Product information "TT1044 Top Tuning 24 mm hex wheel drives for Losi Super Baja Rey, 2.0 and Super Rock Rey / aluminum spindles"
Genuine Top Tuning spare/option part.
TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey, Super Baja Rey 2.0 and Super Rock Rey. Suitable for 8 mm axles.
The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.
Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!
Please note: These adapters only fit in combination with the optional aluminum spindles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which requires different dimensions for the wheel drives.
As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread. Depending on tire size the rear of the fenderwells will need some cutting.
Please note: the wide rear wheels from MadMax or HPI do not fit!
This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.
Weight per piece 28 grams (original LOS25077 weighs 23 grams).
Contents:
2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum
2 pieces of hardened drive pins 3x23,8 mm
0 of 0 reviews
Average rating of 0 out of 5 stars
Leave a review!
Share your experiences with other customers.
Login
No reviews found. Share your insights with others.
Genuine Top Tuning spare/option part. Motor pinion made of nitrided hardened steel, module 1.5 and 8 mm bore. Reinforced hub for set screw M5x6. The pinions with odd tooth counts are profile shifted. Within the same outer diameter, there is no need to adjust the backlash when changing the pinion. When mounting on vehicles with mounting holes in the motor mount that are specific to the tooth count, the mounting holes for the higher number of teeth in each case (16 or 18) must be used.Profile regraded:This means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter. Available in two sizes with two tooth counts:Outer diameter 30 mm with 17T or 18TOuter diameter 27 mm with 15T or 16TContents:1 piece
SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 24 mm hex wheel drive, 20 beadlock screws per rim and reinforced orangen beadlock rings. Fits Losi 5ive-T, 5ive Mini, Desert Buggy XL and all HPI Baja 5B and 5T/SC cars.Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.) On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks!MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part Some off-road tires knowledge can be found here!
TARMAC BUSTER 170x80 and 170x60 with black MadMax Extreme rims with 20 beadlock screws, with 24 mm hex socket and reinforced orange beadlock rings for Losi 5ive-T and Desert Buggy XL as well as all HPI Baja 5 cars. Due to the extreme load created by the MadMax TARMAC BUSTER tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars like the Losi 5ive-T. The TARMAC BUSTER MadMax are designed for use on flat surfaces. Your car will have good traction even on smooth pavement!We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel drive Some off-road tires knowledge can be found here!
CROSS BOND 170 x 80 mm and 170 x 60 mm tires with black MadMax Extreme 20 bolt-beadlock rims with 24 mm hex drive and reinforced orange beadlock rings were designed for use on loose surfaces. The extremely rigid and differently structured lugs of the CROSS BOND ensure optimum power transmission and also allow for excellent grip on loose surfaces, such as sand and soil. The lugs are raised at the treads outside, and therefore provide maximum grip, particularly when cornering where the tire is canted to the outside. Due to the extreme load created by the MadMax CROSS BOND tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars. We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex driveThe video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!
Regular price: 129,90 EURoffer of the month price: 89,90 EURUltragrip 170x80 and 170x60 on black MadMax Extreme rims with 20 beadlock screws, with 24 mm hex socket and reinforced orange beadlock rings for Losi 5ive-T and Desert Buggy XL as well as all HPI Baja 5 cars.150 shifted long lugs and a central, 4 mm high ridge on the 60 mm wide front tire, and 210 pieces of square 6 x 4 mm studs on the 80 mm wide rear tire ensure optimal propulsion! The flattened profile structure of the rows of knobs reduces the directional control and guarantees an exceptionally good on-center feel! This makes the car less prone to unwanted traction rolls! Due to the extreme load created by the MadMax Ultragrip tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars like the Losi 5ive-T.The complete set includes two each 60 mm and 80 mm tires, or two pairs 60 mm tires for Losi 5ive T in a body covered with wheels (like the original body), with inserts and MadMax EXTREME rims! We recommend to check the beadlock screws after the run. Dimensions:Outside diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel driveThe video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!
Genuine GPM spare/option part. Stainless steel replacement bolts fit not only GPM driveshafts SB237S, but Losi stock driveshafts LOS252072 and LOS252110 as well. Contents:2 pieces / 1 pair
Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaftSuitable for all servos with an output shaft with 15 tooth spline shaft, for example:K-Power DM4000Multiplex RhinoHitec 805Savöx SV-0236MGSpektrum S9010 and S9020LOSB 0886 S901T (Original Losi 5ive-T throttle Servo servo)LOSB 0884 S900S (Original Losi 5ive-T steering servo)Losi SPMS904 WPand many more!holes for linkage with M4 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.Content:1 pieces
GIANT GRIP 190 x 70 with black colored MadMax Extreme rims, 20-fold screwed, very tough, with 24 mm hex drive and reinforced orange beadlock rings for Losi 5ive-T and Desert-Buggy XL as well as all HPI Baja 5 B/T cars.The GIANT GRIP provides giant traction through 96 about one cm² wide and 5 mm high strong lugs, getting ample grip even on loose surfaces like sand and soil.Due to the extreme strain caused by the GIANT GRIP tires the MadMax rim with reinforcement ring had to be optimized once more.The GIANT GRIP tires come with strong special tire inserts which allow to transfer the power without canting, even on heavy cars like the Losi 5ive-T.Dimensions:Outer diameter: 190 mmTire width at bead 70 mmTread width 80 mmReinforced 24 mm hex wheel driveThe MadMax Giant Grip tires use 60 mm wide rims ( y1415/01 or y0761/01).The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!
Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey and Super Rock Rey.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: The adapters only fit in combination with the standard plastic steering knuckles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which then prevents the drive pin from being fitted.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fender wells will need some cutting.Please note: the wide rear wheels from MadMax or HPI do not fit!This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm
Genuine HT spare/option part.This adaptor allows you to install all MadMax/HPI tire/rim combinations on FG, Carso, Smartech 2WD/4WD and other cars with the same wheel shaft configuration. Losi 5ive tires can be used as well, but they hey have to be mounted on MadMax/HPI rims because Losi rims are too thick at the center. The adapter is drilled for 8 mm wheel shafts (FG, Smartech/Carson and many more!), hex size of wheel drive and wheel nut is 24 mm hex with M18x1.0 thread (same as HPI).Please note:FG wheel shafts come with either M6 or M8 thread size. It can even happen that a vehicle has different thread sizes front and rear! Therefore, please make sure which version is required before placing an order.Converting your car takes only a couple of minutes with this easy to install adaptor. just see picture "installation instruction" for a schematic installation.Contents:2 pieces
Genuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi 5ive tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.LosiDBXL rims do not fit the X-Maxx (depth of hex is too deep)!Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces
Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP RC, increase track width for 25 mm and allow for the use of HPI 5T, Losi 5ive-T, 5ive-B and Mini rims. 5 mm o-rings protect against drive pin loss. Set of four inclusive o-rings, drive pins and closed wheel nuts (wrench size 24 mm!).Contents:1 set
Item N° y1183/02FG rim to HPI model, drive rim adapter, separate for the front, 2 pcs.These adapters are machined from gas nitrited steel and enable you to put standard rims with 18 mm square drive (FG, Carson, Lauterbacher a.s.o.) on the HPI Baja 5B/SS/T. The track width will be substantially increased.For a complete set covering front and rear axle you need part number y1183.This set includes rim adapters with installation hardware for the front axle only.Measures for front:Outer diameter: circa 17,59 mLength: circa 55,10 mm
Genuine HT spare/option part.Rim reinforcement, transfers the load over a larger diameter into the rim and protects the rim's square. Will also allow for the use of rims with an already damaged square.For FG Off-Road rims 60200, 60201 (wide) and 60205, 60206 (narrow).14 mm wide square drives must be used.Please note:When installed with new (unused) rims, it may be necessary to modify the rim's square slightly.Contents:2 piece
