Skip to main content
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

8610/10, FG Front axle w/h collar/ Square wheel driver 14 mm, set

Product information "8610/10, FG Front axle w/h collar/ Square wheel driver 14 mm, set"

Suitable for all FG front uprights.

The use of this front axle prevents a pressing and jamming of the inner ball bearing rings when tightening the wheel.

Suitable for square wheel driver 9,5mm and 14mm.

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Accessories / Spare parts

Average rating of 0 out of 5 stars

8610/01 FG Front axle with collar, 1pce.
Item N° 08610/01 Front axle with collar, 1pce.Suitable for all FG front uprights. Suitable for square wheel driver 9,5mm and 14mm. Dimensions: Shaft: 8 mm Outside thread: M6 Inside thread: M4 Total length: 58 mm

€11.50*

Average rating of 0 out of 5 stars

8610/02 FG Square wheel driver 14mm f. 08610/01, 2pcs.
Item N° 08610/02 Square wheel driver 14mm f. 08610/01, 2pcs.Suitable for all FG front uprights with FG No. 8610/01 Front axle with collar, 1pce.

€13.90*

Alternatives

Average rating of 0 out of 5 stars

y6107 Wheel squares 18 mm HART-COAT, 9,5 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€14.95*

Average rating of 0 out of 5 stars

y6107/01 Wheel squares 18 mm HART-COAT, 14 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€17.45*

Average rating of 0 out of 5 stars

y6107/02 Wheel squares 18 mm HART-COAT, 17 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€18.95*

Average rating of 0 out of 5 stars

y6107/07 Wheel squares 18 mm HART-COAT, 12 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces

€16.45*

Customers also bought

Average rating of 0 out of 5 stars

10530/02 FG Replacement friction pads for 10530
Genuine FG spare/option part. Spare part for .

€53.90*

Average rating of 0 out of 5 stars

y0723 Gas-nitrited tuning clutch bell for FG, Smartech/Carson, Harm, RS5 & Co.
Genuine HT spare/option part. Gas-nitrited tuning clutch bell; machined from high grade steel with vents for cooling of the clutch system and holes for easy clutch adjustment. The clutch bell features a significantly reinforced wearing surface which guarantees dimensional stability even under high loads!For best mounting of the pinion the clutch bell shaft has to flats with a 90° offset. As an additional safety device a M5 bolt with washer (included) replaces the E-clip found on stock clutch bells.Suitable for many 1/5 and 1/6 cars, such as all FG (except Formula 1), Carson a.s.o.Contents:1 piece

€49.90*

Average rating of 0 out of 5 stars

y0809 Klüber high performance grease for differentials
Freaking expensive, but it is damned fine.ASONIC HQ 72-102 is a synthetic high-temperature lubricating grease, for use in limited slip differentials. Due to the careful selection of product components and the clean manufacturing environment, ASONIC HQ 72-102 is a rolling bearing grease with a particularly low noise level.Benefits for your application:High-temperature lubricating grease for rolling bearingsHigh purityLow noiseGood water resistanceContent:1 piece, tube with 30g

Content: 30 Gramm (€730.00* / 1000 Gramm)

€21.90*

Average rating of 0 out of 5 stars

y0523 Special cleaner for foam air filters, 500 ml
Genuine rc-car-online spare/option part. Foam-Cleaner, special cleaning agent for foam air filter elements and GPM coverThe foam-Cleaner is specially designed for RC foam air filters, as well as covers for starter, filter and shocks. Removes reliably dirt, mud, dust, old filter oil, and sand particles and ensures optimum air flow. After cleaning please oil the air filter with air filter oil with order-no. y0284 for foam filters before re-use. Routinely cleaning of filters protects against premature wear and extends engine life!Use: apply cleaner to filter/cover, wait for some minutes and rinse with warm water. Let the parts dry before re-use.Bottle with 500 ml.Contents:1 piece

Content: 500 Milliliter (€19.90* / 1000 Milliliter)

€9.95*

Average rating of 0 out of 5 stars

6113 FG Wheel nuts M6 self-locking
Genuine FG spare/option part.Self locking wheel nuts with serrated base.Part is delivered in silver or black color from vendor!Contents:10 pieces

€7.30*

Average rating of 0 out of 5 stars

7112 Samba O-rings Set 50mm
Genuine Samba spare/option part. Replacement o-ring for Samba pipes.

€9.90*

Similar products

Average rating of 0 out of 5 stars

y6107/01 Wheel squares 18 mm HART-COAT, 14 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€17.45*

