LOS252012 Front/Rear Wheel Hex & Pin Losi DBXL 1/5 4WD

€29.99*

Prices incl. VAT plus shipping costs

Available

Product number: losi_los252012

EAN: 6054821180162

Product information "LOS252012 Front/Rear Wheel Hex & Pin Losi DBXL 1/5 4WD"

Genuine Losi spare/option part.

Contents:

2 pieces

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Alternatives

y1345 Drive pins, choice of sizes, e.g. for Losi, Mini and HPI cars

Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces

€4.90*

Details

Similar products

LOS252017 Axle Boot Set Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part. Contents:10 pieces

€29.99*

LOS252009 Differential Rebuild Kit Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part. Contents:1 set

€8.99*

LOS252006 Front/Rear Differential Outdrive Set Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part. Contents:2 pieces

€29.99*

LOS252019 Front Center Driveshaft Losi DBXL 1/5 4WD

Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 piece

€59.99*

LOS252135 Losi Center Driveshaft, rear: DBXL 2.0

Genuine Losi spare/option part. Contents:1 piece

€39.99*

LOS252016 20T Pinion Gear Losi DBXL 1/5 4WD

Genuine Losi spare/option part. Contents:1 piece

€19.99*

LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL

Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

€11.99*