y19302/01 Flywheel and Clutch puller CY, Zenoah, HPI, Losi
Genuine HT spare/option part. Especially for CY / Zenoah G230/240/260/270/290/320, HPI and Losi engines.Can be used for removal of the standard clutch as well!Contents:1 piece
7316/09, FG OEM clutch complete, set for Zenoah/CY/Fuelie/Losi engines
Complete clutch with spring, carrier and bolts. For Zenoah G230/240/260/270/290/320 und CY / Fuelie / Losi engines.
7317/11 FG Clutch spring reinforced 2,7mm G230/260/240/270/290/320
Genuine FG spare/option part. Fits Zenoah G230/260/240/270/290/320.Reinforced clutch spring for the Zenoah standard clutch. Engagement speed approx. 8000rpm. The engine has a higher torque and therefore more power for acceleration according to the raised operative speed. Suitable for all Zenoah engines.Contents:1 piece
y1419 Sintered steel clutch for Zenoah and many other engines from 23 cm³ to 32 cm³, incl. clutch spring
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³. incl. clutch spring!Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!
y1419/01 Clutch spring 6.000 1 / min for the Sintered clutch for Zenoah, Chung Yang, Losi, HPI & Co.
Clutch spring for about 6,000 1 / min. for the OEM clutches from Zenoah and many other rc-car engines from 23 cm³ - 32 cm³.Content:1 piece
7316 FG Clutch blocks for Zenoah
Genuine FG spare/option part. Zenoah bolts 7318 are required for installation.Content:2 pieces
Pink-Racing Reinforced clutch spring y0134, 1 pce.
Reinforced spring for Zenoah OEM clutch with 2.7 mm wire diameter and five coils. Engagement speed is around 7500 rpm, which allows the engine to build up more power and torque for accelleration.Fits Zenoah, CY and most other engines in the 23 - 30 cc range with stock clutch.
7318 FG Dowel screw set for clutch blocks Zenoah
Genuine FG spare/option part. Part is delivered in silver or black color from vendor!Content:2 pieces
Mielke 5445 Power Gearshift clutch adjustement tool
Adjustment tool for Mielke Power Gearshift clutches #5440 and #5441.
7317/08 FG Clutch spring for CY / Zenoah
Genuine FG spare/option part.Contents:1 piece
AT-DBXL013 ATOP Clutch bell carrier for Losi Desert XL+MTXL
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum clutch bell holder for Losi DBXL+MTXL. Compared to the stock plastic part the higher strength of the aluminum part ensures secure seat for the bearings, increased dimensional stability at high temperatures and reduced operating temperatures for the bearings due the aluminums thermal conductivity. Larger bearings (12 x 28 x 7) for higher load capacity. Comes with ball bearings and spacer tubes included.It is recommended to use the ball bearings/bushings adhesive (y0113 Thread locking compound).Contents:1 set
y0743 Clutch-Safe 10 g, adhesive especially for clutch pads
Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!) Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!) The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended. For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.Attention:Clutch-Safe adhesive must be stored in the fridge! Content: 10g tube
Content: 10 Gramm (€495.00 / 1000 Gramm)
5445/1 Mielke tool for clamping of all Power-Gearshift clutches
Genuine Mielke spare/option part. For easier change of springs or clutch shoes.Contents:1 piece
y1419/02 Sintered steel clutch complete set for Losi 5ive-T/2.0, Mini and Desert Buggy
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.Content:5315 Clutch block carrier5315/01 Screw for carrier7318 Dowel screw for clutch blocksy1419 Sinter clutchy1419/01 Clutch springs for Sinter clutch
y0729 Gas-nitrited tuning clutch bell for HPI Baja, Carson Wild GP Attack models, 1 pce.
Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface whichguarantees dimensional stability even under high loads!Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM clutches Big Scale Extreme and Cross.Suitable for slot drive HPI Baja pinions, both stock using a 4mm bolt and aftermarket ones for 5mm bolts. Comes with M4 and M5 bolts included.
5647 Mielke Springs 2,4 mm made from special steel for Converse left
Genuine Mielke spare/option part. Contents:3 pieces
5446/01 Mielke Clutch shoes aluminum for Power Gearshift clutches, set of 3
Genuine Mielke spare/option part.Clutch shoes for Mielke Power Gearshift clutches part numbers 5440, 5441 and 5442.Content:3 Pieces
y0723 Gas-nitrited tuning clutch bell for FG, Smartech/Carson, Harm, RS5 & Co.
Genuine HT spare/option part. Gas-nitrited tuning clutch bell; machined from high grade steel with vents for cooling of the clutch system and holes for easy clutch adjustment. The clutch bell features a significantly reinforced wearing surface which guarantees dimensional stability even under high loads!For best mounting of the pinion the clutch bell shaft has to flats with a 90° offset. As an additional safety device a M5 bolt with washer (included) replaces the E-clip found on stock clutch bells.Suitable for many 1/5 and 1/6 cars, such as all FG (except Formula 1), Carson a.s.o.Contents:1 piece
5646 Mielke Mix clutch pads single for Power Gearshift Converse II clutch
Genuine Mielke spare/option part.Contents:3 pieces
y0730/10 Adjustment screw M5 x 8 mm
Genuine GPM spare/option part. Part no. 10 for GPM Big-Scale clutch.y0730y0731Content:2 pieces
67350 FG Tuning clutch / Zenoah, set
Item N° 67350 Tuning clutch / Zenoah, setComplete clutch with Tuning carrier, lighter clutch blocks, coated dowel screws and reinforced clutch spring. According to the lighter weight the engine speed is slightly higher when the clutch comes, therefore the engine has more power speeding up.
7315 FG Clutch block carrier Zenoah
Genuine FG spare/option part. Content:1 piece
Mielke 5648 Springs 2,5 mm made from special steel (blue)
Genuine Mielke spare/option part. Replacement part for Mielke Power Gearshift 2 clutches.Contents:3 pieces
Mielke 5447/03 Springs 2 mm made from special steel
Genuine Mielke spare/option part. Replacement part for Mielke Power Gearshift clutches #5440 and #5441.Content:3 pieces