Average rating of 0 out of 5 stars

y6107/02 Wheel squares 18 mm HART-COAT, 17 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€18.95*

Average rating of 0 out of 5 stars

6106/07 FG Wheel square 11,5mm - 2pcs.
Wheel squares with 3 mm dowel pins. The pins prevent the squares from damaging the rims under high load. For all FG rims, holes may have to be drilled.11,5mm wide.Bore diameter 8 mm18 mm square

€23.90*

Average rating of 0 out of 5 stars

y0521 Madmax/HPI-rim to FG-car wheel adaptor
y0521 Version: y0521 - for M6 wheel shafts
Genuine HT spare/option part.This adaptor allows you to install all MadMax/HPI tire/rim combinations on FG, Carso, Smartech 2WD/4WD and other cars with the same wheel shaft configuration. Losi 5ive tires can be used as well, but they hey have to be mounted on MadMax/HPI rims because Losi rims are too thick at the center. The adapter is drilled for 8 mm wheel shafts (FG, Smartech/Carson and many more!), hex size of wheel drive and wheel nut is 24 mm hex with M18x1.0 thread (same as HPI).Please note:FG wheel shafts come with either M6 or M8 thread size. It can even happen that a vehicle has different thread sizes front and rear! Therefore, please make sure which version is required before placing an order.Converting your car takes only a couple of minutes with this easy to install adaptor. just see picture "installation instruction" for a schematic installation.Contents:2 pieces

€39.90*

Average rating of 0 out of 5 stars

6107 FG Wheel square 9,5mm/M6
Genuine FG spare/option part. Square wheel driver in high-strength alloy material with M6 fixing thread. Essentially higher retention force. Suitable for all models.Dimensions:Square: 9,5 mm Width: 17 mmBore: 8 mmContent:1 pieces:

€15.90*

Average rating of 0 out of 5 stars

6107/02 FG wheel square 17 mm/M6
Genuine FG spare/option part. Square wheel driver in high-strength alloy material with M6 fixing thread. Essentially higher retention force. Suitable for all models.Dimensions:Square: 18 mm Width: 17 mmBore: 8 mmContents:2 pieces

€16.90*

Average rating of 0 out of 5 stars

TT1051 Top Tuning Conversion kit for the standard 1:/5 18 mm square wheel drives for the Carson CY-Eline cars
Genuine Top Tuning spare/option part. Conversion kit for the standard 1:/5 18 mm square wheel drives for the Carson CY-Eline carsThis allows for the use of all 1/5 on-road wheels e.g. by or . The cars become approx. 5 mm wider per side. This i feasibles with all usual body shells of the CY-E-line cars. Set includes:4 pieces # y6107 hard coated 18 mm aluminum square drives, 9.5 mm wide, with 8 mm axle bore, threaded for 2 x M6 grub screws4 pieces M6 grub screws8 pieces 3x16 mm steel pins4 pieces # 6038 mounting washers 6x15 mm 4 pieces M5x16 mm countersunk screws

€39.90*

Average rating of 0 out of 5 stars

6107/01 FG wheel square 14 mm/M6
Genuine FG spare/option part.Square wheel driver in high-strength alloy material with M6 fixing thread. Essentially higher retention force. Suitable for all models.Dimensions:14 mm wide18mm squareBore diameter 8 mmContent:2 pieces

€16.90*

Average rating of 0 out of 5 stars

y6106/07 Wheel square 11,5mm, steel
Two wheel squares with 3mm dowel pins. Like FG 6106/07, but made from heat treated steel. Significantly reduced wear. The pins prevent the squares from damaging the rims under high load. For all FG rims, holes may have to be drilled. Pins should be fitted using high strength thread locking compound.Measures:18 mm square11.5mm wideBore diameter 8 mm

€19.90*

Average rating of 0 out of 5 stars

y6107/07 Wheel squares 18 mm HART-COAT, 12 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces

€16.45*

Average rating of 0 out of 5 stars

50100000 Lightscale nut spanner for Lightscale Lock wheel nuts, 1 pce.
The special tool for Lightscale wheel nuts is simply inserted into the end of a spark plug wrench and is secured there by use of an o-ring. With its 3 hardened pins the tool locates into the wheel nut and may be used to tighten or untighten it. The tool is universally usable for all Lightscale wheel nuts.The kit contains the tool as well as the o-ring and hardened pins. The tool comes ready for use. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.

