y1337 Epoxy P-R-M Race brake discs for FG / Smartech / Carson
€22.90
Available
Product information "y1337 Epoxy P-R-M Race brake discs for FG / Smartech / Carson"
The epoxy P-R-M Race brake disc provides an optimal deceleration of the car without the unwanted fading (poor braking performance due to increased heat buildup)!
The best braking action when using the epoxy P-R-M Race brake disc is achieved by the combination of the epoxy brake discs and steel brake pads (8456 or y19218).
The epoxy P-R-M Race brake discs fit mechanical front and rear brakes on FG / Smartech / Carson cars with brake pads 8456 recommended for these applications.
1 pair (2 pieces)
Dimensions:
- Outer diameter: 60 mm
- Thickness: 2 mm
- socket for 18 mm square wheel drive
Login
Accessories / Spare parts
Genuine FG spare/option part. Suitable for .Content:6 pieces
Customers also bought
Fits FG and Smartech touring cars. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions. The following measures are required for installation of the HT-steel gear adapter "on-road" on the layshaft in FG EVO 2020 cars:- The installed wide 16T layshaft pinion 6431/01 must be replaced by the narrow version 6431.- The supplied 1mm shim must be added between layshaft pinion and ball bearing.- The flat sections on the layshaft do not have the usual 180° offset for the adapter; therefore only one grub screw will be used. However, since this is a wide face M8 version, this is no disadvantage.
Genuine FG spare/option part. Suitable for rc-plate 5014.Dimensions:Inside length: 44 mmInside width: 20,5 mmContents:2 pieces
Genuine FG spare/option part. Spare part for: 7331.Contents:1 piece
Customers also viewed
Suitable for all mechanical disk brakes.
Genuine FG spare/option part. Suitable for .Content:6 pieces
Genuine FG spare/option part.Suitable for all FG shock absorbers and also for other makes with an outside diameter of 16 mm.Dimensions:Length: 58 mmOutside diameter: 20 mmWire diameter: 2,7 mmContents:2 pieces
You can select the tyre hardness above: - Hurrax HX100 extreme Grip Medium 175/70 mm tyre and - Hurrax HX400 extreme Grip Soft 175/70 mm tyre HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece