y0191 HT-Steel spur gear 46 teeth

Normal price: 249,90 EUR Tuning front disk brake system for the HPI Baja 5B/SS/5T/5sc, the conversion kit includes all necessary parts. The brake includes the finest parts available for a cable brake and has the following features: * uses existing mounting points for all parts * brake pads and 70 mm diameter stainless rotors made by RS-5, the best performing combination available * hardened stud bolts for the brake pads * billet brake levers, no tweak and best transfer of servo power * ultraflex bowden cables * brake cams run in hardened steel bushings and brass guide plates (miniature bearings don't last in offroad cars) * billet alloy bowden cable support block with adjustment screws * billet alloy bowden cable mounts at the calipers * pre-assembledOn a 5T the stud bolts which hold the brake pads will interfere with the ribs in the rim. However, modifying the rim or swapping the stud bolts for long csh screws allows for installation on a 5T.Spare parts for this brake as a PDF-file with spare part numbersWe highly recommend the installation of a stronger throttle servo to take full advantage of this brake system. The is an excellent choice.

Nitrided hardened, highly wear-resistant.Not suitable for Smartech and Carson models.  Suitable for FG offroad models 2WD on the clutch bell to the 42 main gear.  This pinion is profile shifted and has a 1.5 module.  This means that the number of teeth of the gear is changed compared to the previously known values while the diameter remains the same. The area of the involute curve that determines the tooth profile is shifted. Positively shifted gears (fewer teeth than normal) are more stable and run more smoothly; the slightly lower strength of negatively shifted gears is irrelevant.  1 piece

Highlights News 2025 Tuning aluminium lower wishbones, one-piece (front and rear) FG hydraulic brakes front and rearTuning chassis plate black anodised and milled Tuning milled aluminium rear axle linkage for toe-in adjustment  Perforated tuning clutch bell Side flaps on the rear spoiler in carbon fibre Highlights Formel 1 Competition- This model is fitted with numerous aluminium parts: - front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Technical description of the FG Formula 1 Competition :The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with FG hydraulic brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition CNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ Zenoah engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, FG hydraulic brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos (each approx. 40 - 50 kg), 2 servo for throttle brake (approx. 20 - 30 kg), batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engineAirboxPipe Clear bodyshell and polycarbonate spoiler FG hydraulik brakes front and rearDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!