TLR252007/5044 On-road gear set for Losi 5ive-T 1.0

€119.90*

Available

Product number: tlr_tlr252007_5044

EAN: 4058575144793

Product information "TLR252007/5044 On-road gear set for Losi 5ive-T 1.0"

On-road gear set for Losi 5ive-T 1.0 for a much higher top speed.

Almost 30% higher than the original gearing!

Does not fit 5ive-T 2.0 version!

Set contains:
- 54T steel spur gear
- 23T clutch bell pinion

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

y1426 HT aluminum gear carrier -on-road- with steel spur gear for the layshaft

Fits FG and Smartech touring cars. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions. The following measures are required for installation of the HT-steel gear adapter "on-road" on the layshaft in FG EVO 2020 cars:- The installed wide 16T layshaft pinion 6431/01 must be replaced by the narrow version 6431.- The supplied 1mm shim must be added between layshaft pinion and ball bearing.- The flat sections on the layshaft do not have the usual 180° offset for the adapter; therefore only one grub screw will be used. However, since this is a wide face M8 version, this is no disadvantage.

€69.90*

Configure now

y0692 HT-Gearset for layshaft and differential fine pitch for 1/5 onroad

Genuine HT spare/option part.Fine pitch gears for layshaft and differential, for competition use in touring car and GT models only. The gears run smoother and quieter than the stock parts, reducing the car's rolling resistance.Module: m=1Fits FG and Smartech / Carson cars. Only for use as a set, not in combination with standard pitch gears!Contents:2 pieces

€79.90*

y0191 HT-Steel spur gear 46 teeth

Fits the y0190/46 HT-Alloy carrier with steel spur gear 46T for the layshaftInner diameter and bolt pattern are the same as a standard FG differential spur gear.Module: m=1,5Content:1 piece

€49.90*

6493 FG Steel spur gear 48T with adapter

Genuine FG spare/option part. Hardened steel gearwheels for the gears of the 1/6 off-road models.Module: m=1,5Contents:1 set

€93.50*

Details

6048 FG Steel gearwheel big 48 teeth

Genuine FG spare/option part. Differential spur gear for all FG street cars except Formula 1. Can also be used as a main spur gear on the layshaft on monster models when mounted on alloy gear carrier y0190.Dimensions:Outer diameter: 75 mmWidth: 7.5 mmBore: 45 mmModule: m=1,5Contents:1 piece

€52.90*

32452 Gear 1 - 1pce.

cs_32452 Quality: nitrided+ 8.7EUR

Differential spur gear 48T for Carson / Smartech 2WD cars.Module: m=1,5

Variants from €44.90*

€53.60*

y0119 Steel pinion 16 teeth

Steel pinion 16 teeth suitable for 46 mm main gear for FG models.Modul 1,5

€29.90*

6492 FG Steel spur gear 46T with adapter - set

Hardened steel spur gear for FG 1/6 off-road models, spur gear diameter 72 mm.Module: m=1,5

€97.90*

Details

y0191/01 HT-Steel spur gear 48 teeth

Fits the y0190/48 HT-Alloy carrier with steel spur gear 48T for the layshaftInner diameter and bolt pattern are the same as a standard FG differential spur gear.Module: m=1,5Content:1 piece

€49.90*

6491 FG Steel spur gear 44T with adapter - set

Hardened steel gearwheels for the gears of the 1/6 off-road models.Module: m=1,5

€93.90*

Details

6493/01 FG Steel spur gear 48T - 1 pce.

Item N° 6493/01 Steel spur gear 48T - 1 pce.Outer diameter: 75 mmInner diameter: 26 mmBolt circle: 3 x 35 mmWidth: 10 mmModule: m=1.5

€59.90*

y1427 HT steel spur gear on-road with 39, 40, 41 teeth

y1427 Version: y1427/41 HT steel spur gear

Fits FG and Smartech touring cars in combination with HT aluminum layshaft spur gear carrier on-road y1428. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions

€49.90*

Customers also viewed

y0897 Wheelie bar with suspension for 2WD + 4WD models - 1pce.

Wheelie bar with double ball raced wheel, cnc-machined from high strength alloy. The arm has a rubber suspension unit, the height is infinitely adjustable. The suspension allows for a maximum deflection of 30 degrees and is dirt- and mud-proof. The wheel bearings are sealed.The unit fits FG Monster Truck, Monster Beetle and Marder BigFoot, except for Monster Buggy Off-Road WB535 4WD. Installation on other models will be possible, but requires modifications to the chassis, mainly to accept the bolt pattern. The Carson Attack already has the correct pattern.

