6441 FG Filter oil for foam filter 50ml

€9.90*

Content: 50 Milliliter (€198.00* / 1000 Milliliter)

Prices incl. VAT plus shipping costs

Available

Product number: fg_6441

EAN: 3410564508626

Product information "6441 FG Filter oil for foam filter 50ml"

Genuine FG spare/option part.

For use with all foam filters, not for fabric filters.

Content

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Alternatives

y0284 Air filter oil for foam filters, 50 ml

This air filter oil is designed for lubricating foam filters for on-road and off-road use. It reinforces the filters' efficiency for better carburation and retains dirt, mud and sand particles. Prevents water from penetrating into the filter.It is recommended to put the filter with a little bit oil in a small polybag and work it vigorously by hand. Excessive oil must be pressed out (don't wring the foam!) afterwards.For cleaning the filter please use the special foam cleaner y0523.The filter element must be dry before re-oiling.Content:50 ml

Content: 50 Milliliter (€119.00* / 1000 Milliliter)

€5.95*

y0523 Special cleaner for foam air filters, 500 ml

Genuine rc-car-online spare/option part. Foam-Cleaner, special cleaning agent for foam air filter elements and GPM coverThe foam-Cleaner is specially designed for RC foam air filters, as well as covers for starter, filter and shocks. Removes reliably dirt, mud, dust, old filter oil, and sand particles and ensures optimum air flow. After cleaning please oil the air filter with air filter oil with order-no. y0284 for foam filters before re-use. Routinely cleaning of filters protects against premature wear and extends engine life!Use: apply cleaner to filter/cover, wait for some minutes and rinse with warm water. Let the parts dry before re-use.Bottle with 500 ml.Contents:1 piece

Content: 500 Milliliter (€19.90* / 1000 Milliliter)

€9.95*

y1013 Motul Air filter oil for foam filters

Genuine Motul spare/option part. High-cling oil for foam cartridge air filters, especially for offroad and street use. The oil reinforces the the air filter'e efficiency and retains dirt, mud and sand particles, which will greatly extend the life of the engine. The blue tint makes it easier to control even oil application to the filter.Apply oil to filter generously and work the foam vigorously by hand to ensure complete oil penetration. Press foam slightly to remove excessive oil when done.Contents:1 piece / 400 ml

Content: 400 Milliliter (€47.25* / 1000 Milliliter)

€18.90*

Customers also bought

7357 FG Air filter foam for CY / Zenoah / Fuelie

Genuine FG spare/option part.Contents:2 pieces

€17.90*

y0305 Colored flexible fuel line, top quality, 1 meter

y0305 Color: y0305/04 - Green

High quality flexible fuel line in your choice of blue, red, yellow, orange and green. Size:Length: approx. 1 meterOuter diameter: approx. 6.3 mmInner diameter: approx. 3.2 mmDiameters are 100% identical to the Zenoah Tygon hose #7352!

€5.90*

y0663 Sanyo eneloop XX receiver battery 2500 mAh NiMh, 1 pce.

y0663 Connector: y0663/01 FG-connector+ 7.9EUR

Item N° y0663Sanyo eneloop XX receiver battery 2500 mAh NiMh, 1 pce.Informations about eneloop cells:eneloop XXThe Sanyo eneloop cell eliminates the annoying problem that a charged battery has often lost a high percentage of its storage capacity after just one week. Also, the differences between individual cells in a pack are sometimes significant, reducing the life and performance of the complete pack. Compared to "normal" NiMh cells the Sanyo eneloop cell has a slightly lower capacity and a slightly higher price (in relationship to its capacity), but you get significant advantages in return. With the recently available improved version of the 2005 introduced and widely acclaimed eneloop cell self-discharge for rc-car related time frames is now more or less nonexistent. One could easily charge the cells at New Year?s Eve and use them at Christmas without noticing a significant loss of capacity. Sanyo eneloop cells show a considerably reduced tendency to failure of individual cells in a battery pack. Even after years eneloop cells usually differ by only a few percent. The voltage of the cells is also slightly higher than with normal NiMh cells, so that more volts are available under load. Especially when used in largescale cars with their usually extremely strong servos, this is a particularly important feature! Chargers which are suitable for NiMh cells will also work for eneloop cells. UniversalFGBECHigh currentThe basic features of the eneloop XX version are similar to the standard version, but here the priorities were set slightly different. At the expense of reduced (but easy to cope with for rc-car usage) values for load cycles and self-discharge, capacity could be increased by 25%.- Nominal capacity: 2500 mAh- Maximum number of charge cycles: 500- For cars with up to 3 servos- self-discharge: 25% at 1 yearYou can differentiate the two generations of eneloop cells by checking the model name which is written on each eneloop. The "old" cells have written HR-3UTG (AA) on them, the improved eneloop instead HR-3UTGA (AA)!