€21.50*

Average rating of 0 out of 5 stars

51039600 Lightscale wheel nut, Formel 1 rear M6 (FG Axle), 2 pce.
Wheel nut rear for F1 Cars using M6 Thread on the axle.The Lightscale wheelnut is used in combination with the Lightscale lexan disc to convert F1 rims to an up to date and modern look.Thereby the Lightscale wheel nut works just like a real one in present f1 racing. It is tightened with a 22 open end spanner or socket wrench. Alternatively one may use the special Lightscale toolto tighten or loosen the wheel nut.Due to the use of rifled and conical washers a locking effect is achieved.Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The kit contains two wheel nutsas well as four rifled conical washersOptional parts: Tool for Lightscale wheel nuts (item code two wheel nutsas well as four rifled conical washersOptional parts: Tool for Lightscale wheel nuts (item code 50100000)

€22.50*

Customers also viewed

Average rating of 0 out of 5 stars

HA0080 Hurrax Steel wheel drives 17 mm hex, 19 mm wide
Genuine Hurrax spare/option part.17 mm hex wheel drives, 19 mm wide with 8 mm bore diameterm. Weight 20 grams.Contents:2x Adaptor4x Grub screws M 5x5 mm

€19.90*

Average rating of 0 out of 5 stars

y1589/01 Subaru Impreza Ralley Monte-Carlo 99 Body shell, painted
The body shell is complete painted for 1/5 cars with 510/515 mm wheelbase.With rear wing and decal sets.The body shell does not come with drilled mounting holes to make it possible to fit any 1/5 car with 510/515 mm wheelbase. Dimensions: Length: ca. 900 mm Width: ca. 370 mm Height: ca. 250 mm Required body mounts: Front bumper: 7020/16 and 7011/01 Front side: 8013 Rear side: 3014 Rear mount: 2x 7152/01 and 1x 7153 Contents:1 piece

€299.00*

Average rating of 0 out of 5 stars

Challenge Line 2WD 530E Electric Audi A4 incl. ESC + Motor
Genuine FG spare/option part. The FG Touring and Sports cars at scale 1:5 are known for their high quality and very detailed bodyshells true to original. Also the technically fully developed chassis are worth mentioning. These models are now available with a high-torque brushless engine. Surface conditions with maximum grip assumed speeds above 100 km/h can be reached and steered controlled. E stands for electric power which is equivalent to extremely high torque, high speed and all this without any engine noise. The Challenge Line models are equipped with a powerful 800 - 1300 kV brushless Motor and a 150A brushless ESC. This control can be regulated simply via transmitter or optionally via the program card.The models are built on a 4mm aluminium chassis with rear wheel drive and double wishbones front and rear. All borings are countersunk. Fully adjustable front and rear double wishbone suspensions.Further equipment points are: differential gear, oil-pressure shock absorbers with volume control and external, adjusting ring for the initial tension of the spring. All rotating parts on ball bearings.Tires are glued on the rims.For all versions of the electric cars, the LiPo batteries and the matching charger, as well as the radio system and the steering servo (RTR) are required. In our shop selection, the RTR set is available for a surcharge.For hassle-free assembly, FG recommends using LiPo batteries 2x 2S or 2x 3S, with a maximum dimensions of 150 mm in length and 50 mm in width. The model comes with the EC8 connector system equipped.

From €849.90*

Average rating of 0 out of 5 stars

6183/01 FG Alloy spacer tubes, 8x27 mm/10x34 mm
Genuine FG spare/option part. Necessary for 6183 and 6184.Contents:2 pieces

€7.50*

Average rating of 0 out of 5 stars

9452 FG Hydraulic oil 50 ml
Genuine FG spare/option part. Spare part for 9440 and Hydraulic brakes.Contents:1 piece / 50 ml

Content: 50 Milliliter (€364.00* / 1000 Milliliter)

€18.20*

Average rating of 0 out of 5 stars

y6107/02 Wheel squares 18 mm HART-COAT, 17 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€18.95*

Average rating of 0 out of 5 stars

6079/01 FG Rear axle shaft for ball drive
Genuine FG spare/option part. For ball drive system only!Diameter: 8 mm.Contents:1 piece

€33.90*
Loading...
Upload in progress, please be patient ...
Shopware-Plugin Development Shopware-Agency