Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

7425 FG Plastic gearwheel 39 teeth - 1pce.

Product information "7425 FG Plastic gearwheel 39 teeth - 1pce."

Suitable for all 1:5 models.
Diameter 63 mm
Width 15.5 mm
Tooth width 12 mm
Module: m=1,5

Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Accessories / Spare parts

Average rating of 0 out of 5 stars

y1426 HT aluminum gear carrier -on-road- with steel spur gear for the layshaft
Fits FG and Smartech touring cars. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions. The following measures are required for installation of the HT-steel gear adapter "on-road" on the layshaft in FG EVO 2020 cars:- The installed wide 16T layshaft pinion 6431/01 must be replaced by the narrow version 6431.- The supplied 1mm shim must be added between layshaft pinion and ball bearing.- The flat sections on the layshaft do not have the usual 180° offset for the adapter; therefore only one grub screw will be used. However, since this is a wide face M8 version, this is no disadvantage.

€69.90*

Alternatives

Average rating of 0 out of 5 stars

y1426 HT aluminum gear carrier -on-road- with steel spur gear for the layshaft
Fits FG and Smartech touring cars. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions. The following measures are required for installation of the HT-steel gear adapter "on-road" on the layshaft in FG EVO 2020 cars:- The installed wide 16T layshaft pinion 6431/01 must be replaced by the narrow version 6431.- The supplied 1mm shim must be added between layshaft pinion and ball bearing.- The flat sections on the layshaft do not have the usual 180° offset for the adapter; therefore only one grub screw will be used. However, since this is a wide face M8 version, this is no disadvantage.

€69.90*

Average rating of 0 out of 5 stars

7429 FG Plastic gearwheel 41 teeth - 1pce.
Suitable for all 1:5 models. With 63 mm diameter.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

€18.90*

Average rating of 0 out of 5 stars

7427 FG Plastic gearwheel 40 teeth
Genuine FG spare/option part.Suitable for all 1:5 models.Dimensions:Diameter 63 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5Contents:1 piece

€18.90*

Customers also bought

Average rating of 0 out of 5 stars

- GWH04-XM3 GRP W04 REVO XM3 Tyres Hard
This pair of Tyres have the following use indications: VERY HIGH GRIP situation for very clean track. VERY HIGH GRIP situation for big asphalt. VERY HIGH GRIP situation for very high temperatures. This pair of Tyres have the following technical features: REVO treated profile for the maximum traction and the maximum lateral grip. Treated profile studied to maintain the tyre surface alway clean from rubber murble. Compound exclusively developped for model tyres. Inside belt flexible but very strong, vulcanized directly together with tyre compound. Insert foam with special material for high temperatures, for maximum stability and high drive precision. Spoked wheel moulded with special material for high temperatures for maximum grip and stability. Special gluing system 100% guaranteed.The main sizes for this tyre are: WHEEL fixing with square 18mm. TYRE outside diameter 118mm. WHEEL inside diameter 90mm. TYRE tota width 65mm. Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!

€38.90*

Average rating of 0 out of 5 stars

7573/01 FG Receiver 2,4 GHz for FG-RS3
Genuine FG spare/option part. Contents:1 piece

€42.40*

Average rating of 0 out of 5 stars

y0663 Sanyo eneloop XX receiver battery 2500 mAh NiMh, 1 pce.
y0663 Connector: y0663/02 Futaba, JR, MPX universal
Item N° y0663Sanyo eneloop XX receiver battery 2500 mAh NiMh, 1 pce.Informations about eneloop cells:eneloop XXThe Sanyo eneloop cell eliminates the annoying problem that a charged battery has often lost a high percentage of its storage capacity after just one week. Also, the differences between individual cells in a pack are sometimes significant, reducing the life and performance of the complete pack. Compared to "normal" NiMh cells the Sanyo eneloop cell has a slightly lower capacity and a slightly higher price (in relationship to its capacity), but you get significant advantages in return. With the recently available improved version of the 2005 introduced and widely acclaimed eneloop cell self-discharge for rc-car related time frames is now more or less nonexistent. One could easily charge the cells at New Year?s Eve and use them at Christmas without noticing a significant loss of capacity. Sanyo eneloop cells show a considerably reduced tendency to failure of individual cells in a battery pack. Even after years eneloop cells usually differ by only a few percent. The voltage of the cells is also slightly higher than with normal NiMh cells, so that more volts are available under load. Especially when used in largescale cars with their usually extremely strong servos, this is a particularly important feature! Chargers which are suitable for NiMh cells will also work for eneloop cells. UniversalFGBECHigh currentThe basic features of the eneloop XX version are similar to the standard version, but here the priorities were set slightly different. At the expense of reduced (but easy to cope with for rc-car usage) values for load cycles and self-discharge, capacity could be increased by 25%.- Nominal capacity: 2500 mAh- Maximum number of charge cycles: 500- For cars with up to 3 servos- self-discharge: 25% at 1 yearYou can differentiate the two generations of eneloop cells by checking the model name which is written on each eneloop. The "old" cells have written HR-3UTG (AA) on them, the improved eneloop instead HR-3UTGA (AA)!

€39.90*

Average rating of 0 out of 5 stars

1000-04 Mecatech dust seal, 2 pcs.
Replacement part for Mecatech twin piston hydraulic brake.

€4.90*

Average rating of 0 out of 5 stars

7316 FG Clutch blocks for Zenoah
Genuine FG spare/option part. Zenoah bolts 7318 are required for installation.Content:2 pieces

€27.90*

Average rating of 0 out of 5 stars

8459/01 FG Brake shaft - 2pcs.
Spare part for , , , , , , , , , , and .