The special tool for Lightscale wheel nuts is simply inserted into the end of a spark plug wrench and is secured there by use of an o-ring. With its 3 hardened pins the tool locates into the wheel nut and may be used to tighten or untighten it. The tool is universally usable for all Lightscale wheel nuts.The kit contains the tool as well as the o-ring and hardened pins. The tool comes ready for use. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Wheel nut rear for F1 Cars using M6 Thread on the axle.The Lightscale wheelnut is used in combination with the Lightscale lexan disc to convert F1 rims to an up to date and modern look.Thereby the Lightscale wheel nut works just like a real one in present f1 racing. It is tightened with a 22 open end spanner or socket wrench. Alternatively one may use the special Lightscale toolto tighten or loosen the wheel nut.Due to the use of rifled and conical washers a locking effect is achieved.Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The kit contains two wheel nutsas well as four rifled conical washersOptional parts: Tool for Lightscale wheel nuts (item code two wheel nutsas well as four rifled conical washersOptional parts: Tool for Lightscale wheel nuts (item code 50100000)
Wheel nut front for F1 Cars using M6 Thread on the axle.The Lightscale wheelnut is used in combination with the Lightscale lexan disc to convert F1 rims to an up to date and modern look.Thereby the Lightscale wheel nut works just like a real one in present f1 racing. It is tightened with a 22 open end spanner or socket wrench. Alternatively one may use the special Lightscale tool to tighten or loosen the wheel nut.Due to the use of rifled and conical washers a locking effect is achieved.The kit contains 2 wheel nuts as well as 4 rifled conical washers.Optional parts: Tool for Lightscale wheel nuts item code 50100000, Lightscale lexan disc item code 51009500 and spare rifled conical washers item code 881200058801. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Genuine HT spare/option part.Rim reinforcement, transfers the load over a larger diameter into the rim and protects the rim's square. Will also allow for the use of rims with an already damaged square.For FG Off-Road rims 6105, 6105/01 (white) and 3105 (silver).14 mm wide square drives must be used.Please note:When installed with new (unused) rims, it may be necessary to modify the rim's square slightly.Contents:2 pieces
Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey and Super Rock Rey.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: The adapters only fit in combination with the standard plastic steering knuckles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which then prevents the drive pin from being fitted.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fender wells will need some cutting.Please note: the wide rear wheels from MadMax or HPI do not fit!This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm
Completeset inclusive: 2x TT1530/450 Top Tuning 5000 mAh LiPo Batterie 4S, 14,8V 60C 2 x TT1499 Top Tuning Safety Bag for LiPo Batteries The Losi® Super Baja Rey 2.0 with Spektrum Smart is the new standard in 1/6th-scale desert trucks. Overpowered and over-the-top, the SBR 2.0 takes it to the next level of performance and scale detail.Key Features Officially Licensed Method Wheels and BFGoodrich Tires Officially Licensed Brenthel Trophy Truck Body 50+ MPH Spektrum Firma 8s 1/6 750kv Brushless Motor 3 Separate Mounted LED Lightbars Spektrum Features Licensed Method Racing Beadlock Wheels Licensed BFGoodrich Mud-Terrain T/A KM3 Bottom Loading Battery Tray New Brenthel Body and Cage work with dual spare tires AVC - Active Vehicle Control System New Front Suspension Arms and Slider Front driveshafts Long Travel Suspension King Coil-Over Oil Filled Shocks with new springs 8S Capable Motor and ESC Longer Rear Trailing arm with increased wheelbase Shaft Driven 4wd Drivetrain Updated HV capable S905 Lage Scale Steering Servo New Front Bumper with realistic lower valance and Brenthel logo New stiffer front sway bar LED Lights Scale Details Spektrum DX3 Radio System Overview The Losi® Super Baja Rey 2.0 with Spektrum Smart is the new standard in 1/6th-scale desert trucks! With powerful performance and incredible scale looks, the SBR 2.0 takes it to the next level! Taking the Super Rock Rey chassis, adding about an inch to the wheelbase and morphing it with the front end from the Super Baja Rey gets you the all new and improved Super Baja Rey 2.0! You get the best of both worlds! The Spektrum Firma SMART 160 Amp 8S ESC and 750kv Firma 1/6th 5687 brushless motor allow you to unlock blazing speeds. The bottom loading chassis makes battery changes a breeze. Front and rear LED light bars keep everything nice and bright for off-road adventures at night. Drivers stay in control with a DX3 transmitter, a Spektrum 6100AT AVC® receiver with steering priority, and officially licensed Method Racing Beadlock Wheels and BFGoodrich Mud-Terrain T/A KM3 tires. The new Brenthel Trophy Truck body is modeled after their actual race truck providing an aggressive, scale-detailed look. The Losi® Super Baja Rey 2.0 is the ultimate desert truck with scale looks, insane speeds, performance and Spektrum Smart Dimensions Height: 305 mm Length: 889 mm Width: 396 mm Weight: 9,8 kg Officially Licensed Method Racing Beadlock Wheels New 17mm hex licensed Method Racing Bead Lock Wheels allow you to replace and update the tire or foam inserts without damage to the tire or wheel. Officially