y0692 HT-Gearset for layshaft and differential fine pitch for 1/5 onroad

€79.90*

Available

Product number: y0692

EAN: 4058575034469

Product information "y0692 HT-Gearset for layshaft and differential fine pitch for 1/5 onroad"

Genuine HT spare/option part.

Fine pitch gears for layshaft and differential, for competition use in touring car and GT models only. The gears run smoother and quieter than the stock parts, reducing the car's rolling resistance.

Module: m=1

Fits FG and Smartech / Carson cars. Only for use as a set, not in combination with standard pitch gears!

Contents:

2 pieces

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

y1426 HT aluminum gear carrier -on-road- with steel spur gear for the layshaft

Fits FG and Smartech touring cars. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions. The following measures are required for installation of the HT-steel gear adapter "on-road" on the layshaft in FG EVO 2020 cars:- The installed wide 16T layshaft pinion 6431/01 must be replaced by the narrow version 6431.- The supplied 1mm shim must be added between layshaft pinion and ball bearing.- The flat sections on the layshaft do not have the usual 180° offset for the adapter; therefore only one grub screw will be used. However, since this is a wide face M8 version, this is no disadvantage.

€69.90*

Configure now

y0191 HT-Steel spur gear 46 teeth

Fits the y0190/46 HT-Alloy carrier with steel spur gear 46T for the layshaftInner diameter and bolt pattern are the same as a standard FG differential spur gear.Module: m=1,5Content:1 piece

€49.90*

y0119 Steel pinion 16 teeth

Steel pinion 16 teeth suitable for 46 mm main gear for FG models.Modul 1,5

€29.90*

6048 FG Steel gearwheel big 48 teeth

Genuine FG spare/option part. Differential spur gear for all FG street cars except Formula 1. Can also be used as a main spur gear on the layshaft on monster models when mounted on alloy gear carrier y0190.Dimensions:Outer diameter: 75 mmWidth: 7.5 mmBore: 45 mmModule: m=1,5Contents:1 piece

€52.90*

6493 FG Steel spur gear 48T with adapter

Genuine FG spare/option part. Hardened steel gearwheels for the gears of the 1/6 off-road models.Module: m=1,5Contents:1 set

€93.50*

6492 FG Steel spur gear 46T with adapter - set

Hardened steel spur gear for FG 1/6 off-road models, spur gear diameter 72 mm.Module: m=1,5

€97.90*

32452 Gear 1 - 1pce.

cs_32452 Quality: nitrided+ 8.7EUR

Differential spur gear 48T for Carson / Smartech 2WD cars.Module: m=1,5

Variants from €44.90*

€53.60*

y0190/46 HT-Alloy carrier with steel spur gear 46T for the layshaft

This carriers makes it possible to run steel spur gears on the layshaft. Pebbles heat and the high torque of monster truck applications are no longer a problem.The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of the pinion and the spur gear carrier are pointing to the outside of the car. The carrier features M8 (eight, no typo) grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution.

€89.90*

6491 FG Steel spur gear 44T with adapter - set

Hardened steel gearwheels for the gears of the 1/6 off-road models.Module: m=1,5

€93.90*

y0191/01 HT-Steel spur gear 48 teeth

Fits the y0190/48 HT-Alloy carrier with steel spur gear 48T for the layshaftInner diameter and bolt pattern are the same as a standard FG differential spur gear.Module: m=1,5Content:1 piece

€49.90*

7432/29 FG Primary gears 37 teeth

Genuine FG spare/option part. ClutchGear shaft outerGear shaft innerDifferentialReduction ratio345823735,41345823745,49345824735,19345824745,26355823735,26355823745,33355824735,04355824745,11365823735,11365823745,18365824734,90365824744,97375823734,98375823745,04375824734,77375824744,84Contents:1 piece

€32.90*

6493/01 FG Steel spur gear 48T - 1 pce.

Item N° 6493/01 Steel spur gear 48T - 1 pce.Outer diameter: 75 mmInner diameter: 26 mmBolt circle: 3 x 35 mmWidth: 10 mmModule: m=1.5

€59.90*

Customers also viewed

32452 Gear 1 - 1pce.

cs_32452 Quality: nitrided+ 8.7EUR

Differential spur gear 48T for Carson / Smartech 2WD cars.Module: m=1,5

Variants from €44.90*

€53.60*

Carburetor Walbro WT 1107 with choke normal/ball-raced

Walbro Vergaser WT1107 with choke Standard carburetor for Zenoah G320. Typ: Walbro WT1107This is the stock carburetor used for the G320RC engine, and will also work on all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23 cm³ up to over 30 cm³. Dimensions:Bore: 15,88 mmVenturi: 13,5 mmIndependent tunable high and low speed jets.The carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23 cm³ up to over 30 cm³.

€69.90*

Configure now

y1137/04 GPM-Big Bore Premium shock absorber for FG Monster/Stadium Truck 4WD, set

Set consists of 4 dampers. Premium version, suitable for FG, Carson / Smartech etc. Fully assembled and filled. Special features: 16 mm inner diameter for higher oil volume Volume equalisation Housing and screw connections made entirely of aluminium Hard anodised housing Precision piston made of Delrin, machined (no moulded part!) Aluminium piston rod base and aluminium spring plate Replaceable bearing bushes in the mounting eyes Pre-filled with 1000 silicone oil. For the following models: FG 4WD: Monster Truck, Monster Jeep, Monster Hummer, Stadium Truck, Stadium Jeep, Stadium Hummer, Off-Road Beetle Set contents: Four long dampers with 5 mm mount in the upper damper caps. Damper feet one pair short, one pair long (4WD MT version). We recommend our progressive off-road tuning shock absorber springs from the "Dirt-Spring M" series, part number y0321, for the shock absorbers. The original springs can also be used on FG models! Silicone oil recommendation: The GPM-Spezial Cross shock absorbers are filled with silicone oil viscosity 1000. This viscosity provides very good damping properties at normal outside temperatures. If softer damping is required, oil with a viscosity of 500 or 600 is recommended; for harder damping, 1500 or higher is recommended. One 50 ml bottle of y0038 is sufficient for five long or six short dampers.

€149.90*

4159 FG Audi RS5 DTM clear

Genuine FG spare/option part. Audi RS5 DTM clear body shell for 1/5 cars with 530/535 mm wheelbase.The set includes main section and front air dam as well as the required special screws.The body shell does not come with drilled mounting holes to make it possible to fit any 1/5 car with 530/535 mm wheelbase.Rear wing, side flaps/winglets and several decal sets are available from the options menu.The front section is also available separately as a spare part with part number y1441/01.This Audi RS5 DTM body shell is also available fully painted with either Team Audi Ultra (y1441/06) or Team Jägermeister (y1441/07) design.Required body mounts:Mount front: FG 7020/14 Front bumper Rear body mount: FG 7152/01 Rear body mount Side body mount front: FG 3014 Body mounts Side body mount rear: FG 3014 Body mounts / for 4WD: FG 7014/02 Body mountContents:1 set

€264.95*

41120, FG Stadium Jeep body shell, red, for 2WD for WB535

The bodyshell is made from colored polycarbonate.Length approx. 670 mmWidth approx. 300 mmHeight approx. 225.mmWheelbase approx. 470 mm

€170.00*

32407 Differential mounts rear left/right - 2pcs.

€16.90*

y0266 HT-Differential ring gear, fine pitch, 69Teeth

Genuine HT spare/option part.Fine pitch gears for layshaft and differential, for competition use in touring car and GT models only. The gears run smoother and quieter than the stock parts, reducing the car's rolling resistance.Fits FG and Smartech / Carson cars. Only for use with the fine pitch pinion! Module: m=1.Contents:1 piece [INCLUDE]profilverschoben[ENDINCLUDE]

€49.90*