€27.90*

Similar products

Average rating of 0 out of 5 stars

7427 FG Plastic gearwheel 40 teeth
Genuine FG spare/option part.Suitable for all 1:5 models.Dimensions:Diameter 63 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5Contents:1 piece

€18.90*

Average rating of 0 out of 5 stars

6427 FG Plastic gear wheel 46 teeth - 1pce.
46 teeth gear wheel for the layshaft.Diameter 72 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€17.90*

Average rating of 0 out of 5 stars

7052 FG Plastic gear wheel 42 teeth - 1pce.
Gearwheel with 42 teeth for the layshaft. Diameter 66 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€17.50*

Average rating of 0 out of 5 stars

6052 FG Plastic gearwheel 48 teeth
Genuine FG spare/option part. Stock spur gear for all FG monster cars.Suitable for spur gear carriers: 6050 (plastic) 6439 (aluminum)Dimensions:Diameter: 75 mmWidth: 15.5 mmTooth width: 12 mmModule: m=1,5 Contents:1 piece

€17.90*

Average rating of 0 out of 5 stars

6422 FG Plastic gearwheel 44 teeth - 1pce.
44 teeth plastic main gear for the layshaft.Diameter 69 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€17.90*

Average rating of 0 out of 5 stars

7427/01 FG Plastic gearwheel 40 teeth 2-speed - 1pce.
Suitable for all 1:5 models with 2-speed gear.Diameter 63 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€18.90*

Average rating of 0 out of 5 stars

7424 FG Plastic gearwheel 38 teeth
Genuine FG spare/option part.Suitable for all 1:5 models. Requires gear carrier 7423.Dimensions:Diameter: 60 mmWidth: 15,5 mmTooth width: 12 mmModule: m=1,5Contents:1 piece

€17.90*

Average rating of 0 out of 5 stars

y0119 Steel pinion 16 teeth
Steel pinion 16 teeth suitable for 46 mm main gear for FG models.Modul 1,5

€29.90*

Average rating of 0 out of 5 stars

7052/01 FG Plastic gear wheel 42 teeth 2-speed
Genuine FG spare/option part. Gearwheel with 42 teeth for the layshaft. Only for the 2 speed box.Dimensions:Diameter: 66 mmWidth: 15,5 mmTooth width: 12 mmModule: m=1,5Content:1 piece

€17.50*

Average rating of 0 out of 5 stars

7429 FG Plastic gearwheel 41 teeth - 1pce.
Suitable for all 1:5 models. With 63 mm diameter.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

€18.90*

Average rating of 0 out of 5 stars

6422/01 FG Plastic gearwheel 44 teeth 2-speed - 1pce.
44 teeth plastic main gear for the layshaft with 2-speed gear.Diameter 69 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€17.90*

Average rating of 0 out of 5 stars

y6427/01 FG Plastic gear wheel 46 teeth 2-speed
46 teeth gear wheel for the layshaft with 2-speed gear box.Dampening rubbers with the order number 6051 are not required for this version.Dimensions:Diameter: 72 mmWidth: 15.5 mmTooth width: 12 mmModule: m=1,5Contents:1 piece

€14.90*

Customers also viewed

Average rating of 0 out of 5 stars

7427 FG Plastic gearwheel 40 teeth
Genuine FG spare/option part.Suitable for all 1:5 models.Dimensions:Diameter 63 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5Contents:1 piece

€18.90*

Average rating of 0 out of 5 stars

9468 FG Airbox 2011 without choke, set
Item N° 9468 Airbox 2011 without choke, setLight and very solid air box, high air permeability for more engine power. Without choke.Suitable for all Zenoah engines in 1:5 touring cars and 1:6 race trucks. DMC legal ( No. DMC 5 - 093 ).The set includes: Air filter adapter, air box, foam filter, gaskets and installation hardware.

€86.90*

Average rating of 0 out of 5 stars

7052 FG Plastic gear wheel 42 teeth - 1pce.
Gearwheel with 42 teeth for the layshaft. Diameter 66 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€17.50*

Average rating of 0 out of 5 stars

7432 FG Steel gearwheel hardened 24 teeth - 1pce.
Item N° 7432 Steel gearwheel hardened 24 teeth - 1pce.Suitable for 39, 40 and 41 teeth main gear wheel.Diameter 38.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5

€30.50*

Average rating of 0 out of 5 stars

LOSB3225 Losi F/R Wheel Hex & Pin 5T, TLR 5ive-B and Mini
Genuine Losi spare/option part.Fits Losi 5ive-T, TLR 5ive-B and 5ive Mini.Dimensionally identical with B55015Content:2 pieces

€39.99*
%

Average rating of 0 out of 5 stars

y1048 HT Aluminum-Frontaxle for FG Sportsline
Genuine FG spare/option part. Suitable for FG Sportsline (old version, not 4wheel drive basic) and Eco-Line.The set includes:Item N°.Name:y1027HT Aluminum a-arm 2WD, front uppery1026HT Aluminum a-arm 2WD, front lower, one-piecey1209HT Aluminum front bulkhead A y1210HT Aluminum front bulkhead B y1036HT rose joints with conical spacersUnit prices: 318,30 EURPlease note: the hinge pins are not included, you will use the pins from the stock suspension!Additional parts shown on the pictures, like diskbrakes or other tuning parts, are only decoration and not part of the set. Contents:1 set

€269.00* €318.30* (15.49% saved)

Average rating of 0 out of 5 stars

6103/05 FG Alloy upright front 1:6 2WD
Genuine FG spare/option part. Suitable for all FG 2WD Off-Road models. Not suitable for Monster-Truck models.Bearing seats 22x7 mm.Contents:1 set

€69.99*
Loading...
Upload in progress, please be patient ...
Shopware-Plugin Development Shopware-Agency