y1107 Steel balljoints 5mm/M8, with conical spacers

€14.90*

Available

Product number: y1107

EAN: 4058575023197

Product information "y1107 Steel balljoints 5mm/M8, with conical spacers"

Genuine HT spare/option part.

Two balljoints 5mm/M8 with four conical spacers, to replace FG #6029/1 + balls (Set content like FG 4429/1).

Fits almost for all 1/5 and 1/6 scale cars.


The maintenance-free rod ends with the sliding contact surface combination steel/ bronze composite feature a spherical plain bearing with a brass outer ring which is lined with a layer of bronze web in to which PTFE with molybdenum disulphide has been rolled.

Contents:

2 pieces

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

y0529 Steel ball joint 6 mm r/h or l/h thread, 4 mm bore in ball

y0529 Version: y0529L One piece left hand thread+ 1EUR

Steel ball joint 6 mm r/h or l/h thread, 4 mm bore in ball, for steering rods and other applications.This version is for steering rod applications.Sets available:One each with r/h and l/h threadOne x r/h threadOne x l/h thread Please note:We recommend using a nut 4472/03 for locking the r/h thread ball joint to prevent the linkage from loss of adjustment.

Variants from €5.90*

€6.90*

y0529/01RL Steel ball joint 4 mm r/h or l/h thread, 3 mm bore in ball

Steel ball joint 4 mm thread, 3 mm bore in ball, for servo saver/servo linkage.This version is for servo linkage.Sets available:One each with r/h and l/h thread

€10.80*

y1106/01 Aluminum ball joints with 5mm/M8 right-hand thread, 2 pieces

Genuine HT spare/option part. Two balljoints 5mm/M8 right-hand threadThe maintenance-free rod ends with the sliding contact surface combination steel/ bronze composite feature a spherical plain bearing with a brass outer ring which is lined with a layer of bronze web in to which PTFE with molybdenum disulphide has been rolled. Dimensions:A = 5 mmB = M8 rightC = 8 mmD = 17,5 mmE = 39 mmContents:2 piece

€14.90*

Configure now

y0529/02R Steel ball joint M8 r/h or l/h thread, 5 mm bore in ball

One pieces of steel ball joint with 5 mm bore in ball and M8 r/h or l/h thread.Suitable for most every 1/5 and 1/6 car!Replaces FG plastic ball joints # 6029/08 and # 6081/01 in conjunction with the conical spacers # 4429/02.Replaces Smartech # 32409 and # 32446 as well.

€5.90*

y0529/01R Steel ball joint 4 mm r/h or l/h thread, 3 mm bore in ball

Steel ball joint 4 mm r/h, 3 mm bore in ball, for servo saver/servo linkage.This version is for servo linkage.Sets available:One x r/h thread

€5.90*

4429/02 FG Steel taper disk 5mm bore

Genuine FG spare/option part.Steel taper disks, 3.5 mm thick, with a higher stiffness compared to alloy taper disks. Installation of these disks allows for larger operation angles of the metal ball joints and rose joints. You need two disks per joint.Contents:4 pieces

€9.90*

6027 FG Ball-and-socket joint 6mm with ball

Genuine FG spare/option part. Plastic ball joint Fits all FG cars.Dimensions:Thread size: M4Länge: 20 mmBall bore: 3 mmHeight: 8 mmContents:6 pieces

€15.50*

y0529/02L Steel ball joint M8 r/h or l/h thread, 5 mm bore in ball

€5.90*

4429/01 FG Steel balljoint Ø5/M8

Genuine FG spare/option part.Steel ball-and-socket joint with 5mm bore in the ball and M8 right-hand thread for installation on the wishbones.Delivery contains all needed pin disks.Dimensions:A = 5 mmB = M8C = 8 mmD = 16 mmE = 37.5 mmContent:2 pieces

€54.50*

6027/05 FG Ball-and-socket joint 6mm for M2 screw thread

Genuine FG spare/option part. Length: 20 mm.Contents:5 piece

€5.90*

y0882 Metal ball joints set

y0882 Version: y0882/01 Steel version

Aluminum or steel balljoints for replacement of the stock plastic units on the a-arms of all FG cars except Formula 1. Alloy:A = 5 mmB = M8C = 8 mmD = 17,5 mmE = 39 mmSteel:A = 5 mmB = M8C = 8 mmD = 16 mmE = 37,5 mmContent:8 x Aluminum or Steel balljoints, M8 r/h thread, 5mm bore diameter in the ball8 x low height nut, M8 r/h thread 16 x conical alloy spacer

