25 products found for "y1107"
rc-car-online - Home
Genuine HT spare/option part. Two balljoints 5mm/M8 with four conical spacers, to replace FG #6029/1 + balls (Set content like FG 4429/1).Fits almost for all 1/5 and 1/6 scale cars.The maintenance-free rod ends with the sliding contact surface combination steel/ bronze composite feature a spherical plain bearing with a brass outer ring which is lined with a layer of bronze web in to which PTFE with molybdenum disulphide has been rolled. Contents:2 pieces
Genuine HT spare/option part. Maintenance tray for all 1/5 scale RC car models. The tray with its rubber pad prevents the car from sliding while working on the vehicle at the race or in the basement.Dimensions:Length: 370 mmHeight: 60 mmWidth: 170 mmContents:1 piece
Genuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piece
Genuine HT spare/option part. Powerfull high quality soldering torch with piezo igniter, runs on standard lighter gas. Great for removing bolts that have been installed using thread locking compound. Removable safety base for convenient hands-free operation., adjustable flameTechnical data:Flame temperature: approx. 1.300 °COperating temperature: approx. 650 °CTank capacity: approx. 26 g ButaneConsumption: approx. 20 g/hFlame adjustement: from 12 mm to 32 mmIgnition system: piezo ignition (like electronic lighters)Please note: due to shipment regulations the torch is not filled with gas when delivered!Contents:1 piece
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Genuine HT spare/option part.Version V2 with new design and quieter fans.Designed by professionals, this system is extremely versatile. The HT206AC / DC Duo 2 is very easy to use with the vertically angled 4.3" color touch display. The colorful app icons allow quick and clear navigation through the menu. The charger is cooled by a total of three powerful fans, which prevent overheating even at high outside temperatures. The heat dissipation is also increased by the aluminum housing.It is possible to charge two different batteries simultaneously with different charging settings. The HT206AC / DC Duo 2 provides a total of 400 watts, 200 watts per channel. Thus, each battery can be charged or discharged individually. The battery life can be increased with the balancing function.Specifications: AC input voltage: 110 - 240VDC input voltage: 10 - 30VDC output power: 5 - 27V, 0.1 - 20ACharging Power: 2 x 200W (400W) Charge Current Range: 0.1 - 20 A x 2Discharge current range: 0.1 - 5 A x 2 Max Discharge power: 25W x2 (50W) balancer current: 500mA / cellLilon / LiPo / LiFe / LiHV cell count: 1 - 6 cellsNiCd / NiMH battery cell count: 1 - 15 cellsPb Battery voltage: 2 - 20VMax. USB output: 5V / 2ABattery Memory: 8 profilesSub-function: digital power, balancer, IR testFirmware upgrade: External mini USB deviceSize: 195 x 143 x 70 mmWeight: 1072g Content: b> 1 x HTRC HT206AC / DC DUO charger 2 x T60 on banana connector adapter 2 x Balancing Board1 x Mains cable li> 1 x Instruction manual
Complete tuned pipe system, will be delivered as shown with manifold, hose with clamps and variable mount. Fits FG and Carson touring cars / GTs with long wheel base.The tuned pipe is for a 535 wheelbase. The diameter is 51 mm and the complete length is about 300 mm.
