7573/01 FG Receiver 2,4 GHz for FG-RS3
Product number:
fg_7573_01
EAN:
3410569732194
Product information "7573/01 FG Receiver 2,4 GHz for FG-RS3"
Genuine FG spare/option part.
Contents:
Contents:
- 1 piece
Login
Customers also bought
%
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece
This model is fitted with numerous aluminium parts: front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Just like all other FG Competition models the FG Formula 1 Competition is the most successful model of the past years. The experiences we gained from numerous competitions have all influenced this version. The FG gearwheel drive which is extremely smooth running and cares for more power reserves. Surely FG Modellsport has created a competitive model for the next years with this version which will seamlessly follow up on the past successes. Highlights Alloy wishbones FG gearwheel drive Alloy rear axle plate FG alloy shock absorbers 04 Ball-bearing alloy servo saver 26 ccm Zenoah-Engine Airbox Tuned pipe Front- and rear brake 5 mm Chassis Lexan body shell Technical description of the FG Formula 1 Competition ki:The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with tuning bowden cable brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition kitCNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, mechanical Tuning brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.We deliver the models as a kit including mounting instruction. The body parts are made of clear polycarbonate for your own painting. FG stickers and writings are enclosed.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos (each approx. 40 - 50 kg), 2 servo for throttle brake (approx. 20 - 30 kg), batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engine Clear bodyshell and polycarbonate spoiler Mechanical brakesDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!
Hobbythek car bag for 1/5 carsFits for all 1/5 models for example: FG-: HPI-; Mecatech FW01-; Carson-; Smartech-; Conrads-; Harm-; RS5-; Lauterbacher a.s.oMade from extremely durable fabric, easily washable; with wrap-around shoulder belts and zipper closure.No dirt in the car boot!Dimensions:Length: 95 cmWidth: 40 cmHeight: 30 cm
Genuine FG spare/option part. Wheel / trigger type transmitter with ergonomic designRubber coated non-slip wheelLarge LCD display for easy settings10 model memoriesFHSS ModulationFailsafeDual rate on channels 1, 2 and 3Trims on the 3 channelsLow voltage (9,5V)7573/01 FG receiver 2,4 GHz fpr FG-RS3Contents:1 piece
Small steel modul (1,25) transmission set for Sportsline and Challenge Line, improves performance and reliability.
Similar products
Genuine FG spare/option part. Wheel / trigger type transmitter with ergonomic designRubber coated non-slip wheelLarge LCD display for easy settings10 model memoriesFHSS ModulationFailsafeDual rate on channels 1, 2 and 3Trims on the 3 channelsLow voltage (9,5V)7573/01 FG receiver 2,4 GHz fpr FG-RS3Contents:1 piece
Customers also viewed
Genuine FG spare/option part. Wheel / trigger type transmitter with ergonomic designRubber coated non-slip wheelLarge LCD display for easy settings10 model memoriesFHSS ModulationFailsafeDual rate on channels 1, 2 and 3Trims on the 3 channelsLow voltage (9,5V)7573/01 FG receiver 2,4 GHz fpr FG-RS3Contents:1 piece
%
Complete RTR 2x TT1530/250 TT 5000 mAh LiPo Batteries 2S, 7,4V 60C y1580 HT T240 Duo AC/DC, 2 x 120W, bis 6S, Charger 2x TT1499 Top Tuning Safety Bag für LiPo Batteries Genuine FG spare/option part.The electric powered version of the legendary Marder buggy is equipped with a powerful 1400kV brushless motor. Power supply: 4S or 4S Li-Po battery pack. In its entry level version 4S, the running time is about 15 minutes with lightning-accelerations and a top speed superior to the gas powered Marder one. In the 4S configuration, the E-Marder is a true rocket ship!In the first place our 1:6 Off-Road Buggy stands for driving fun. Through the knobbed tires or with Slick tires (optional extras) the model can be driven cross-country, on a car park, simply just everywhere.The RTR version of the car includes servo, transmitter, receiver, transmitter / receiver and rechargeable batteries. 2WD Off Road BuggyMachined 4 mm aluminum chassis plate with side guardsIndependent suspension with many options for adjustmentRoll cage, can be used as a carrying handle as wellClosed factory painted body shell with decals already appliedFlange rims with knobby tires1400 kV motor150A brushless ESCTwo locations for the batteries with hook-and-loop strapsDimensions:Length: 620 mmWidth: 420 mmHeight: 260 mmWheelbase: 470 mmWeight: 6,4 kgContents:1 piece
Genuine FG spare/option part. The differential key prevents a damage of the diff. cover through bigger stones. Suitable for all FG 1:6 Buggy and Monster models.Contents:1 piece
Genuine FG spare/option part. The FG Marder body shell is delivered white and without window gitter or decal set.Dimensions:Length: 580 mmWidth: 240 mmHeight: 205 mmContents:1 piece
After the successful introduction of the 4WD Sportsline chassis for 1:5 FG Touring and Sports cars this chassis is now available also for Race Trucks. Mainly rookies benefit from the advantages of an all-wheel drive. Traction also on dusty asphalt, therefore no pulling of the rear section, all around just pure driving fun. These are just some advantages of the four-wheel drive.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The body shell is clear.The Race Truck chassis is equipped with a double wishbone suspension, toe-in, camber and castor can be adjusted. The robust all-wheel drive gives the vehicle a neutral driving performance on almost every surface. We set big value on durability using strong materials as well as operator convenience. The FG Sportsline class is the affordable, but still high-quality entry into the RC car sport.Technical description:Equipped with a powerful 26 cm³ engine, Tuning pipe, tank with snap closure, 2 differential gears, front disk brake and a lot more. Highlight however remains the approved FG all-wheel drive. Maximal traction as well as simple handling, grip in curves - these are the advantages only a four-wheel drive can offer. With a wheelbase from 530 mm.Dimensions:Length: 880 mmWidth: 435 mmHeight: 380 mmWheelbase: 530 mm Trucks in action!
Gearwheel protection in transpartent polycarbonate for all FG 1:5 scale models with the gear wheels 38, 40, 42 teeth. Protects the driving gear wheels almost from dirt, sand and stones. We recommend the mounting when driving on car parks. Not suitable for Formel 1, Leopard 2 + 4 Competition, Competition and Competition Evolution models.