Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

Genuine FG spare/option part.For all FG cars with standard drive shafts (no ball drive). Accepts dogbones with 10 mm ball and 4 mm pin.Dimensions:Shaft, diameter: 8 mmLength: 27 mmSpline drive for FG bevel gearsCup, diameter: 18,5 mmLength 14 mmContents:1 piece

Genuine FG spare/option part.Dimensions:Diameter: 7,10 mmTotal length: 107,5 mmContents:1 piece

Genuine FG spare/option part. Replacement drive shaft (dogbone). Long Version.Suitable for BMW GTR, Mercedes CLK-GTR, Race-Trucks, C291, Porsche GT1, GT2, GT3 and all FG Off-Road models.Dimensions:Shaft diameter: 7 mmBall diameter: 10 mmLength: 101,5 mmContents:1 piece

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt.For FG and Carson ball drives, fits standard dogbones as well.Content10 pieces

Replacement balls for ball driveshaft.

Fits all FG cars and the Mecatech FW01. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins. The GPM ball drives can be partially mixed with FG parts. The heads of the GPM driveshafts fit into FG differential cups or wheel shafts.The opposite combination, i.e. FG shafts in GPM differential cups or wheel shafts does not always fit. We had tests where some FG shafts fit neatly, but due to slight tolerances others who did not fit into the very same cups/shafts. For this combination, we can not guarantee compatibility! Dimensions: Diameter: 8 mmTotal length 76.6 mm

Genuine FG spare/option part. Please note: If you own a Leopard 2WD with the old 130.5 mm driveshafts (same part number), the upgrade of both shafts is recommended.Contents:1 piece

Genuine HT spare/option part. Dimensions:Total length: approx. 132 mmLength center pin / center pin: approx. 123 mmShaft diameter: approx. 6 mmBall diameter: approx. 9,8 mmPlease note:If you own a Leopard 2WD with the old 130.5 mm driveshafts, the swap of both shafts is recommended.Contents:1 piece

FG Set price: 130,20 EURFits all FG touring cars, GT-models and Mecatech FW01.The ball drive conversion kit for FG marder, Off-Road Buggy, beetle, monster / stadium, formula 1 and truck models you will find under GPM 9472. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM ball drive set includes everything for a conversion of the respective FG/Mecatech cars. Set includes:Quantity:DescriptionPart number2 piecesBall drive wheel shaftGPM 6079/012 piecesDifferential ball drive cupGPM 6069/022 piecesBall drive shaft 91 mmGPM 7081/014 piecesDrive shaft booty100412 piecesSteel ballGPM 7080/024 piecesDrive shaft spacer springy1218

Fits all FG offroad / monster and stadium models (except Leopard 2010 up). Also for FG Formula 1 and Race Truck models. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins. The GPM ball drives can be partially mixed with FG parts. The heads of the GPM driveshafts fit into FG differential cups or wheel shafts.The opposite combination, i.e. FG shafts in GPM differential cups or wheel shafts does not always fit. We had tests where some FG shafts fit neatly, but due to slight tolerances others who did not fit into the very same cups/shafts. For this combination, we can not guarantee compatibility! Dimensions: Length 96.5 mm

Item N° 9473Ball drive set for Leopard Sportsline, setFits for 2WD/4WD Sportsline.Not suitable for front application on 4WD cars!

Fits all FG 4WD cars (except FG Leopard!) Lost drive shafts are a thing of the past! Universal drive shafts allow for higher drive angles than dog bones or ball drives. This makes them a better choice for for wheel-side applications on front axles, where the angles of the steering and suspension meet.GPM universals for ball drive can be disassembled and therefore repaired or rebuilded if necessary. The center pin (No.: < href="https://rc-car-online.de/en/products/gpm_66275_02-gpm-66275-02.html">66275/02) of the GPM universal joint is secured by a grub screw, which should be installed using a medium strength screw locking compound (66275/02).Therefore the joint can be easily rebuilded by replacing the center pin for cheap and will be good as new again.The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.

Genuine FG spare/option part. Diameter 8 mm.Contents:1 pieceFor older 2WD models that are not based on the 4WD models, please refer to Sportsline 2008. or if an RC plate is no longer fitted, check Sportsline 13 in Parts Scout.There you will find the right spare parts for your vehicle.

Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces

Genuine FG spare/option part. Standard driveshaft, short version.Fits FG Audi, BMW 320, Peugeot 307, Renault Megane und VW New Beetle.Dimensions:Shaft diameter: 7 mmBall diameter: 10 mmLength: 90 mmContents:1 piece

Genuine FG spare/option part.Spare part for Sportsline Leopard 4WD.Contents:1 piece

Solid universal joints made of hardened, high-quality steel for the front axle of Leopard 4 RTR. With ball drive and ball diff. axle. The model has a higher steering deflection and a smoother driving performance in curves if you mount this universal joint.

Fits all FG and Mecatech touring cars and gt-models. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins. The GPM ball drives can be partially mixed with FG parts. The heads of the GPM driveshafts fit into FG differential cups or wheel shafts.The opposite combination, i.e. FG shafts in GPM differential cups or wheel shafts does not always fit. We had tests where some FG shafts fit neatly, but due to slight tolerances others who did not fit into the very same cups/shafts. For this combination, we can not guarantee compatibility! Dimensions: Length 91 mm

Genuine FG spare/option part.Standard driveshaft, medium length. Fits BMW M3 GTR, Mercedes C-Klasse DTM 04, Mercedes CLK-DTM, McLaren GT, Honda Accord, Dogde Viper, Opel V8 und Porsche Carrera GT.Dimensions:Shaft diameter: 7 mmBall diameter: 10 mmLength: 96 mmContents:1 piece

Genuine GPM spare/option part. Set of four axle pins and M3 x 8 mm grub screws. With 3 mm wide x 0.4 mm deep flat section.Dimensions:Diameter: approx. 2,97 mmLength: approx. 16,85 mmContents:1 set

Item N° 67277 Ball driving shaft rear 130,5mm Leopard 2WD, 1pce.Spare part for the Leopard 2WD 2010 version

Fits all FG offroad (like Marder, Off-Road Buggy, Beetle) / monster and stadium models (except Leopard 2010 up). Also for FG Formula 1 and Race Truck models.The ball drive conversion kit for FG touring cars and gt-models you will find here: GPM 9471. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM ball drive set includes everything for a conversion of the respective FG car. Set includes:Quantity:DescriptionPart number2 piecesBall drive wheel shaftGPM 6079/012 piecesDifferential ball drive cupGPM 6069/022 piecesBall drive shaft 96,5 mmGPM 6080/014 piecesDrive shaft booty100412 piecesSteel ballGPM 7080/024 piecesDrive shaft spacer springy1218