Exhaust port and carburetor intake cover plates, made of 1 mm aluminum, fits most current 23cc - 30cc rc-car engines.Exhaust port cover:Total: approx. 20 x 45 mmMounting holes (ctr./ctr.): approx. 34 mm carb intake cover:Total: ellipse approx. 28 x 40 mmMounting holes (ctr./ctr.): approx. 31 mm
These cask shaped springs are especially designed to fit the diameters of Mecatech Klick-Shocks and Mecatech Big Bore shocks.Set with one pair each of blue, red and yellow springs.Dimensions:Inner diameter, upper: 20,5 mmInner diameter, lower: 16,5 mmOutside diameter: 29,5 mmLength: 49,5 - 52,5 mm
y1103 Size:
y1103/01 - Small
Genuine HT spare/option part. You can select from two different sizes of body support.Dimensions small body support y1103/01:Length: approx. 80 mmWidth: approx. 16 mmDistance bore to bore: approx. 64 mmDimensions large body support y1103/02:Length: approx. 105 mmWidth: approx. 16 mmDistance bore to bore: approx. 88 mmBore diameter: approx. 8 mmContents:2 pieces
Genuine HT spare/option part.Two balljoints 5mm/M8 left-hand threadThe maintenance-free rod ends with the sliding contact surface combination steel/ bronze composite feature a spherical plain bearing with a brass outer ring which is lined with a layer of bronze web in to which PTFE with molybdenum disulphide has been rolled. Dimensions:A = 5 mmB = M8 rightC = 8 mmD = 17,5 mmE = 39 mmContents:2 piece
y1101 Application:
y1101/05 Ace DS1015 Super Torque Digital Servo
Item N° y1101 Servo horn mounting screws, 10 pcsReplacement screws for mounting the servo horn on the servo shaft.Part is delivered in silver or black color from vendor!Choises:y1101/01Fit:Multiplex Jumbo and Power MCFG 6598 Savöx-Servo SC-0251MGFG 6599 Savöx-Servo SC-1256TG Measures: M3 x 8 mmy1101/02Fit:Multiplex RhinoHitec 805 MGHitec 9805 MGFutaba S3152 Measures: M2,5 x 10 mm Torxy1101/03Fit:Futaba und Robbe diverse ServosPlease check the required dimensions! Measures: M2,5 x 6 mm Torxy1101/04Fit:402115 Mega Power-Servo, metal gears Measures: M3 x 10 mm y1101/05Fit:Ace DS1015 Super Torque Digital Servo, y1051 Measures: M3 x 10 mm
Genuine FG spare/option partfor FG Evo 2020 models.Content:1 piece
y1207 Content of delivery:
Set with l/h andr/h version+ 30EUR
Genuine HT spare/option part.Very strong one-piece a-arm for use with rose joints. Features Igus bushings for the hinge pins (stock hinge pins can be re-used). Rose joint and conical spacers included!Fits Smartech Monster-Truck, UNO, Carson Comanche, Attack Evo, CRT and CPT. Contents:1 piece
Variants from €59.90*
Walbro Vergaser WT1107 with choke Standard carburetor for Zenoah G320. Typ: Walbro WT1107This is the stock carburetor used for the G320RC engine, and will also work on all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23 cm³ up to over 30 cm³. Dimensions:Bore: 15,88 mmVenturi: 13,5 mmIndependent tunable high and low speed jets.The carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23 cm³ up to over 30 cm³.
Offerset:2 Pairs MadMax Maxi Pin tires2 Pairs MadMax rims2 Pairs MadMax inlays2 Pairs / 4 pieces adapter TT1020/01MAXI PIN 185 x 75 with black colored MadMax Extreme rims, 20-fold screwed, very tough, with 24 mm hex drive and with reinforced orange beadlock rings for Losi and HPI. The MadMax MAXI PIN tires come with strong special tire inserts which allow transferring the power without canting, even on heavy cars. MadMax MAXI PIN tire was developed specifically for astro turf tracks! The special tread design with 480 studs per tire provides excellent grip, but also a high load on tire and rim! To stabilize the tire, the outer shoulder features radial ribs which minimizes the tilting under load and counteract the shear forces during cornering. Furthermore, the MAXI PIN tire has studs positioned on the outside shoulder, which support the steering in corners. All together the MAXI PIN tires provide maximum grip, which made it necessary to upgrade the beadlock screws on these MadMax EXTREME wheels. So they come with 3.0 mm screws instead of the usual 2.5 mm ones! Nevertheless, tires and beadlocks should be checked after every run.The set consists of four tires, including tire inserts and MadMax EXTREME rims and 4 pieces adapter wheel nuts TT1020/01. Dimensions: Outer diameter: 185 mm tire width at bead: 70 mm Tread width: 75 mm Reinforced 24 mm hex wheel drive The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!TT1020 Top Tuning Adapter wheel nutGenuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces
Genuine HT spare/option part. Foldable maintenance tray, ideal for 1/5 and 1/6 cars; even for heavy weight and high ground clearence cars like a Losi 5ive-T!Size folded:Width: 300 mmHeight: 315 mmDepth: 40 mmWeight 1 kgSize erected: Width: 300 mmHeight: 220 mmDepth: 210 mmContents:1 piece
Genuine Zenoah spare/option part. Replacement part fits Zenoah G320RC.
