Clutch parts / accessories

y19302/01 Flywheel and Clutch puller CY, Zenoah, HPI, Losi

Genuine HT spare/option part. Especially for CY / Zenoah G230/240/260/270/290/320, HPI and Losi engines.Can be used for removal of the standard clutch as well!Contents:1 piece

€29.90

7316/09, FG OEM clutch complete, set for Zenoah/CY/Fuelie/Losi engines

Complete clutch with spring, carrier and bolts. For Zenoah G230/240/260/270/290/320 und CY / Fuelie / Losi engines.

€22.45 €44.90 (50% saved)

7317/11 FG Clutch spring reinforced 2,7mm G230/260/240/270/290/320

Genuine FG spare/option part. Fits Zenoah G230/260/240/270/290/320.Reinforced clutch spring for the Zenoah standard clutch. Engagement speed approx. 8000rpm. The engine has a higher torque and therefore more power for acceleration according to the raised operative speed. Suitable for all Zenoah engines.Contents:1 piece

€9.90

y1419 Sintered steel clutch for Zenoah and many other engines from 23 cm³ to 32 cm³, incl. clutch spring

Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³. incl. clutch spring!Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!

€29.90

y1419/01 Clutch spring 6.000 1 / min for the Sintered clutch for Zenoah, Chung Yang, Losi, HPI & Co.

Clutch spring for about 6,000 1 / min. for the OEM clutches from Zenoah and many other rc-car engines from 23 cm³ - 32 cm³.Content:1 piece

€4.90 €5.90 (16.95% saved)

7316 FG Clutch blocks for Zenoah

Genuine FG spare/option part. Zenoah bolts 7318 are required for installation.Content:2 pieces

€27.90

Pink-Racing Reinforced clutch spring y0134, 1 pce.

Reinforced spring for Zenoah OEM clutch with 2.7 mm wire diameter and five coils. Engagement speed is around 7500 rpm, which allows the engine to build up more power and torque for accelleration.Fits Zenoah, CY and most other engines in the 23 - 30 cc range with stock clutch.

€4.95

7318 FG Dowel screw set for clutch blocks Zenoah

Genuine FG spare/option part. Part is delivered in silver or black color from vendor!Content:2 pieces

€9.90

Mielke 5445 Power Gearshift clutch adjustement tool

Adjustment tool for Mielke Power Gearshift clutches #5440 and #5441.

€19.90

7317/08 FG Clutch spring for CY / Zenoah

Genuine FG spare/option part.Contents:1 piece

€5.90

AT-DBXL013 ATOP Clutch bell carrier for Losi Desert XL+MTXL

Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum clutch bell holder for Losi DBXL+MTXL. Compared to the stock plastic part the higher strength of the aluminum part ensures secure seat for the bearings, increased dimensional stability at high temperatures and reduced operating temperatures for the bearings due the aluminums thermal conductivity. Larger bearings (12 x 28 x 7) for higher load capacity. Comes with ball bearings and spacer tubes included.It is recommended to use the ball bearings/bushings adhesive (y0113 Thread locking compound).Contents:1 set

€34.90

y0743 Clutch-Safe 10 g, adhesive especially for clutch pads

Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!) Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!) The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended. For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.Attention:Clutch-Safe adhesive must be stored in the fridge! Content: 10g tube

Content: 10 Gramm (€495.00 / 1000 Gramm)

€4.95

5445/1 Mielke tool for clamping of all Power-Gearshift clutches

Genuine Mielke spare/option part. For easier change of springs or clutch shoes.Contents:1 piece

€39.90

5647 Mielke Springs 2,4 mm made from special steel for Converse left

Genuine Mielke spare/option part. Contents:3 pieces

€9.90

5446/01 Mielke Clutch shoes aluminum for Power Gearshift clutches, set of 3

Genuine Mielke spare/option part.Clutch shoes for Mielke Power Gearshift clutches part numbers 5440, 5441 and 5442.Content:3 Pieces

€44.90

5646 Mielke Mix clutch pads single for Power Gearshift Converse II clutch

Genuine Mielke spare/option part.Contents:3 pieces

€44.90

y0730/10 Adjustment screw M5 x 8 mm

Genuine GPM spare/option part. Part no. 10 for GPM Big-Scale clutch.y0730y0731Content:2 pieces

€1.90

Mielke 5648 Springs 2,5 mm made from special steel (blue)

Genuine Mielke spare/option part. Replacement part for Mielke Power Gearshift 2 clutches.Contents:3 pieces

€9.90

Mielke 5447/03 Springs 2 mm made from special steel

Genuine Mielke spare/option part. Replacement part for Mielke Power Gearshift clutches #5440 and #5441.Content:3 pieces

€9.90

7315/05 FG Tuning carrier f. clutch blocks/Zenoah, 1pce.

Item N° 07315/05 Tuning carrier f. clutch blocks/Zenoah, 1pce.Carrier for standard clutch blocks and Tuning clutch blocks made of high-strength aluminium. With cross hole for disassembly of clutch blocks and carrier.

€32.30