y1004/01 Driveshaft boots for ball drive and dogbones
€34.90
Available
Product information "y1004/01 Driveshaft boots for ball drive and dogbones"
Protect ball drive as well as cardan drive against dirt.
For FG and Carson ball drives, fits standard dogbones as well.
Content
- 10 pieces
Nauenweg 55
47805 Krefeld
Germany
Login
Accessories / Spare parts
For the secure installation of driveshaft boots.
Customers also bought
Genuine FG spare/option part. Dimensions:Length: 33 mmWire diameter 1.5 mmContents:10 pieces
Single spare parts to replacement number: y0460Ceramic ball bearings suitable for the aluminum and plastic shaft bearings of the clamping roller in the back tension roller housing for all 4WD models FGDimensions: 10 x 19 x 7 mm
Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5cm³ cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.
Item N° 6432 Steel pinion 18 teeth - 1pce.For combination with 46T main spur gear.Diameter 29,7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5
Customers also viewed
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces
This pair of Tyres have the following use indications: GOOD GRIP situation for clean track. GOOD GRIP situation for medium asphalt. GOOD GRIP situation for medium temperatures. This pair of Tyres have the following technical features: REVO treated profile for the maximum traction and the maximum lateral grip. Treated profile studied to maintain the tyre surface alway clean from rubber murble. Compound exclusively developped for model tyres. Inside belt flexible but very strong, vulcanized directly together with tyre compound. Insert foam with special material for high temperatures, for maximum stability and high drive precision. Spoked wheel moulded with special material for high temperatures for maximum grip and stability. Special gluing system 100% guaranteed.The main sizes for this tyre are: WHEEL fixing with square 18mm. TYRE outside diameter 118mm. WHEEL inside diameter 90mm. TYRE tota width 65mm. Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!
FG Set price: 130,20 EURFits all FG touring cars, GT-models and Mecatech FW01.The ball drive conversion kit for FG marder, Off-Road Buggy, beetle, monster / stadium, formula 1 and truck models you will find under GPM 9472. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM ball drive set includes everything for a conversion of the respective FG/Mecatech cars. Set includes:Quantity:DescriptionPart number2 piecesBall drive wheel shaftGPM 6079/012 piecesDifferential ball drive cupGPM 6069/022 piecesBall drive shaft 91 mmGPM 7081/014 piecesDrive shaft booty100412 piecesSteel ballGPM 7080/024 piecesDrive shaft spacer springy1218
Genuine FG spare/option part.For all FG cars with standard drive shafts (no ball drive). Accepts dogbones with 10 mm ball and 4 mm pin.Dimensions:Shaft, diameter: 8 mmLength: 27 mmSpline drive for FG bevel gearsCup, diameter: 18,5 mmLength 14 mmContents:1 piece
Genuine FG spare/option part. The gear set is needed to convert the Leopard 2 and Leopard 4 Competition with 4 disk brakes to the lighter gear brake. According to the loss of brake and servo parts we achieved a weight reduction of approx. 350 grams.Content:1 set
Genuine FG spare/option part. Up to version 2004.Contents:1 piece
Genuine spare/option part.Suitable for the new FG Off-Road Buggy and Leopard tires. Fits 18 mm square wheel drives.Dimensions:Inner diameter: approx. 125 mmouter diameter: approx. 139 mmInner diameter of glueing slot: approx. 130 mmWidth: approx. 65 mmContents:2 pieces