y1419 Sintered steel clutch for Zenoah and many other engines from 23 cm³ to 32 cm³, incl. clutch spring

Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.Content:5315 Clutch block carrier5315/01 Screw for carrier7318 Dowel screw for clutch blocksy1419 Sinter clutchy1419/01 Clutch springs for Sinter clutch

Genuine FG spare/option part. Zenoah bolts 7318 are required for installation.Content:2 pieces

Complete clutch with spring, carrier and bolts. For Zenoah G230/240/260/270/290/320 und CY / Fuelie / Losi engines.

Hardened steel pinion set for Losi 5ive-T, 5ive-B and Mini, with corresponding engine mount inserts included. All parts with laser etched tooth count.Please note: The pinion do fit the 5ive-T 2.0 as well, of course. However, you then have to use the 5ive-T 2.0 engine mount inserts of the appropriate tooth count, inserts from the 5ive-T do not fit! Available with 16, 18T/20T/21T. The 19T pinion is stock equipment in Losi 5ive-T and Mini, 20T is stock in the 5ive-B.The 16T pinion is profile shifted and has the same dimensions as a normal 18T pinion.It is specially made for vehicles where the stock tires are replaced by much larger diameter rubber (i.e. monster truck tires and MadMax Giant Grip).Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter.SLO5T018T replaces LOSB5046 and LOSB5805SLO5T019T replaces LOSB5044 and LOSB5801SLO5T020T replaces LOSB5045 and LOSB5802The higher the tooth count, the higher the top speed!

Different versions to choose:y0723 Gas-nitrited tuning clutch bell for FG, Smartech / Carson, Harm, RS5 & Co..Gas-nitrited tuning clutch bell; machined from high grade steel with vents for cooling of the clutch system and holes for easy clutch adjustment. The clutch bell features a significantly reinforced wearing surface which guarantees dimensional stability even under high loads!For best mounting of the pinion the clutch bell shaft has to flats with a 90° offset. As an additional safety device a M5 bolt with washer (included) replaces the E-clip found on stock clutch bells.Suitable for many 1/5 and 1/6 cars, such as all FG (except Formula 1), Carson a.s.o.y0726 Gas-nitrited tuning clutch bell for Losi 5ive-T (unfortunately not available at the moment Alternatively original Losi clutch bell # LOSB5038) )  Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface and face which guarantees dimensional stability even under high loads! The shaft is a tiny bit longer than stock (about 0.2 mm) to prevent the bearings from binding.Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Scale-Cross clutch.Suitable for genuine slot drive Losi pinions. Comes with bolts and spring washers included.y0726/01 Gas-nitrited tuning clutch bell for Losi DBXLGas-nitrited tuning clutch bell with black oxide coating, machined from high grade. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well. This clutch bell is dimensionally identical to the stock part. Heat treatment and the use of a high grade material guarantee long service life.Due to a special heat treatment the clutch bell surface is shaded; this does not effect the function, but ensures great durability.y0729 Gas-nitrited tuning clutch bell for HPI Baja models, 1 pce.Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface whichguarantees dimensional stability even under high loads!Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Scale-Cross clutch.Suitable for slot drive HPI Baja pinions, both stock using a 4mm bolt and aftermarket ones for 5mm bolts. Comes with M4 and M5 bolts included.

Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece