Skip to main content
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

8610/02 FG Square wheel driver 14mm f. 08610/01, 2pcs.

Product information "8610/02 FG Square wheel driver 14mm f. 08610/01, 2pcs."

Item N° 08610/02
Square wheel driver 14mm f. 08610/01, 2pcs.


Suitable for all FG front uprights with FG No. 8610/01 Front axle with collar, 1pce.

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Accessories / Spare parts

Average rating of 0 out of 5 stars

8610/01 FG Front axle with collar, 1pce.
Item N° 08610/01 Front axle with collar, 1pce.Suitable for all FG front uprights. Suitable for square wheel driver 9,5mm and 14mm. Dimensions: Shaft: 8 mm Outside thread: M6 Inside thread: M4 Total length: 58 mm

€11.50*

Alternatives

Average rating of 0 out of 5 stars

8610/10, FG Front axle w/h collar/ Square wheel driver 14 mm, set
Suitable for all FG front uprights. The use of this front axle prevents a pressing and jamming of the inner ball bearing rings when tightening the wheel. Suitable for square wheel driver 9,5mm and 14mm.

€23.00*

Similar products

Average rating of 0 out of 5 stars

8610/10, FG Front axle w/h collar/ Square wheel driver 14 mm, set
Suitable for all FG front uprights. The use of this front axle prevents a pressing and jamming of the inner ball bearing rings when tightening the wheel. Suitable for square wheel driver 9,5mm and 14mm.

€23.00*

Average rating of 0 out of 5 stars

y6107/01 Wheel squares 18 mm HART-COAT, 14 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€17.45*

Average rating of 0 out of 5 stars

y6107/02 Wheel squares 18 mm HART-COAT, 17 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€18.95*

Average rating of 0 out of 5 stars

6106/07 FG Wheel square 11,5mm - 2pcs.
Wheel squares with 3 mm dowel pins. The pins prevent the squares from damaging the rims under high load. For all FG rims, holes may have to be drilled.11,5mm wide.Bore diameter 8 mm18 mm square

€23.90*

Average rating of 0 out of 5 stars

y0521 Madmax/HPI-rim to FG-car wheel adaptor
y0521 Version: y0521 - for M6 wheel shafts
Genuine HT spare/option part.This adaptor allows you to install all MadMax/HPI tire/rim combinations on FG, Carso, Smartech 2WD/4WD and other cars with the same wheel shaft configuration. Losi 5ive tires can be used as well, but they hey have to be mounted on MadMax/HPI rims because Losi rims are too thick at the center. The adapter is drilled for 8 mm wheel shafts (FG, Smartech/Carson and many more!), hex size of wheel drive and wheel nut is 24 mm hex with M18x1.0 thread (same as HPI).Please note:FG wheel shafts come with either M6 or M8 thread size. It can even happen that a vehicle has different thread sizes front and rear! Therefore, please make sure which version is required before placing an order.Converting your car takes only a couple of minutes with this easy to install adaptor. just see picture "installation instruction" for a schematic installation.Contents:2 pieces

€39.90*

Average rating of 0 out of 5 stars

6107 FG Wheel square 9,5mm/M6
Genuine FG spare/option part. Square wheel driver in high-strength alloy material with M6 fixing thread. Essentially higher retention force. Suitable for all models.Dimensions:Square: 9,5 mm Width: 17 mmBore: 8 mmContent:1 pieces:

€15.90*

Average rating of 0 out of 5 stars

6107/02 FG wheel square 17 mm/M6
Genuine FG spare/option part. Square wheel driver in high-strength alloy material with M6 fixing thread. Essentially higher retention force. Suitable for all models.Dimensions:Square: 18 mm Width: 17 mmBore: 8 mmContents:2 pieces

€16.90*

Average rating of 0 out of 5 stars

TT1051 Top Tuning Conversion kit for the standard 1:/5 18 mm square wheel drives for the Carson CY-Eline cars
Genuine Top Tuning spare/option part. Conversion kit for the standard 1:/5 18 mm square wheel drives for the Carson CY-Eline carsThis allows for the use of all 1/5 on-road wheels e.g. by or . The cars become approx. 5 mm wider per side. This i feasibles with all usual body shells of the CY-E-line cars. Set includes:4 pieces # y6107 hard coated 18 mm aluminum square drives, 9.5 mm wide, with 8 mm axle bore, threaded for 2 x M6 grub screws4 pieces M6 grub screws8 pieces 3x16 mm steel pins4 pieces # 6038 mounting washers 6x15 mm 4 pieces M5x16 mm countersunk screws

€39.90*

Average rating of 0 out of 5 stars

6107/01 FG wheel square 14 mm/M6
Genuine FG spare/option part.Square wheel driver in high-strength alloy material with M6 fixing thread. Essentially higher retention force. Suitable for all models.Dimensions:14 mm wide18mm squareBore diameter 8 mmContent:2 pieces

€16.90*

Average rating of 0 out of 5 stars

y6106/07 Wheel square 11,5mm, steel
Two wheel squares with 3mm dowel pins. Like FG 6106/07, but made from heat treated steel. Significantly reduced wear. The pins prevent the squares from damaging the rims under high load. For all FG rims, holes may have to be drilled. Pins should be fitted using high strength thread locking compound.Measures:18 mm square11.5mm wideBore diameter 8 mm

€19.90*

Average rating of 0 out of 5 stars

y6107/07 Wheel squares 18 mm HART-COAT, 12 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces

€16.45*

Average rating of 0 out of 5 stars

50100000 Lightscale nut spanner for Lightscale Lock wheel nuts, 1 pce.
The special tool for Lightscale wheel nuts is simply inserted into the end of a spark plug wrench and is secured there by use of an o-ring. With its 3 hardened pins the tool locates into the wheel nut and may be used to tighten or untighten it. The tool is universally usable for all Lightscale wheel nuts.The kit contains the tool as well as the o-ring and hardened pins. The tool comes ready for use. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.

€21.50*

Customers also viewed

Average rating of 0 out of 5 stars

2012-37 Mecatech Square wheel Driver 12 mm
Genuine Mecatech spare/option part for the FW01.Content:2 pieces

€13.80*

Average rating of 0 out of 5 stars

6107/07 FG Alum.square wheel driver 12mm/M6
Genuine FG spare/option part. Content:2 pieces

€16.90*

Average rating of 0 out of 5 stars

3000-14 Mecatech Expert piston spring - set

€12.90*

Average rating of 0 out of 5 stars

154100E FG Sportsline 4WD Electro 530er Wheelbase
Genuine FG spare/option part. The following items are required for completion: electric motor, ESC, steering servo, radio system, body mounts, body, LiPo driving batteries and charger.

€689.95*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Agency