Wire looms, male, 1 pce

rc-car-online

€4.10*

Prices incl. VAT plus shipping costs

Available

kabelbaum_stecker Version

Product number: kabelbaum_stecker.3

EAN: 4058575017103

Product information "Wire looms, male, 1 pce"

Wire looms for servos and battery packs, male connector.

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

No reviews found. Share your insights with others.

Similar products

y0735 Safety clip for Universal / JR / Futaba connectors

Genuine HT spare/option part. Protects the mated connection to prevent them from coming apart accidentally. Particularly recommended for direct power supply cords, as a tensile load on the cable can remove the link unnoticed and then you would perhaps think of a servo failure in the first place.The small size usually allows the installation even inside the receiver box.Also suitable for securing the connection of the receiver battery; the use of this clip means a big improvement in safety with little effort.Contents:1 piece

€1.50*

6547 FG Receiver cable FG gold contact/Futaba - 1pce.

Receiver cable, ready-made with FG gold contact plug-in system for Futaba plug.total length 20-25cm

€17.90*

y0425/01 Y-harness, silicone insulated, universal/JR

Genuine HT spare/option part. The Y-harness is required for running two servos on a single receiver channel. Top quality heavy gauge 0.5 mm² cable with silicone insulation, 150 mm long, suitable for all rc-systems.Content:1 piece

€12.90*

6545 FG gold contact plug-in system 2mm - 2pcs.

Item N° 6545 FG gold contact plug-in system 2mm - 2pcs.Reverse battery protected gold contact plug-in system. A further great advantage of our plug-in system is the fixing of a plug on the receiver box or rc-plate with screws. This makes the connection of plug and bush easier.

€7.90*

y0428 Extension cable universal180/300 mm

y0428 Length: y0428/01 - 180 mm

In case the servo cable is not long enough.Two selectable lengths:y0428/01 - 180 mmy0428/02 - 300 mm

€5.90*

6545/01 FG gold contact plug-in system 2mm - 10pcs.

Item N° 6545/01 FG gold contact plug-in system 2mm - 10pcs.Reverse battery protected gold contact plug-in system. A further great advantage of our plug-in system is the fixing of a plug on the receiver box or rc-plate with screws. This makes the connection of plug and bush easier.

€39.90*

y1306 JETI-SBEC 6-42V voltage regulator

The switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piece

€74.90*

This product is currently not available.

6547/01 FG Receiver cable FG gold contact/Multiplex - 1pce.

Receiver cable, ready-made with FG gold contact plug-in system for Multiplex plug.total length 20-25cm

€7.10*

y0424 Extension cable, Futaba/universal

akku_0019 Length: y0424/02 - 25 cm+ 2.5EUR

Genuine HT spare/option part. In case the servo cable is not long enough.Two selectable lengths:y0424/01 - 10 cmy0424/02 - 25 cmContents:1 piece

Variants from €6.80*

€9.30*

Wire looms, male, 1 pce

kabelbaum_stecker Version: y0292 MPX Servo old system+ 2.2EUR

Wire looms for servos and battery packs, male connector.

Variants from €4.10*

€4.90*

y0533 Adapter cable for LRP Jet-Pro Charger

y0533 Battery connector: y0533/01 - BEC to Universal female

Genuine HT spare/option part. Adapter cable for all usual rx-battery connectors, especially for use with the LRP Jet-Pro charger.Available applications:BEC to UniBEC to FGBEC to High CurrentBEC to Uni femaleContents:1 piece

€5.90*

y1303/05 EC3 connector to Universal female

Adapter EC3 male to Universal female.Adapter cable for the LiPo receiver battery in late model Losi 5ive-T and Losi Mini WRC.Dimensions:Length cable: 50 mmTotal length: 85 mmContent:1 piece

€9.90*