€49.90*

y1106/02 Aluminum ball joints with 5mm/M8 left-hand thread, 2 pieces

Genuine HT spare/option part.Two balljoints 5mm/M8 left-hand threadThe maintenance-free rod ends with the sliding contact surface combination steel/ bronze composite feature a spherical plain bearing with a brass outer ring which is lined with a layer of bronze web in to which PTFE with molybdenum disulphide has been rolled. Dimensions:A = 5 mmB = M8 rightC = 8 mmD = 17,5 mmE = 39 mmContents:2 piece

€14.90*

Customers also viewed

6038 FG Engine mount washers for M4 and M4 screws

Genuine FG spare/option part. Washers for the screws (M4 / M5) that hold the engine mounts to the chassis. Suitable for all FG models.Dimensions:Outside diameter: 15 mmInside diameter: 6 mmContents:4 pieces

€6.50*

y0529/02R Steel ball joint M8 r/h or l/h thread, 5 mm bore in ball

€5.90*

6049/01 FG Clutch bell

Genuine FG spare/option part. New version clutch bell for all FG cars except Formula 1. Contrary to the previous version 6049 the flat areas for the pinion set screws are angled at 90° instead of 180° (see pic).Dimensions:Shaft diameter 10 mmShaft length 38,2 mmOverall length 61 mmAouter diameter bell 58 mmInner diameter bell 56 mmContent:1 pieces

€53.95*

HT Aluminum rear suspension conversion kit for Smartech UNO, Carson Attack / Super Attack / Gas Blaster / C5 / R5, 2WD , y1003, set

Alloy rear axle conversion kit for Smartech UNO and Carson Attack and Super Attack (not Evo!), Gas Blaster and C5; Smartech Spider and Ranger cars.Fits for:- C5 / On road / Touring car- C6 Attack- Touareg- Super Attack- Gas Blaster- Duratrax Firehammer- Spider- Big AttackThe set includes:- rear plate- differential mounts- lower a-arms- upper a-arms- installation hardware.Please note: must use inge pins 6075, also you need two packets turnbuckle 40 mm 6100/04.

€299.90*

Gas-nitrited tuning clutch bell for all cars to choose

For Model: y0726/01 Gas-nitrited tuning clutch bell for Losi DBXL

Different versions to choose:y0723 Gas-nitrited tuning clutch bell for FG, Smartech / Carson, Harm, RS5 & Co..Gas-nitrited tuning clutch bell; machined from high grade steel with vents for cooling of the clutch system and holes for easy clutch adjustment. The clutch bell features a significantly reinforced wearing surface which guarantees dimensional stability even under high loads!For best mounting of the pinion the clutch bell shaft has to flats with a 90° offset. As an additional safety device a M5 bolt with washer (included) replaces the E-clip found on stock clutch bells.Suitable for many 1/5 and 1/6 cars, such as all FG (except Formula 1), Carson a.s.o.y0726 Gas-nitrited tuning clutch bell for Losi 5ive-T (unfortunately not available at the moment Alternatively original Losi clutch bell # LOSB5038) ) Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface and face which guarantees dimensional stability even under high loads! The shaft is a tiny bit longer than stock (about 0.2 mm) to prevent the bearings from binding.Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Scale-Cross clutch.Suitable for genuine slot drive Losi pinions. Comes with bolts and spring washers included.y0726/01 Gas-nitrited tuning clutch bell for Losi DBXLGas-nitrited tuning clutch bell with black oxide coating, machined from high grade. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well. This clutch bell is dimensionally identical to the stock part. Heat treatment and the use of a high grade material guarantee long service life.Due to a special heat treatment the clutch bell surface is shaded; this does not effect the function, but ensures great durability.y0729 Gas-nitrited tuning clutch bell for HPI Baja models, 1 pce.Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface whichguarantees dimensional stability even under high loads!Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Scale-Cross clutch.Suitable for slot drive HPI Baja pinions, both stock using a 4mm bolt and aftermarket ones for 5mm bolts. Comes with M4 and M5 bolts included.

€49.90*

2012-94 Mecatech Clutch Flange Spacer

Genuine Mecatech spare/option part for the FW01.Content:1 piece

€7.50*

Details