Fully synthetic oil, available in three blends. 1-liter bottle.The optimal 2-stroke oil for 23-30 cm³ engines/cars Motul Racing Oil is available in three different blends: On-Road for high revving onroad cars Off-Road for cars with high torque enginesMixing ratio for 1/5 & 1/6 applications: We recommend a mix with about 4% oil, which means 200 cc of oil to 5 litres of gas (1:25 ratio). With one litre of Motul oil you can mix about 25 litres of optimal fuel for your 1/5 or 1/6 car. That's enough for well over 20 hours of driving fun! Oil / Gas Oil percent Oil per 1 liter of gasoline Oil per 2 liter of gasoline Oil per 3 liter of gasoline Oil per 4 liter of gasoline Oil per 5 liter of gasoline 1:20 5% 50 ml 100 ml 150 ml 200 ml 250 ml 1:25 4% 40 ml 80 ml 120 ml 160 ml 200 ml 1:30 3,33% 33 ml 67 ml 100 ml 134 ml 167 ml 1:33 3% 30 ml 60 ml 90 ml 120 ml 150 ml 1:35 2,86% 29 ml 58 ml 86 ml 115 ml 143 ml 1:40 2,5% 25 ml 50 ml 75 ml 100 ml 125 ml 1:50 2% 20 ml 40 ml 60 ml 80 ml 100 ml

Genuine HT spare/option part. After-Run is a performance enhancing preservation, which ensures that the engine starts properly, even after a long time (winter break) storage. Added to the fuel it keeps the fuel system clean.Among other After-Run conserves the diaphragm of the Walbro carburetor!For long term storage (i.e. during winter!) "vital" for the carburetor diaphragms!For 23 to 32 cm³ engines like Zenoah, Chung Yang, PT, Losi, HPI a.s.o.It binds water in the fuel, particularly important when the engine is not run regularly or after wet races. After-Run improves engine performance, ensures better combustion, removes debris and residues. Simply add the content of the bottle to 5 litres of fuel.Contents:1 piece / 20 ml

Item N° y19281 HT-tire adhesive 4000, 1pce.1 piece / 20 grammsHT-tire cement, specially formulated for rubber/plasticContent:20 gr bottle

Genuine Motul spare/option part. High-cling oil for foam cartridge air filters, especially for offroad and street use. The oil reinforces the the air filter'e efficiency and retains dirt, mud and sand particles, which will greatly extend the life of the engine. The blue tint makes it easier to control even oil application to the filter.Apply oil to filter generously and work the foam vigorously by hand to ensure complete oil penetration. Press foam slightly to remove excessive oil when done.Contents:1 piece / 400 ml

Genuine HT spare/option part.Available as 272 high strength and heat resistant, 270/1 high strength or 241 medium strength.The strength of 272 and 270/1 is comparable, but 272 can handle temperatures up to 230°C vs. 150°C for 270/1. It is therefore the perfect choice for applications like exhaust or clutch pinion bolts. However, curing of 272 takes at least twice as long as 270/1.An excellent recommendation for removal of screws treated with threadlocking compound:CFH Diamant M50 Gasbrenner, y1007 Contents:1 piece / 10 gram

This air filter oil is designed for lubricating foam filters for on-road and off-road use. It reinforces the filters' efficiency for better carburation and retains dirt, mud and sand particles. Prevents water from penetrating into the filter.It is recommended to put the filter with a little bit oil in a small polybag and work it vigorously by hand. Excessive oil must be pressed out (don't wring the foam!) afterwards.For cleaning the filter please use the special foam cleaner y0523.The filter element must be dry before re-oiling.Content:50 ml

Freaking expensive, but it is damned fine.ASONIC HQ 72-102 is a synthetic high-temperature lubricating grease, for use in limited slip differentials. Due to the careful selection of product components and the clean manufacturing environment, ASONIC HQ 72-102 is a rolling bearing grease with a particularly low noise level.Benefits for your application:High-temperature lubricating grease for rolling bearingsHigh purityLow noiseGood water resistanceContent:1 piece, tube with 30g

Genuine rc-car-online spare/option part. Foam-Cleaner, special cleaning agent for foam air filter elements and GPM coverThe foam-Cleaner is specially designed for RC foam air filters, as well as covers for starter, filter and shocks. Removes reliably dirt, mud, dust, old filter oil, and sand particles and ensures optimum air flow. After cleaning please oil the air filter with air filter oil with order-no. y0284 for foam filters before re-use. Routinely cleaning of filters protects against premature wear and extends engine life!Use: apply cleaner to filter/cover, wait for some minutes and rinse with warm water. Let the parts dry before re-use.Bottle with 500 ml.Contents:1 piece

Marston Universal blue is the leading non-setting gasket and sealing compound in use world-wide. The product is used by many of the world?s major automotive manufacturers and by several Formula 1 teams.Features- Non hardening and non setting- Unlimited assembly time- Vibration resistant- Allows metal to metal contact- Resistant to combustion products, water, engine coolant, petroleum, lubricating oils, kerosene and fluorocarbon refrigerants- Seals surface imperfections- Withstands rapid variations in temperature80 ml tube

