y0441 HT Rim reinforcement for FG 60200 and 60205 rim
Product information "y0441 HT Rim reinforcement for FG 60200 and 60205 rim"
Genuine HT spare/option part.
Rim reinforcement, transfers the load over a larger diameter into the rim and protects the rim's square. Will also allow for the use of rims with an already damaged square.
For FG Off-Road rims 60200, 60201 (wide) and 60205, 60206 (narrow).
14 mm wide square drives must be used.
Please note:
When installed with new (unused) rims, it may be necessary to modify the rim's square slightly.
Contents:
Rim reinforcement, transfers the load over a larger diameter into the rim and protects the rim's square. Will also allow for the use of rims with an already damaged square.
For FG Off-Road rims 60200, 60201 (wide) and 60205, 60206 (narrow).
14 mm wide square drives must be used.
Please note:
When installed with new (unused) rims, it may be necessary to modify the rim's square slightly.
Contents:
- 2 piece
Login
Similar products
Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey and Super Rock Rey.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: The adapters only fit in combination with the standard plastic steering knuckles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which then prevents the drive pin from being fitted.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fender wells will need some cutting.Please note: the wide rear wheels from MadMax or HPI do not fit!This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm
Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey, Super Baja Rey 2.0 and Super Rock Rey. Suitable for 8 mm axles.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: These adapters only fit in combination with the optional aluminum spindles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which requires different dimensions for the wheel drives.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fenderwells will need some cutting.
Please note: the wide rear wheels from MadMax or HPI do not fit!
This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm
Genuine Top Tuning spare/option part. Conversion kit for the standard 1:/5 18 mm square wheel drives for the Carson CY-Eline carsThis allows for the use of all 1/5 on-road wheels e.g. by or . The cars become approx. 5 mm wider per side. This i feasibles with all usual body shells of the CY-E-line cars. Set includes:4 pieces # y6107 hard coated 18 mm aluminum square drives, 9.5 mm wide, with 8 mm axle bore, threaded for 2 x M6 grub screws4 pieces M6 grub screws8 pieces 3x16 mm steel pins4 pieces # 6038 mounting washers 6x15 mm 4 pieces M5x16 mm countersunk screws
y0521 Version:
y0521 - for M6 wheel shafts
Genuine HT spare/option part.This adaptor allows you to install all MadMax/HPI tire/rim combinations on FG, Carso, Smartech 2WD/4WD and other cars with the same wheel shaft configuration. Losi 5ive tires can be used as well, but they hey have to be mounted on MadMax/HPI rims because Losi rims are too thick at the center. The adapter is drilled for 8 mm wheel shafts (FG, Smartech/Carson and many more!), hex size of wheel drive and wheel nut is 24 mm hex with M18x1.0 thread (same as HPI).Please note:FG wheel shafts come with either M6 or M8 thread size. It can even happen that a vehicle has different thread sizes front and rear! Therefore, please make sure which version is required before placing an order.Converting your car takes only a couple of minutes with this easy to install adaptor. just see picture "installation instruction" for a schematic installation.Contents:2 pieces
24 mm hex wheel adapter for installation of most all common large scale rims with corresponding socket (MadMax/Losi/HPI etc.) on Carson Dirt Attack cars. This allows the use of a variety of different tires for better adaptation to the surface. For installation the stock square drive is swapped for the hex version which is secured by an M6 set screw. The rims are then secured with the 24 mm wrench size nuts of the adapter.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004 ATOP Aluminum closed wheel nuts Losi 5ive-T/2.0/B, Mini, DBXL/2.0 and MTXL 22,90 EUR), which are also offered in our shop's option menu! Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of Allen Grub screw2 pieces of shim
Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP RC, increase track width for 25 mm and allow for the use of HPI 5T, Losi 5ive-T, 5ive-B and Mini rims. 5 mm o-rings protect against drive pin loss. Set of four inclusive o-rings, drive pins and closed wheel nuts (wrench size 24 mm!).Contents:1 set
Genuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi 5ive tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.LosiDBXL rims do not fit the X-Maxx (depth of hex is too deep)!Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces
Item N° y1183/02FG rim to HPI model, drive rim adapter, separate for the front, 2 pcs.These adapters are machined from gas nitrited steel and enable you to put standard rims with 18 mm square drive (FG, Carson, Lauterbacher a.s.o.) on the HPI Baja 5B/SS/T. The track width will be substantially increased.For a complete set covering front and rear axle you need part number y1183.This set includes rim adapters with installation hardware for the front axle only.Measures for front:Outer diameter: circa 17,59 mLength: circa 55,10 mm
The special tool for Lightscale wheel nuts is simply inserted into the end of a spark plug wrench and is secured there by use of an o-ring. With its 3 hardened pins the tool locates into the wheel nut and may be used to tighten or untighten it. The tool is universally usable for all Lightscale wheel nuts.The kit contains the tool as well as the o-ring and hardened pins. The tool comes ready for use. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Wheel nut rear for F1 Cars using M6 Thread on the axle.The Lightscale wheelnut is used in combination with the Lightscale lexan disc to convert F1 rims to an up to date and modern look.Thereby the Lightscale wheel nut works just like a real one in present f1 racing. It is tightened with a 22 open end spanner or socket wrench. Alternatively one may use the special Lightscale toolto tighten or loosen the wheel nut.Due to the use of rifled and conical washers a locking effect is achieved.Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The kit contains two wheel nutsas well as four rifled conical washersOptional parts: Tool for Lightscale wheel nuts (item code two wheel nutsas well as four rifled conical washersOptional parts: Tool for Lightscale wheel nuts (item code 50100000)
Hardware set for wheel adapter FG rim to HPI car:y1183y1183/02y1183/03
Wheel nut front for F1 Cars using M8 Thread on the axle.The Lightscale wheelnut is used in combination with the Lightscale lexan disc to convert F1 rims to an up to date and modern look.Thereby the Lightscale wheel nut works just like a real one in present f1 racing. It is tightened with a 22 open end spanner or socket wrench. Alternatively one may use the special Lightscale tool to tighten or loosen the wheel nut.Due to the use of rifled and conical washers a locking effect is achieved.The kit contains 2 wheel nuts as well as 4 rifled conical washers.Optional parts: Tool for Lightscale wheel nuts item code 50100000, Lightscale lexan disc item code 51009500 and spare rifled conical washers item code 881200058801. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Customers also viewed
Genuine HT spare/option part.Rim reinforcement, transfers the load over a larger diameter into the rim and protects the rim's square. Will also allow for the use of rims with an already damaged square.For FG Off-Road rims 6105, 6105/01 (white) and 3105 (silver).14 mm wide square drives must be used.Please note:When installed with new (unused) rims, it may be necessary to modify the rim's square slightly.Contents:2 pieces
Genuine HT spare/option part.Rear alloy damper plate with several adjustment possibilities of the shock absorbers. Replacement for FG plastic rear shock tower FG 7072/01Please note: When installing in combination with plastic diff mounts you should insert a-arms with hinge pins before bolting together rear plate and diff mounts.Content:1 pieces
Diameter: 123 mmWidth: 65 mmDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Rims with 18 mm square drive (fits FG, Harm, RS5, Carson, Smartech a.s.o.).Contents:1 pair (2 pieces)
BUILD YOUR OWN ORIGINAL,AUTHENTIC HPI BAJA 5BHPI large scale fans, we have heard you! The one and only original HPI Baja 5B is BACK and ready for you to build from the ground up! The HPI SBK collection of Self Build Kits grows with the addition of not just one, but TWO 1/5th scale HPI kits! Fans of large scale off-road RC will be super excited to build their own gas-powered 1/5th scale Buggy with the HPI Baja 5B Self Build Kit!When the HPI Baja 5B buggy was first introduced, large scale RC was very expensive and quite difficult for the average RC hobbyist to experience. Using highly durable parts and innovative design features, HPI brought large scale off-road to new enthusiasts and ushered in a new, BIGGER era of RC!Now, YOU can build and