Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

9473 FG Ball drive set for Leopard 2WD/4WD Sportsline, set

Product information "9473 FG Ball drive set for Leopard 2WD/4WD Sportsline, set"

Item N° 9473
Ball drive set for Leopard Sportsline, set



Fits for 2WD/4WD Sportsline.
Not suitable for front application on 4WD cars!

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Accessories / Spare parts

Average rating of 0 out of 5 stars

y1218 Springs for drive shafts
Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

€4.90*

Average rating of 0 out of 5 stars

7080/02 FG Balls for ball driveshaft, 5 mm
Genuine FG spare/option part.Replacement balls for ball driveshaft.Contents:six pieces

€4.90*

Average rating of 0 out of 5 stars

7080/03 FG Distance disk - 4pcs.
Rubber pad, fits inside of ball drive cups.Diameter 10.7 mmThickness 1.6 mm

€3.60*

Average rating of 0 out of 5 stars

7080/04 FG Balance spring tapered, 4 pcs.
Item N° 7080/04Balance spring tapered, 4 pcs.

€5.90*

Customers also bought

Average rating of 0 out of 5 stars

5705 Mielke Big Tornado tuned pipe
Genuine Mielke spare/option part. Even better uniform power over the whole speed range. Especially in the major driving areas from 10.000 rev / min. to full speed. With 560 grams ideal weight for balanced driveability. Center of mass as low as possible new construction. Only 0,8 mm of specially thin steel metal.Compared to its predecessor the tube's diameter increased for about 10 mm. which allows for the better performance. The new set also comes with teflon seal # 5702.Including manifold and mounting material.Suitable for: 1:5 on road 2WD FG Sportsline, Evo- and Competition cars Mecatech FW01 S88R Harm SX4, SX5 Genius Contents:1 piece

€249.00*

Average rating of 0 out of 5 stars

67360 FG Conversion kit for gear brake Leopard
Genuine FG spare/option part. The gear set is needed to convert the Leopard 2 and Leopard 4 Competition with 4 disk brakes to the lighter gear brake. According to the loss of brake and servo parts we achieved a weight reduction of approx. 350 grams.Content:1 set

€259.95*

Average rating of 0 out of 5 stars

Receiver switch, universal connectors, F1408 - 1pce.
Futaba / universal type connectors for both battery and receiver.

€9.90*

Average rating of 0 out of 5 stars

y0695 HT Tool bag
Tools and decorative items are for presentation purpose only and not included. Genuine HT spare/option part. Tool bag, extremely rugged tool bag made from reinforced fabric, sewn edge. With 41 flexible attachment loops for various tools with all-round zipper and reinforced handle.Dimensions:Width: 510 mm Height: 275 mmContents:1 piece

€22.90*

Similar products

Average rating of 0 out of 5 stars

y1218 Springs for drive shafts
Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

€4.90*

Average rating of 0 out of 5 stars

y1004 Driveshaft boots for ball drive + dogbones
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

Average rating of 0 out of 5 stars

y6107/02 Wheel squares 18 mm HART-COAT, 17 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€18.95*

Average rating of 0 out of 5 stars

y0897 Wheelie bar with suspension for 2WD + 4WD models - 1pce.
Wheelie bar with double ball raced wheel, cnc-machined from high strength alloy. The arm has a rubber suspension unit, the height is infinitely adjustable. The suspension allows for a maximum deflection of 30 degrees and is dirt- and mud-proof. The wheel bearings are sealed.The unit fits FG Monster Truck, Monster Beetle and Marder BigFoot, except for Monster Buggy Off-Road WB535 4WD. Installation on other models will be possible, but requires modifications to the chassis, mainly to accept the bolt pattern. The Carson Attack already has the correct pattern.

€89.90*

Average rating of 0 out of 5 stars

y6107 Wheel squares 18 mm HART-COAT, 9,5 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€14.95*

Average rating of 0 out of 5 stars

y6107/01 Wheel squares 18 mm HART-COAT, 14 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€17.45*

Average rating of 0 out of 5 stars

7497/01 FG Rear brake 2WD/4WD
Genuine FG spare/option part. The set will shipped without gear carrier plate. Contents:1 set

€55.90*

Average rating of 0 out of 5 stars

y6479 HT rear alloy upright
Genuine HT spare/option part.Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.Comes with adjustment clips and grub screws for the hinge pins included.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm Contents:2 pieces

€89.90*

Average rating of 0 out of 5 stars

y6107/07 Wheel squares 18 mm HART-COAT, 12 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces

€16.45*

Average rating of 0 out of 5 stars

y1072 HT Alloy differential spur gear protector
Genuine HT spare/option part.Gear protector for the bottom of the 2WD chassis plate. Replaces stock plastic part FG 6082 or Carson 32481.Contents:1 piece

