GPM air filter cover which fits easily over your existing air filter. A rubber band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments. Fits all common filters, foam or fabric (K&N) style.
Keeps cool air coming to your engine by keeping dirt and grass from clogging up the pull starter area. Easily wipe off anything not deflected away. Installs on the starter cover with hook & loop tape. With metal cable management.If using a FG monster / stadium model an additional hole for the support of the lateral carrier plate has to be cut out.
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³. incl. clutch spring!Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!
Length 12 mmInner diameter 3.3 mmWire diameter 0.3 mmSpare part for , , , , , , , , , , and .
Genuine FG spare/option part.Dimensions:Inner diameter: 2 mmCollet outer diameter: 7 mm x width 5 mmOuterdiameter: 5 mm x width 8 mmContents:4 pieces
The spark plug tester wiil be put in line between the spark plug in the engine and the spark plug cap. When the spark plug is in good working order, pulling the recoil starter will produce a spark easily visible in the clear section of the tester (see video!).
Highly flexible driveshaft boots, equivalent to HPI part # H86479.Available in the following colors:y86479/01 - blacky86479/02 - redy86479/03 - orangeContents:4 pieces
Genuine HPI spare/option part.Fits all cars from the HPI Baja 5line with Zenoah or CY (Fuelie) engine. Content:1 piece
Reinforced spring for Zenoah OEM clutch with 2.7 mm wire diameter and five coils. Engagement speed is around 7500 rpm, which allows the engine to build up more power and torque for accelleration.Fits Zenoah, CY and most other engines in the 23 - 30 cc range with stock clutch.
Genuine HPI spare/option part. Part is delivered in silver or black color from vendor!Content:6 piece
To ensure the required cooling for current 1/5 and 1/6 engines the flywheels have fins on both sides. Therefore the fan housing has large openings on the crankcase side for the required air supply. However, the risk of foreign objects (grass, sand, or even stones!) entering here Is very high! As a result, broken fins on the flywheel occur frequently. This leads to reduced cooling efficiency and - even more critical vibrations from a flywheel which is out of balance due to missing fins. Therefore, this kind of flywheel protection is highly recommended, especially for offroad use. The product video explains the handling in detail! Note:It is essential to thoroughly clean and degrease the crankcase prior to attaching the hook-and-loop tape (OKS2661)!For installation on Chung-Yang and Zenoah engines in FG cars, the crankcase cover must be slightly modified in two places where the engine mount is attached (see Figure 6 and 7). Furthermore the fit of the fabric must be as tight as possible in the region of the layshaft pinion (in front of the differential ring gear!) (see Figure 8).Set includes:Special tailored fabric with sewed on hook-and-loop tapehook-and-loop tape for installation to the crankcaseAdhesive for securing the hook-and-loop tape
Genuine HT spare/option part. Hardened special screws for mounting the beadlock rings of MadMax and Losi DBXL rims.For HPI rims due to the screw head diameter only to be used in combination with non-HPI beadlock rings (i.e. MadMax or Losi 5ive-T)!The combination of larger diameter and substantially larger thread depth ensures a secure grip of the screws in the plastic of the rims; the coarse thread also allows for quick assembly.The large head with T10 hexalobular drive distributes the load as wide as possible on the ring.The screws are galvanized for rust protection.Please note: it is not recommended to use the screws in rims which had previously M3 screws installed. With new rims or in exchange for M2.5 screws appropriate strength is ensured.Dimensions: Diameter: 3,1 mmLength: 12 mmHexalobular drive: T10 (Torx) Content:1 Set of 40 screws for one pair of rims.
Genuine FG spare/option part. Spare part for:6250/016250/026250/056250/068450/018450/0584528452/0510450104511045210453Content:2 pieces
Genuine Atop spare/option part. Colored fuel hose with clams and suction tubesArea Rc High flow fuel line kit.This high flow fuel line kit fits the HPI Baja series and the Losi 5ive-T/B and Mini. It may fit other large scale cars as well.The kit comes with 6 pieces of fuel line clips and 2 assembled plastic fittings. Those fittings cannot be compressed by the tanks fuel line grommet, so the inner diameter remains constant which improves fuel delivery to the carb.Fuel line dimensions:Length: 1mInside diameter: 3 mmOuter diameter: 6 mmAvailable colors: AT001/01 - YellowAT001/02 - RedAT001/03 - BlueAT001/05 - GreenIncludes:2 x Assembled plastic fittings6 x Fuel line clipsTygon fuel line
Genuine HPI spare/option part. Contents:4 pieces
Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!) Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!) The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended. For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.Attention:Clutch-Safe adhesive must be stored in the fridge! Content: 10g tube
Content: 10 Gramm (€495.00 / 1000 Gramm)
Can be used as reinforcement for genuine HPI and Losi rims as well.Set includes:Two pieces of reinforced outside ringsTwo pieces of reinforced inside ringsand 40 pieces of 3 mm allen head screws (for 2,5 mm allen wrench)Colours:y1418/02 - Bluey1418/03 - Redy1418/05 - Yellow
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece
Genuine HPI spare/option part. Dimensions: 12 x 24 x 6 mm.Content:2 pieces
Genuine HPI spare/option part. Fits a huge range of RC cars and trucks, and conveniently packaged in packs of 20 for quick replacement. Cool black colour to match every paint scheme.Content:20 piece
Hardened steel bushes for all caliper of the front and rear disk brakes. In combination with a ball-beared guide plate optimal position of the brake eccentric.Substitute for , , , , and .
Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface whichguarantees dimensional stability even under high loads!Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM clutches Big Scale Extreme and Cross.Suitable for slot drive HPI Baja pinions, both stock using a 4mm bolt and aftermarket ones for 5mm bolts. Comes with M4 and M5 bolts included.
