Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey and Super Rock Rey.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: The adapters only fit in combination with the standard plastic steering knuckles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which then prevents the drive pin from being fitted.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fender wells will need some cutting.Please note: the wide rear wheels from MadMax or HPI do not fit!This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Genuine FG spare/option part.Square wheel driver in high-strength alloy material with M6 fixing thread. Essentially higher retention force. Suitable for all models.Dimensions:14 mm wide18mm squareBore diameter 8 mmContent:2 pieces

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces

Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey, Super Baja Rey 2.0 and Super Rock Rey. Suitable for 8 mm axles.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: These adapters only fit in combination with the optional aluminum spindles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which requires different dimensions for the wheel drives.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fenderwells will need some cutting. Please note: the wide rear wheels from MadMax or HPI do not fit! This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm

Genuine HT spare/option part.This adaptor allows you to install all MadMax/HPI tire/rim combinations on FG, Carso, Smartech 2WD/4WD and other cars with the same wheel shaft configuration. Losi 5ive tires can be used as well, but they hey have to be mounted on MadMax/HPI rims because Losi rims are too thick at the center. The adapter is drilled for 8 mm wheel shafts (FG, Smartech/Carson and many more!), hex size of wheel drive and wheel nut is 24 mm hex with M18x1.0 thread (same as HPI).Please note:FG wheel shafts come with either M6 or M8 thread size. It can even happen that a vehicle has different thread sizes front and rear! Therefore, please make sure which version is required before placing an order.Converting your car takes only a couple of minutes with this easy to install adaptor. just see picture "installation instruction" for a schematic installation.Contents:2 pieces

Wheel squares with 3 mm dowel pins. The pins prevent the squares from damaging the rims under high load. For all FG rims, holes may have to be drilled.11,5mm wide.Bore diameter 8 mm18 mm square

Genuine FG spare/option part. Square wheel driver in high-strength alloy material with M6 fixing thread. Essentially higher retention force. Suitable for all models.Dimensions:Square: 18 mm Width: 17 mmBore: 8 mmContents:2 pieces

Suitable for all FG front uprights. The use of this front axle prevents a pressing and jamming of the inner ball bearing rings when tightening the wheel. Suitable for square wheel driver 9,5mm and 14mm.

Genuine FG spare/option part. Square wheel driver in high-strength alloy material with M6 fixing thread. Essentially higher retention force. Suitable for all models.Dimensions:Square: 9,5 mm Width: 17 mmBore: 8 mmContent:1 pieces:

Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP RC, increase track width for 25 mm and allow for the use of HPI 5T, Losi 5ive-T, 5ive-B and Mini rims. 5 mm o-rings protect against drive pin loss. Set of four inclusive o-rings, drive pins and closed wheel nuts (wrench size 24 mm!).Contents:1 set

Genuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi 5ive tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.LosiDBXL rims do not fit the X-Maxx (depth of hex is too deep)!Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces

Genuine Losi spare/option part.Fits Losi 5ive-T, TLR 5ive-B and 5ive Mini.Dimensionally identical with B55015Content:2 pieces

Genuine Hurrax spare/option part.17 mm hex wheel drives, 19 mm wide with 8 mm bore diameterm. Weight 20 grams.Contents:2x Adaptor4x Grub screws M 5x5 mm

Genuine FG spare/option part. Content:2 pieces

Genuine HT spare/option part.Rim reinforcement, transfers the load over a larger diameter into the rim and protects the rim's square. Will also allow for the use of rims with an already damaged square.For FG Off-Road rims 60200, 60201 (wide) and 60205, 60206 (narrow).14 mm wide square drives must be used.Please note:When installed with new (unused) rims, it may be necessary to modify the rim's square slightly.Contents:2 piece

Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces

Item N° 08610/02 Square wheel driver 14mm f. 08610/01, 2pcs.Suitable for all FG front uprights with FG No. 8610/01 Front axle with collar, 1pce.

Genuine HPI spare/option part. For HPI Baja 5SC, fits too for HPI Baja 5B, 5B 2.0 and 5T(GUNMETAL/2pcs) These 24mm HD front hex hubs replace the stock hubs on HPI Baja 5B and 5T vehicles for extra durability. First introduced on the Baja 5SC truck, these heavy duty front hubs use a screw & nut design that eliminates the previous use of an e-clip. They're precision machined from billet aluminum for a perfect fit and gunmetal anodized for custom looks.Color: gunmetal.Contents:2 pieces

Genuine ARRMA spare/option part. Contents:2 pieces

Genuine HPI spare/option part. Color: Gunmetal.Contents:2 pieces

Genuine HPI spare/option part. Color: Purple.Contents:2 pieces