own the legend! Experience the thrill and excitement of building a car which ends up being over 80cm (nearly 32 inches) long and weighing nearly 10kg (over 21 lb)! Just install your own engine and electronics as you build the HPI Baja 5B and you'll be ready for any adventure that comes your way!With extra-tough drivetrain parts like the viscous torque differential, super-durable composite spur gear with internal damping and all-metal drivetrain, the HPI Baja 5B is ready for your 23-32cc 2-stroke engine so you can experience the joy of gas-powered RC and up to 30-minute runtimes!The HPI Baja 5B is also equipped with extra-big and super-tough suspension parts, featuring awesome HPI durability! With its expertly designed molded composite suspension plus extra-long adjustable HD shocks, and massive high impact nylon 3-piece beadlock wheels, the Baja 5B is ready for full-speed racing on any off-road circuit!The 4mm thick 6061 aluminum monocoque chassis gives the HPI Baja 5B the classic desert racing buggy look. Precisely bent into shape for maximum strength, the chassis provides the mounting points for the engine and suspension, forming the backbone of the car. Precise steering is provided by a dual-bellcrank rack and cam-type servo saver. Aluminum parts are anodized in cool gunmetal and the classic Baja desert racer clear polycarbonate body is included in the SBK kit, ready for your custom racing scheme!The Baja 5B SBK is a great addition to your HPI collection, as well as a fabulous introduction to large scale buggies!RACING CHASSIS DESIGN & LAYOUTThe narrow channel chassis made from rigid 4mm 6061 aircraft aluminum and gives the HPI Baja 5B a classic desert racing buggy look and extreme stiffness and durability. The U-shaped chassis is protected at the rear with a thick plastic skid plate for extra protection to the motor and drivetrain.The tube roll cage is made of high impact nylon and topped with a real aluminum roof to carry on the classic looks. The roll cage is fully functional and protects the motor and internals from crash damage. The roll cage, radio box, body panels, wing, undertray and gear case are all mounted with fast access clips for easy maintenance. To finish you need: Engine with clutch and exhaust Remote control with servos and receiver battery Charger Two cans of Lexan paint Features Summary Unassembled 1/5th scale electric-powered Off-Road Buggy Ready for your 6S or 8S LiPo electronics Streamlined HPI Baja 5B Flux body design Adjustable motor mount Adjustable HD shock absorbers Monocoque chassis Low CG for superior handling Long travel suspension Viscous torque oil-filled gear differential All-terrain tires Beadlock wheels with metal insert hubs Aluminum rear shock tower Hard plastic skid plates Adjustable rear wing Quick access to all critical maintenance points Dual bellcrank steering Cam type servo saver Hex socket hardware Gunmetal anodizing Full set of rubber-sealed ball bearings Enclosed receiver box Chassis Specifications Overall Length 817mm Height: 255mm Width: Front - 460mm; Rear - 480mm Tire Track (to center of tires): Front - 395mm; Rear - 400mm Wheelbase: 570mm Ride Height: 76mm Suspension Travel: Front - 95mm; Rear - 100mm Weight: 9.6kg (21.3lb) Adjustable Camber: front - shims; rear - screw Front caster: adjustable with shim 22 / 25.5* / 29 degrees (* stock) Toe-in: Front adjustable with tie rod; Rear adjustable with inserts 0-4 degrees (3 degrees stock set-up) Aircraft aluminum 6061 T6 monocoque chassis Double wishbone suspension with adjustable roll center F/R Drive system: HD metal gears with sealed gear box (8.382:1 gear ratio) Differential: viscous torque control with 4 pinion gears; sealed diff case with silicone oil Shock absorber: HD Aluminum coilover shock absorber with fully adjustable preload collar Wheel type: 3-piece beadlock design, high impact nylon material with inset heavy-duty metal hex hub
%
Genuine HT spare/option part. Aluminum engine mount for Losi DBXL with reinforced threads due to separate threaded inserts. The steel inserts are set with thread locking compound and feature a flange on the top side for an absolute secure fit.A much safer seating of the engine and the ability to dissipate heat into the chassis plate are the advantages over the stock plastic engine mount.The original screws can be re-used.Contents:1 piece
1 pair glued to original FG rim (rear tyre with outer widening), incl. foam rubber insert,
FG rim with 18 mm square mount and reinforcement ring. As good as new!
New price 74,90 € -Diameter 153 mm -width 78 mm See photos for condition.
