y1007 CFH Diamant M50 gas torch

Item N° 50353011Support Blocks for the Lightscale Droop Gauge front, 1 pce.This is an Alloy Support Block anodized in black colour with 30mm height.The Support Block is manufactured as a rectangle and so can used a 30mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.

Genuine Top Tuning spare/option part. Motor adapter plate to mount the ZTW 620KV Beast motor into the Losi DBXL-E 2.0. The plate has four mounting holes, which should also be used due to the enormous torque of the ZTW motor. In order to install the screw at the l/h top position, at least 0.6mm material must be removed from the existing motor/differential mount. Contents:1 piece

The perfect tool for drilling perfectly round holes without cracks into a body shell.The cap protects the extremely sharp and spiky tip, the convenient handle provides secure grip on the tool.Dimensions:For holes up to 14 mm diameterLength of tip: approx. 45 mmTotal length: approx. 132 mmContent:1 Piece

The new Raceline FF 530 is a very powerful competition model at an affordable price.In some countries a new competition category has been established so that as many RC car drivers as possible can enter the competition cheaply.RACELINE FF 2WD 530 Especially for competition use!The model is pre-assembled and the RC system, servos, front bumper and air filter still need to be fitted.  We also recommend checking all screws. Features:Front upper POM* a-armsfront/rear lower POM* a-armsPOM front axle bracketPOM shock mounts front and rear5 mm chassis platedual large diameter disk brakealuminum differentialNew rear braceDrive optimizationFront and rear aluminum spindles/uprightsAdjustable aluminum servo saverAluminum gear plateAluminum spur gear carrierLarge-volume tuned pipe systemHomologated and large volume airbox and tuned pipe systemOne advantage of POM* is its high dimensional stability. That means that it hardly changes its shape. The polymer has very good sliding and wear properties. The plastic has high strength and rigidity as well as medium to high impact strength and hardness. Its advantages also include high resilience. A very low center of gravity of the vehicle ensures good driving behavior on the track, the servos are installed lying down to support this behavior.*Polyoxymethylene (POM for short) are high molecular weight thermoplastics. The colorless, partially crystalline polymers are mainly used for the production of molded parts by injection molding.Content:1 piece

Incl. TT1030 Top Tuning CAR-STAND. worth €219.99 free of charge.Competition-OnRoad RC car with the latest technical developments.  Unique among the large scale models. New stabilizer bar construction front and rear. Ball stabiliszers or frame stabilizers can be used (accessories). 10 mm thick chassis made of T7075 aluminium with cut-outs for weights (also under the tank) and grooves in the front area. This allows the vehicle to be perfectly adapted to the track or the driver. The engine is now again bolted to the chassis for more stiffness. Optimally designed wishbones on front and rear suspension. Reinforced and with toe-in adjustability, which is performed via aluminum wedges. Front upper wishbone for more adjustment possibilities. All gears with fine pitch.Since 1997, i.e. since the beginning of the 1:5 RC car scene, FG Modellsport has been represented with team drivers worldwide at national and international competitions. With the Competition-EVO series, FG won most world championships and almost all European championships. Content Top suspension with 10 mm T7075 aluminum chassis plate Zenoah G230RC Engine Adjustable Tuning Clutch Air filter / Airbox Tuned pipe system Front and rear hydraulic brakes Differential Large volume shock absorbers, black anodized Wheels and rimsYou will also need: - 1:5 scale body with a 530/535 wheelbase - Complete radio control system (transmitter and receiver) - 2 throttle/brake servos and 1 steering servo - Receiver battery