Variants from €39.90*

€47.80*

y0657 Receiver battery packs standard size, NiMh, 4500 mAh

y0657 Connector: y0657/01 Futaba, JR, MPX universal

Genuine HT spare/option part. 5 cells, 6 volt, cell size Sub-C. More applications on request.Dimensions: approx 112 x 46 x 23 mmContents:1 piece

€44.90*

6546/01 FG receiver battery Ni-MH 6V/2000mAh

Genuine FG spare/option part.Affordable receiver battery Ni-MH 6V/2000 mAh for the electric power supply of receiver and servos, with JR-Graupner bush, rechargeable.Measures:Width: 112 mmHeight: 46 mmDepth: 23 mmUniversal

€25.90*

Customers also viewed

67350 FG Tuning clutch / Zenoah, set

Item N° 67350 Tuning clutch / Zenoah, setComplete clutch with Tuning carrier, lighter clutch blocks, coated dowel screws and reinforced clutch spring. According to the lighter weight the engine speed is slightly higher when the clutch comes, therefore the engine has more power speeding up.

€65.90*

Details

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€42.90*

FG Sportsline 4WD-510 with Porsche 911 GT3 RSR body

The first 1/5 touring and sports car designed as a 4WD from the ground up. With a wheelbase of 510mm the 4WD chassis is suitable for the FG Mini Cooper and the FG Porsche GT3 RSR bodies. Equipped with a strong 26 cm³ engine, tuning pipe, tank with quick acting closure, 2 differential gears, front disk brake and a lot more. However, the highlight is still the well-known FG 4WD. Maximum traction, easy handling and grip during cornering as well, these are the advantages only a 4WD model can offer.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The RTR version of the car includes servos, transmitter, receiver, rechargeable batteries for transmitter / receiver.The 4WD Sportsline chassis opens up a new era within the Touring and Sportscar class of large scale model cars. Main target was the development of a chassis with supreme driving dynamics and ultimate performance. Maximum traction as well as easy handling, sufficient grip in curves, only a fourwheel powered model offers all these advantages. With the new 4WD Sportsline series FG Modellsport once again sets a trend at 1:5 scale.The 4WD Sportsline chassis for the Porsche 911 GT3 RSR is delivered with a wheelbase of 510mm. The fourwheel drive is carried out over an almost wear resistant tooth belt. 2 differential gears, tank with snap closure and a powerful engine with Tuning pipe turn the Sportsline 4WD chassis into a high-class 1:5 scale model with outstanding driving characteristics.You can choose this 4WD model with painted bodyshell, 2.4 GHz radio control system, servos, batteries in our configurator. Team decals are not included in the delivery content and have to be ordered separately.The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problems. A tank filling enables you to run your model around 45 minutes. Equipment and technical description:Solid 4mm chassis made of high-quality aluminium low-wear belt drive splash-proved 2 differential gears double wishbones at front and rear axle toe-in, castor and wheel camber adjustable at the axles - rear FG ball drive all steel driving components hardened all rotating parts ball-beared servo relieving servo saver front disk brake rear gear brake with big brake disk 700ccm fuel tank with snap closure oil-pressure shock absorbers with volume control and spring adjusting ring 26 cm³ combustion engine with Tuning pipe fabric hollow chamber tires with inserts receiver box and battery holder polycarbonate bodyshell 2.4 GHz pistol grip radio control system with steering and gas servo.Dimensions: Length: 980 mm Width: 405 mm Height: 250 mm Wheelbase: 510 mm Touring cars in action!Painting tips:

From €1,299.95*

Configure now

y19752 Tire tread cutter spare Blades, 5pcs.

Even though the blade will keep its edge for a long time, no cutting tool will last forever. Spare blades are available of course.Cutting width approx. 3 mmPack of 5

€9.90*

%

TT1030 Top Tuning CAR-STAND for 1/5, 1/6, 1/8, 1/10

Ideal work stand with extra wide tripod up to 100 kg. load capacity with excellent stability, even on uneven (!) urface.Specially made support mechanism, individually adjustable width from 115 mm to 375 mm for most RC cars from 1/10 to 1/5 scale. incline from 0 to 90° Quickly folded and loaded For easy storage, as well as for transport completely foldable! (Carrying bag available!)Height adjustment of the support from 635 mm to 1000 mm and inclination from 0-90° Length of the support surface 386 mm Bis zu 100Kg belastbar! Support mechanism continuosly adjustable in width Due to various adjustment options, the Top Tuning CAR STAND offers the optimal possibilities for making adjustments or maintenance work on the RC car. The load capacity and stability are beyond doubt with a load limit of 100 kg and the extremely stable tripod. The up to 90 ° adjustable slant shows your RC car at events and presentations, as well as in your assembly room to its best advantage! 6.5 kg. weight Pivoting bracket Height adjustable from 69 to 104 cm Basic frame is made of steel, painted or chromed Car bracket is made of aluminum and stainless steel A tool holder TT1030/01 is also available as an accessory in our shop selection.

€179.90* €199.99* (10.05% saved)

Configure now