Genuine HT spare/option part.Available as 272 high strength and heat resistant, 270/1 high strength or 241 medium strength.The strength of 272 and 270/1 is comparable, but 272 can handle temperatures up to 230°C vs. 150°C for 270/1. It is therefore the perfect choice for applications like exhaust or clutch pinion bolts. However, curing of 272 takes at least twice as long as 270/1.An excellent recommendation for removal of screws treated with threadlocking compound:CFH Diamant M50 Gasbrenner, y1007 Contents:1 piece / 10 gram

Special oil for plastics in precision applicator; following special advantages:- Friction reduced ten-fold- Completely smooth running- Wear reduced by 90%- Resistant to fuel attack and ageing- Does not attack plastic materials- Temperature range -30°C to 150°C Applications:- Bowden cables- Ball-links and joints- Plastic differentials- Transverse armcontent 4ml

For changing the locking effect of large scale car differentials.Top quality in 50 ml plastic wide-neck bottles.Silicone oil / grease with a viscosity to choose:15.00030.00050.000100.000300.0001.000.0002.000.000Viscosity of silicone oil at various temperatures.

Item N° 6512/01Differential grease 500.000, 50mlSemi-fluid differential grease for all differentials without barrier effect. Not suitable for adjustable, Powerlock and viscous differentials.

Genuine silicone shock absorber oil for the optimal shock absorber set-up. Content: 100 ml Please note: Factory filling of FG/Losi/Smartech and many other 1/5 and 1/6 scale shocks is done with genuine silicone shock absorber oil. To ensure seal tightness and consistency you should only use genuine silicone shock absorber oil for refilling as well.Most every rc-car shock absorber uses silicone oil of different viscosities. The smaller the number, the lower the viscosity of the silicone oil and the softer the damping. As a rule of thumb: Viscosity 100 = similar to water Viscosity 1.000 = similar to cooking oil Viscosity 5.000 = similar to shampoo Viscosity 10.000 = similar to honey As a reference: The red FG Marder / Off-Road Buggy series shock absorbers are factory filled with 2.000 viscosity oil, the shocks on monster cars with dual shock set-ups (total of 8 shocks) are filled with 1.000 viscosity oil, and the shocks on FG onroad cars come filled with 4.000 viscosity oil. The original filling of the Losi 5ive-T is 350cc silicone oil.FG Silicone oil with 100 ml:FG Item N° 66295/010 = Viscosity: 100 FG Item N° 66295/025 = Viscosity: 250FG Item N° 66295/035 = Viscosity: 350FG Item N° 66295/050 = Viscosity: 500FG Item N° 66295/075 = Viscosity: 750FG Item N° 66295/100 = Viscosity: 1000FG Item N° 66295/150 = Viscosity: 1500FG Item N° 66295/200 = Viscosity: 2000FG Item N° 66295/300 = Viscosity: 3000FG Item N° 66295/400 = Viscosity: 4000FG Item N° 66295/500 = Viscosity: 5000FG Item N° 66295/600 = Viscosity: 6000FG Item N° 66295/700 = Viscosity: 7000FG Item N° 66295/800 = Viscosity: 8000FG Item N° 66295/900 = Viscosity: 9000FG Item N° 66296 = Viscosity: 10000Viscosity of silicone oil at various temperatures.

Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!) Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!) The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended. For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.Attention:Clutch-Safe adhesive must be stored in the fridge! Content: 10g tube

Especially for installation of all engine gaskets. Temperature resistant from -55 °C to +200 °C. Resistant to water, mineral oils, synthetic lubricants, fuels, organic solvents and refrigerants. info: Hand tight: 10 - 20 minReady to use: 1 - 3 hoursGap fill: 0.5 mmContent: 50 ml Notes for usage: This surface seal is not for use as the sole sealant, it should always be applied in combination with a paper gasket.The HT-surface sealing agent should be sparsely applied over the entire surface, with care being taken that the sealant does not enter the devices internals (e.g. crankcase, differential a.s.o.) during the assembly.

