7439/05 FG Alloy gear carrier 52mm special, 1 pce.
€41.99
Available
Product information "7439/05 FG Alloy gear carrier 52mm special, 1 pce."
Alloy gear carrier 52mm special, 1 pce.
Precision alloy gear carrier, exact support of the plastic gearwheels 39, 40, 41, 42 and 44 teeth. Very low height design. For 10 mm diameter shafts.
Please note: competition layshaft 6041/05 is necessary for installation!
Lebacher Strasse 4
66113 Saarbrücken
Germany
Login
Alternatives
Fits FG and Smartech touring cars. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions. The following measures are required for installation of the HT-steel gear adapter "on-road" on the layshaft in FG EVO 2020 cars:- The installed wide 16T layshaft pinion 6431/01 must be replaced by the narrow version 6431.- The supplied 1mm shim must be added between layshaft pinion and ball bearing.- The flat sections on the layshaft do not have the usual 180° offset for the adapter; therefore only one grub screw will be used. However, since this is a wide face M8 version, this is no disadvantage.
Item N° 7439 Alloy gear carrier 52mm - 1pce.For 44T - 39T spur gears.For 10 mm diameter shafts.
Accessories / Spare parts
Fits FG and Smartech touring cars. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions. The following measures are required for installation of the HT-steel gear adapter "on-road" on the layshaft in FG EVO 2020 cars:- The installed wide 16T layshaft pinion 6431/01 must be replaced by the narrow version 6431.- The supplied 1mm shim must be added between layshaft pinion and ball bearing.- The flat sections on the layshaft do not have the usual 180° offset for the adapter; therefore only one grub screw will be used. However, since this is a wide face M8 version, this is no disadvantage.
Genuine FG spare/option part. Competition gear shaft, hardened and ground.Suitable for all FG models except Formel 1 and FG 4WD.Dimensions:Length: 103 mmDiameter: 10 mmContents:1 piece
Customers also bought
Item N° 6433 Steel pinion 20 teeth - 1pce.For combination with 44T main spur gear.Diameter 32.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5
Item N° 6432/02 Steel pinion 19 teeth - 1pce.For combination with 44T main spur gear.Diameter 32.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.
44 teeth plastic main gear for the layshaft.Diameter 69 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5
Genuine FG spare/option part. Rubber pucks for all standard design FG spur gear carriers.Dimensions:Outside diameter: 16 mmInner diameter: 7 mmHeight: 6 mmContents:4 pieces
Genuine FG spare/option part. Competition gear shaft, hardened and ground.Suitable for all FG models except Formel 1 and FG 4WD.Dimensions:Length: 103 mmDiameter: 10 mmContents:1 piece
Suitable for all 1:5 models.Diameter 63 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.
Customers also viewed
Genuine FG spare/option part. Competition gear shaft, hardened and ground.Suitable for all FG models except Formel 1 and FG 4WD.Dimensions:Length: 103 mmDiameter: 10 mmContents:1 piece
Item N° 7439 Alloy gear carrier 52mm - 1pce.For 44T - 39T spur gears.For 10 mm diameter shafts.
Item N° 7432 Steel gearwheel hardened 24 teeth - 1pce.Suitable for 39, 40 and 41 teeth main gear wheel.Diameter 38.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5
Genuine FG spare/option part. For 48T - 46T spur gears.Contents:1 piece
The factory-mounted combination of 980KV motor and 160A MAX6 esc provides performance that is second to none. With a 6S 22.2V (4S 14.8V is also possible) LiPo batteries, the motor reaches a final speed of about 25,000 rpm, leaving a comparable combustion engine far behind. The braking is done by the 980KV motor and is very strong. Within a few meters the model comes from top speed to a standstill. Those who have searched in vain for reverse gear with a combustion engine will find it with the electric version. The operation is very easy, if you press the brake lever once, you hit the brakes. If you press the brake lever twice, you shift into reverse. With the help of a programming card (available separately) you can adjust all ESC values according to your needs. This includes setting options for power, brake force, low-voltage protection and much more. Furthermore, the model has the following technical:The FG Sportsline Formula 1 electric convinces not only by its appearance, but rather by its technical achievements. The unique details such as push rods, horizontal oil pressure shock absorbers, double wishbone and much more can be found in almost no other model.The chassis is built on a high-strength 5mm aluminum chassis plate and thus offers extreme stability. Countersunk holes in the chassis plate allow the screws to be flush, ensuring a flat surface under the model. Versatile adjustment options on the front and rear axles allow the model to be perfectly adapted to your own needs. Adjustments such as camber, caster, etc. are no problem whatsoever, even for beginners, and are made via the double a-arms, which provide maximum stability at the rear axle by means of additional track rods. Also the adjustable aluminum oil filled shock absorbers convince on full length and offer maximum performance even on a very difficult underground. The above mentioned push-rod suspension enables play-free power transfer from the suspension to the shock absorbers, which is essential for precise driving. Features: 160A MAX6 esc, 6S compatible (4S also possible) 980KV brushless motor Waterproof components Adjustable aluminum oil filled shock absorbers Aluminum levers for the shocks Aerodynamic Lexan body shell 5mm thick aluminum chassis plate Mounting compartment for steering servo Mounting compartment for separate brake servo (for mechanical/hydraulic brakes) Cogged belt drive Side battery mounts for optimal weight distribution Custom CNC machined motor mount Unique double a-arms Push rod suspension Treaded F1 tires Tuning ball drive shafts Dimensions: Length: 960 mm BrWidtheite: 440 mm Height: 230 mm Wheelbase: 620 mm Technical data 980KV brushless motor: Max. Voltage: 33V Max. Current: 130A Max. Speed: 30.000RPM Power in watts: 4250W Rotor poles: 4 No-load current: 2.8A Resistance: 0.0128 Length: 82mm Diameter: 55 / 58mm with fins Weight: 880g Shaft diameter: 8mm Free shaft length: 30mm Weight: 880g Technical data Max6 esc: Continuous current: 160A Peak current: 1050A Battery: 3S - 8S LiPo or 9-24 cells NiMH BEC: 6V/7,2V - 3A/6A Abmessungen:70x56x46,5mm Weight: 240g Note: In our online shop you can also find a detailed 360° illustration, where especially the technology of the FG Formula1 electric chassis can be seen.Note battery mounting:When mounting the l/h side LiPo battery, you must always make sure that it does not rub against the drive pulley. For this purpose, a 5 mm thick piece of foam mat or something similar between battery and battery holder is sufficient to ensure an appropriate distance. For driving you still need: 2 drive batteries incl. charger Battery dimensions maximum: Length 143 mm/5,6 Width 48 mm/1,9 Height 40 mm/1,6 Connector EC8 The RTR equipment (remote control and steering servo!) The body shell comes unpainted! In our online store you can use our store configurator (shopping cart selection / options menu) to add the desired parts, as well as the completely painted body. Formular 1 models in action!