Licensed BFGoodrich Mud-Terrain T/A KM3 BFGoodrich is synonymous with Off-Road Racing. New licensed bead-lock BFGoodrich Mud-Terrain T/A KM3 tires! It doesn"t get any more official! Bottom Loading Battery Tray To help withstand the trials and tribulations of off-road driving, the Super Baja Rey desert truck incorporates our innovative bottom-loading battery system, which allows you to change the batteries without removing the body. Quickly and easily make battery changes without removing the body or wrestling with battery straps. Aluminum Chassis The foundation of the Super Baja Rey 2.0 consists of a 4mm, anodized aluminum chassis plate with a 4mm upper deck. For added durability and performance it"s integrated with a realistic roll cage made of super-tough composite material. Whether you are hitting the whoops, getting huge air, or just wide open, the 4mm chassis just keeps asking for more! Officially Licensed Brenthel Trophy Truck Body New Brenthel Trophy Truck body modeled after their actual race truck. The hood scoop and fender vents will provide an aggressive off-road look. Scale Details You also get a molded interior that includes a driver and co-driver, both of which sport racing helmet and harness details. Along with scale detail accents like fire extinguishers, shock reservoirs, fans and a jack. Full Bodied Roll Cage Just like the 1:1 desert trucks, the Super Baja Rey 2.0 comes with a super-rigid roll cage made of super-tough composite material that enhances the truck"s scale looks and durability. It is integrated with the 4mm anodized aluminum chassis plate providing the ultimate protection for your truck and electronics. New Front Suspension Arms and Slider Front Driveshafts The front suspension arms have been redesigned on the SBR 2.0 to accommodate the slider style front axles. This allows us to run more suspension travel so we can hit the roughest terrain. Long Travel 4-link Rear Axle The Super Baja Rey 2.0 rear suspension allows it to soak up massive whoops and bumps with the same realistic handling and movement of a full-scale desert truck. You get better control and a more locked-in feel regardless of the terrain. Coil-Over Oil Filled Shocks King Shocks long Travel Coil-Over Oil filled shocks with bump stops can handle anything you throw at the SBR 2.0. From hard pack to whoops, Small rollers to giant kickers, these shocks absorb it all! Spektrum Firma Smart 8S - Capable 160A Waterproof ESC Firma Smart ESCs do much more than regulate power. They function like a virtual engineer inside your model, providing a direct path to the vital operating data you need to reach peak performance. Firma Smart ESCs give you an extra layer of confidence that your electronics are all operating at their best. 50+ MPH Spektrum Firma 8S 1/6 750Kv Brushless Motor The brushless Spektrum Firma 4-Pole 750Kv 550 Motor will provide excellent power (50+ MPH) on 8S LiPo (not included). Longer Wheelbase and Rear Trailing Arm New longer rear trailing arms increase the wheelbase and add stability over rough terrain at high speeds. This also provides additional suspension tuning options 4X4 Driveline with Adjustable Differentials Full-time four-wheel drive provides amazing traction. Additionally the front, center and rear differentials can be tuned allowing adjustment of the power bleed between the front and rear drivetrain. The power bleeds evenly front-to-rear and the truck will drive out of the turns harder from point to point. The tunable differentials allow you to dial in your truck for maximum performance and traction. Large Scale Steering Servo The new Spektrum S905 HV capable waterproof servo updates the SBR 2.0. The massive torque from this servo keeps you headed in the right direction. Dual Spare Tires Blow out a tire out on the flats? No worries. The SBR 2.0 comes equipped with functional dual spare tires. Easily add the tire and get back to tackling the terrain. Front Grill Mounted LED Lights The fun doesn"t stop even when the sun goes down with the Super Baja Rey 2.0. Brilliant LED lights integrated into the front grill cast more than enough illumination for running at night. Front Roll Cage Mounted LED Lights The LED"s don"t just stop at the front grill, as a larger set are mounted on the top of the roll cage just under the roof line. Rear Roll Cage Mounted LED Lights Continue to light up the night even after you"ve blown by the competition. Spektrum DX3 Radio System The Spektrum DX3 radio system offers advanced features like AVC control, a 3-position throttle limiting switch and travel adjust.
Genuine FG spare/option part.Suitable for the FG GT1 models with a width of 420mm, f.e. CLK-GTR, Porsche GT1, GT2, GT3, for the Formula 1 and all 1:6 Buggy and Monster models. For rear axle only! 4WD cars must use GPM ball drive set GPM66275 for the front.For Marder and Beetle models until Nov'03 the raised uprights 6077 bzw. 6478 are needed.Content:1 set
€135.95*
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).