Genuine Losi spare/option part. Contents:1 set
With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.With the new "K & N" version of the Losi DBXL there is another detail, which need to be considered.From the very beginning the hole pattern for the engine installation in the DBXL chassis plate was no precise match to the hole pattern of the engine, even when delivered in stock form with standard engine. Now with the "K&N" version the engine mount has been changed to eliminate this discrepancy. However, all aluminum engine mounts available on the market share their dimensions with the previous plastic engine mount. For the installation of a G320 Zenoah in a "K&N" -DBXL two possible combinations exist in order to obtain the correct hole pattern:When using the standard (new) plastic engine mount a shortened clutch housing is required as in a 5ive-TWhen using an aluminum engine mount a stock length clutch housing is requiredSeparately, it is recommended to enlarge the cutout in the body panel in front of the K & N air filter for about 2 - 3 mm to ensure that the panel cannot chafe on the air filter.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.
y110010 Thickness:
y11001050 - 0,5 mm
Top quality gasket Available in the following versions: y11001030 - 0,3 mm y11001040 - 0,4 mm y11001050 - 0,5 mm Contents:1 piece
Set consists of 4 dampers. Premium version, suitable for FG, Carson / Smartech etc.
Fully assembled and filled. Special features: 16 mm inner diameter for higher oil volume Volume equalisation Housing and screw connections made entirely of aluminium Hard anodised housing Precision piston made of Delrin, machined (no moulded part!) Aluminium piston rod base and aluminium spring plate Replaceable bearing bushes in the mounting eyes Pre-filled with 1000 silicone oil. For the following models: FG 4WD:
Monster Truck, Monster Jeep, Monster Hummer, Stadium Truck, Stadium Jeep, Stadium Hummer, Off-Road Beetle Set contents:
Four long dampers with 5 mm mount in the upper damper caps. Damper feet one pair short, one pair long (4WD MT version). We recommend our progressive off-road tuning shock absorber springs from the "Dirt-Spring M" series, part number y0321, for the shock absorbers. The original springs can also be used on FG models! Silicone oil recommendation: The GPM-Spezial Cross shock absorbers are filled with silicone oil viscosity 1000. This viscosity provides very good damping properties at normal outside temperatures. If softer damping is required, oil with a viscosity of 500 or 600 is recommended; for harder damping, 1500 or higher is recommended. One 50 ml bottle of y0038 is sufficient for five long or six short dampers.
Product information "y1137/02 GPM-Big Bore Premium shock absorbers for FG Monster/Stadium Truck 2WD, set" Set consists of 4 shock absorbers. Premium version, suitable for FG, Carson / Smartech etc. Fully assembled and filled. Special features: 16 mm inner diameter for higher oil volume
Volume equalisation
Housing and screw connections made entirely of aluminium Hard anodised housing
Precision piston made of Delrin, machined (no moulded part!)
Aluminium piston rod base and aluminium spring plate Replaceable bearing bushes in the mounting eyes
Pre-filled with 1000 silicone oil. For the following models:
FG 2WD:
Monster Truck, Monster Jeep, Monster Hummer, Monster Beetle Pro, Stadium Truck, Stadium Jeep, Stadium Hummer
Set contents: Four long shock absorbers We recommend our progressive off-road tuning shock absorber springs from the "Dirt-Spring M" series, part number y0321, for the shock absorbers. The original springs can also be used on FG models! Silicone oil recommendation: The GPM-Spezial Cross shock absorbers are filled with silicone oil viscosity 1000. This viscosity provides very good damping properties at normal outside temperatures. If softer damping is required, oil with a viscosity of 500 or 600 is recommended; for harder damping, 1500 or higher is recommended. One 50 ml bottle of y0038 is sufficient for five long or six short dampers.