€89.90*

FG Sportsline 2WD-465 Electric Porsche GT2, up to 200A

The 2WD-465 Sportsline electric model is based on a short chassis (465 mm wheelbase) with double wishbones Rear and front axles built. The vehicle is factory equipped with the 2-damper front axle.E stands for electric power which is equivalent to extremely high torque, high speed and all this without any engine noise. The Sportsline models are equipped with a powerful brushless engine and a Brushless ESC. This control can be regulated simply via transmitter or optionally via the program card.In the unpainted version Version does not include a decal sheet!Features:The front axle of the GT2 was widened to 384 mm. The rear axle is 395 mm wide.Chassis short 465 with double wishbones on the rear and front axle completely assembled, ball bearings, differential gear, oil pressure shock absorber, multi-part unpainted polycarbonate body (item no. 05160L), white spoke rims, tires and tire inserts.T2M standard equipment brushless motor and ESC, 6S - 150A controller up to 3-6S - brushless motor 6S You can order a motor/ESC combination with 8S for an additional charge.- ESC 200A, 3-8S LiPo, BEC 8A - Brushless Motor 8S The model is also available in our shop selection including complete RTR equipment! RTR features RTR = Ready to Run. The RTR version is delivered ready to drive and with the 2.4 GHz remote control installed.Decor set: selectable (included in the painted version)LiPo batteries and the appropriate charger are required for all versions of the electric models. We recommend using LiPo batteries with a maximum length of 150mm and a width of 50mm to ensure trouble-free installation. The model is supplied with an EC8 connector system.

From €1,199.95*

Configure now

LOS05014V2T2/E Losi 5ive-T BEAST 2.0 V2 Electric 12S 1/5 4WD SCT BND

With our 12S Beast Edition you can choose between 2 variants:1. Hobbywing Ezrun Max5 HV ESC 250A up to 12S LiPo BEC8 and Ezrun 650KV 4pol brushless motor, without surcharge.2. Hobbywing Ezrun Max4 HV ESC Sensorless 300A up to 12S LiPo, BEC 10A and Top Tuning Beast Brushless Motor 620KV 4pol, 190,00 € extra charge. When the original 5IVE-T was introduced the world of 1/5-scale off-road racing changed, and this iconic platform became one of the most successful and influential platforms to date. Now get ready for 2.0! The Losi 5IVE-T 2.0 BND: 1/5 4WD Gas Short Course Truck has all of the unrivaled performance of its predecessor and includes Bind-N-Drive technology, allowing you to pick the transmitter that best fits your lifestyle. Comes with y1549/01 ZTW Beast Pro 300A 12S ESC and 520KV brushless motor and TT1021 Top Tuning Electric conversion kit for the ZTW BEAST version included.The revised chassis layout reduces the front drive shaft angle for improved durability and increased 4WD balance. Plus, the new rack style bellcrank steering assembly makes for easy Ackermann changes and overall improved steering geometry. Additional advances include an updated front hood, and hard anodized bleeder caps and shock bodies for improved shock performance. All this ensures the 5IVE-T 2.0 continues to reign supreme.Key Features Without surcharge : Ezrun MAX5 HV G2 ESC 12S and Ezrun 650KV brushless engine. Surcharge 190€ : Ezrun MAX4 HV G2 ESC and Top Tuning BEAST 620KV Brushless engine. Innovative Bind-N-DriveSpektrum 6200A DSMR 6-Ch AVC Telemetrie receiverImproved bar style steering rack with adjustable AckermannImproved center differential orientationImproved drive line angleHeavy-duty brakesTough steering and gas/throttle servo braceExtra-large 800cc capacity fuel tank What's in the Box?Losi 5IVE-T® 2.0 BND 4WD SCTSpektrum 6200A DSMR 6-Ch AVC Telemetrie receiverS900S 1/5 Scale Metal Gear Steering ServoWheel WrenchRod End/Shock End toolMulti WrenchSpark Plug WrenchBind Plug2.0mm, 2.5mm, 3.0mm, 4.0mm Allen WrenchesProduct ManualEC8 plug connection for optimum power transmission18 teeth pinionSpecification:Continuous Current: 250/300A ESC EzrunWaterproof: spash protectedBrushless Motor 650/620 kV Driving batteries with the following maximum dimensions can be installed: Length: 165 mm Width: 51 mm Height: variable The speed controller (ESC) requires EC8 connections or corresponding ! Contents:1 piece If you run the maximum operating voltage approved for an esc, there is a risk, especially in large scale cars, that under certain circumstances the reverse currents generated by the motor when braking will destroy the esc.For this reason, we recommend using a mechanical brake (as with gas powered vehicles) and deactivating the brake in the esc programming.Please note that reversing is then no longer possible!

€2,299.00* €2,487.80* (7.59% saved)

Configure now

LOS252076 Losi Outdrive Set Fr/Rr, Super Baja Rey / 2.0 / Super Rock Rey

Genuine Losi spare/option part. Contents:2 pieces

€19.99*

SB010/+2MM GPM Axle extenders 2 mm Losi Super Baja Rey/ Rock Rey

Genuine GPM spare/option part. Axle extenders for Losi Super Baja Rey / Rock Rey, 2 mm per side (4 mm in total). 20 mm hexagon, matching the original rims. Since the driving pins are no longer completely secured by the rim when using axle extenders, special threaded bolts are used for this application.The set also includes closed wheel nuts to protect the outer edge of the thread.2 axle extenders2 threaded steel pins2 closed wheel nuts

€18.90*