option part.Quick change clips for installation and de-installation without tools, galvanic zinc plated.Spring steel, hardened and tempered to 1450 to 1600 N/mm² tensile strength.Available for 4, 5 and 6 mm shafts.Contents:10 pieces

€4.90*

y1345 Drive pins, choice of sizes, e.g. for Losi, Mini and HPI cars

y1345 Size: y1345/04 - 5 x 24 mm

Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces

€4.90*