€29.90*

Average rating of 0 out of 5 stars

y04475 HT Rear alloy shock mount 2WD
Genuine HT spare/option part.Rear alloy damper plate with several adjustment possibilities of the shock absorbers. Replacement for FG plastic rear shock tower FG 7072/01Please note: When installing in combination with plastic diff mounts you should insert a-arms with hinge pins before bolting together rear plate and diff mounts.Content:1 pieces

€89.90*

Average rating of 0 out of 5 stars

y04476/02 HT Alloy rear diff mount l/h+r/h one-piece-solid
Genuine HT spare/option part. Suitable for all FG 2WD and Smartech/Carson 2WD models except Evo 04/Competition 07/EVO 07 and Formula 1. Content:2 piece

€99.90*

Customers also viewed

Average rating of 0 out of 5 stars

GPM 9471 Ball drive conversion kit for FG and Mecatech touring cars and gt-models
FG Set price: 130,20 EURFits all FG touring cars, GT-models and Mecatech FW01.The ball drive conversion kit for FG marder, Off-Road Buggy, beetle, monster / stadium, formula 1 and truck models you will find under GPM 9472. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM ball drive set includes everything for a conversion of the respective FG/Mecatech cars. Set includes:Quantity:DescriptionPart number2 piecesBall drive wheel shaftGPM 6079/012 piecesDifferential ball drive cupGPM 6069/022 piecesBall drive shaft 91 mmGPM 7081/014 piecesDrive shaft booty100412 piecesSteel ballGPM 7080/024 piecesDrive shaft spacer springy1218

€149.90*

Average rating of 0 out of 5 stars

60209/05, FG Tire Off-Road Buggy S wide glued
Genuine FG spare/option part. 1:/6 Off-Road Buggy tires, medium, glued on FG Off-Road buggy-rim white. Outer Ø 175 mm, width 80 mm, Suitable for the FG cars Marder, Off-Road Buggy, Beetle and Monster cars with 18 mm square wheel drive. Suitable for other 1/6 cars as well: please check the wheel drive regarding this matter. When the wheel change causes a significant change of the tire's outer diameter, adapting the gear ratio is recommended.Contents:2 pieces

€107.95*

Average rating of 0 out of 5 stars

9472 FG Ball driving set for GT1, F1, Buggy and Trucks
Genuine FG spare/option part.Suitable for the FG GT1 models with a width of 420mm, f.e. CLK-GTR, Porsche GT1, GT2, GT3, for the Formula 1 and all 1:6 Buggy and Monster models. For rear axle only! 4WD cars must use GPM ball drive set GPM66275 for the front.For Marder and Beetle models until Nov'03 the raised uprights 6077 bzw. 6478 are needed.Content:1 set

€138.50*

Average rating of 0 out of 5 stars

y0897 Wheelie bar with suspension for 2WD + 4WD models - 1pce.
Wheelie bar with double ball raced wheel, cnc-machined from high strength alloy. The arm has a rubber suspension unit, the height is infinitely adjustable. The suspension allows for a maximum deflection of 30 degrees and is dirt- and mud-proof. The wheel bearings are sealed.The unit fits FG Monster Truck, Monster Beetle and Marder BigFoot, except for Monster Buggy Off-Road WB535 4WD. Installation on other models will be possible, but requires modifications to the chassis, mainly to accept the bolt pattern. The Carson Attack already has the correct pattern.

€89.90*

Average rating of 0 out of 5 stars

4412 FG Driveshaft boots
Genuine FG spare/option part. Suitable for all FG models and other. To complete one car you need two sets.For 2WD models you need two sets and for 4WD models you need four sets.Contents:2 pieces

€19.90*

Average rating of 0 out of 5 stars

67210/05 FG Mini Pin M / OR tires, Leo wheel white, glued, 2pcs.
Item N° 67210/05 Mini Pin M / OR tires, Leo wheel white, glued, 2pcs. Completely new revised and in important details improved Mini Pin Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant. The FG Mini Pin tires are especially well-suited for hard and rough ground. They give the model a lot of traction, driving stability and grip in curves. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle.The tires are ready glued on the new Leo wheels. For the assembly you need the 12mm square wheel drivers (Item-no.: FG 6107/07). The glued tires are not suitable for the FG models Marder, Beetle, Off-Road Buggy and Monster models. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.

€54.90*

Average rating of 0 out of 5 stars

6080 FG Rear dogbone
Genuine FG spare/option part. Replacement drive shaft (dogbone). Long Version.Suitable for BMW GTR, Mercedes CLK-GTR, Race-Trucks, C291, Porsche GT1, GT2, GT3 and all FG Off-Road models.Dimensions:Shaft diameter: 7 mmBall diameter: 10 mmLength: 101,5 mmContents:1 piece

€19.00*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Theme Development