Special plastic cleanerPE100 was specially developed to protect plastics from external agents. The product penetrates right into the molecular structure of the plastic,which is thus protected from the inside out, remains permanently supple and retains its natural gloss.Most RC cars have various axle parts, such as control arms and bearing blocks made of plastic. Due to weather influences and especially UV rays,or contact with tire conditioners can cause the plastic to become brittle and weather over time.Especially with unpainted plastic, this process progresses relatively quickly. PE100 slows down this process and provides intensive protection,which significantly extends the life of the plastic. Also, the likelihood of seals and protective rubbers (e.g. bellows for drive parts) becomingbecome brittle are much lower.In addition to this protective effect, PE100 gives the plastic parts a fresher appearance. PE100 is also excellent for protecting electronic parts frommoisture in electronic parts. Das Produkt bildet eine wasserverdrängende Schicht und verbessert somit den Korrosionsschutz.In the spray can, PE100 is particularly user-friendly and practical to use. Thanks to the special nozzle with tube supplied, even difficult-to-reach areas can be treated effortlessly. Highlights H3>  span> clear, almost invisible fluid div>  span> Easy application div>  span> displaces moisture div>  span> Long-term effect div>  span> protects plastics against discoloring div>  span> holds rubber parts supple and prevents them freeze div>  span> protects ignition systems from moisture-related disorders div> div>> CONTENTS base: silicone oils, mineral oils and additives Density: 710 kg / m³ Consistency: liquid (firefitted in the aerosol can) viscosity: ± 15 mPa.s li> Flash point: 0 ° C compressive strength: minimal li> temperature resistance: -20 ° C to> 150 ° C li> water resistance: good li> acid resistance: resistant to dilute acids li> corrosion protection: good. Corrosion protection results from the formation of a water-displaced layer. Inputs: good li> lubricant content: 17% li> Processing conditions: + 5 ° C to + 40 ° C Underground: Most plastics, rubber and metal USAGEPreparation of the substrate: Provide a clean, dry, grease-free and non-corroded substrate.Shake can well before use. When used as a lubricant, spray the product directly onto the part to be lubricated. When used as a plastic and rubber protector, spray the product directly (spray distance 15-20 cm) or apply with a cloth or sponge. To achieve a beautiful shine, briefly polish the plastic with a clean, dry Multi Wipe. Material cleaning: With Innotec Multisol or Innotec Power Clean Hand cleaning: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water Shelf life: 2 years in unopened original packaging Storage conditions: Store in a cool, dry place Batch code type: F

Genuine FG spare/option part. For use with all foam filters, not for fabric filters.Content1 piece

High performance two-stroke engine oil made of synthetic base oil. For high performance off-road motorcycles. Provides for clean combustion. Premix and oil injected engine use.Synthetic Blend 2-stroke engine oilExcellent combination of selected basis oils and adjsuted additives.Ensures also at extreme loads a secure lubrication and a low fuming combustion.Reduces deposits in the combustion hamber, at piston and piston rings, in the outflow channels and exhaust system and ensures clean spark plugs.Low wear and good corrosion presentationContrary to Panolin's description FG recommend a 3%-4% ratio of mixture for rc-car applications.

Genuine HT spare/option part.Available as 272 high strength and heat resistant, 270/1 high strength or 241 medium strength.The strength of 272 and 270/1 is comparable, but 272 can handle temperatures up to 230°C vs. 150°C for 270/1. It is therefore the perfect choice for applications like exhaust or clutch pinion bolts. However, curing of 272 takes at least twice as long as 270/1.An excellent recommendation for removal of screws treated with threadlocking compound:CFH Diamant M50 Gasbrenner, y1007 Contents:1 piece / 10 gram

Bindulin liquid rubber - very high elasticitySuitable for additional sealing of tuned pipes and exhaust / manifold connections .Temperature resistant from -60 ° to + 180 ° CResistant against diluted acids.Also for sealing threaded joints, electric lines and cable lead-throughs in receiver boxes.The surfaces must be clean, grease free and dry (brake cleaner).Contents:1 piece / 45 grams

Genuine silicone shock absorber oil for the optimal shock absorber set-up. Content: 50 ml Please note: Factory filling of FG/Losi/Smartech and many other 1/5 and 1/6 scale shocks is done with genuine silicone shock absorber oil. To ensure seal tightness and consistency you should only use genuine silicone shock absorber oil for refilling as well.Most every rc-car shock absorber uses silicone oil of different viscosities. The smaller the number, the lower the viscosity of the silicone oil and the softer the damping. As a rule of thumb: Viscosity 100 = similar to water Viscosity 1.000 = similar to cooking oil Viscosity 5.000 = similar to shampoo Viscosity 10.000 = similar to honey As a reference: The red FG Marder / Off-Road Buggy series shock absorbers are factory filled with 2.000 viscosity oil, the shocks on monster cars with dual shock set-ups (total of 8 shocks) are filled with 1.000 viscosity oil, and the shocks on FG onroad cars come filled with 4.000 viscosity oil. The original filling of the Losi 5ive-T is 350cc silicone oil.FG Silicone oil with 50 ml:FG Item N° 6510/010 = Viscosity: 100FG Item N° 6510/025 = Viscosity: 250FG Item N° 6510/035 = Viscosity: 350FG Item N° 6510/050 = Viscosity: 500FG Item N° 6510/075 = Viscosity: 750FG Item N° 6510/100 = Viscosity: 1000FG Item N° 6510/150 = Viscosity: 1500FG Item N° 6510/200 = Viscosity: 2000FG Item N° 6510/300 = Viscosity: 3000FG Item N° 6510/400 = Viscosity: 4000FG Item N° 6510/500 = Viscosity: 5000FG Item N° 6510/600 = Viscosity: 6000FG Item N° 6510/700 = Viscosity: 7000FG Item N° 6510/800 = Viscosity: 8000FG Item N° 6510/900 = Viscosity: 9000FG Item N° 6511 = Viscosity: 10000Viscosity of silicone oil at various temperatures.

Genuine TLR spare/option part.Content:30 ml

Perfect for sealing threads.Resistant against almost all chemicals.Dimensions:Width: 12 mmThickness: 0.075 mmLength: 10 meters