6039/10 FG Gear plate

Genuine FG spare/option part. Washers for the screws (M4 / M5) that hold the engine mounts to the chassis. Suitable for all FG models.Dimensions:Outside diameter: 15 mmInside diameter: 6 mmContents:4 pieces

Genuine FG spare/option part. Reinforced plastic ball-and-socket joints for M8 thread rods. Replacement for the plastic ball-and-socket joints 6029/01.Fits 10 mm balls, total length 39 mm.Contents:4 pieces

Genuine FG spare/option part. Rubber pucks for all standard design FG spur gear carriers.Dimensions:Outside diameter: 16 mmInner diameter: 7 mmHeight: 6 mmContents:4 pieces

Genuine FG spare/option part. For all FG models except Formula 1.Dimensions:Length: 103 mmDiameter: 10 mmImportant:When installed in a Carson / Smartech model the brake hub is fastened with a screw stomach.Content:1 piece

Genuine FG spare/option part. Fits all FG 1/6 off road cars, alloy version.Length of threaded section approx. 17 mm.Contents:2 pieces

Genuine FG spare/option part. Reinforced plastic ball-and-socket joints for M6 thread rods. Replacement for the plastic ball-and-socket joints 6029.Fits 10 mm balls, total length 39 mm.Contents:4 pieces

Genuine FG spare/option part. Dimensions:Wire diameter: 3 mmInner diameter of eyelet: 12.3 mmContents:1 piece

Genuine FG spare/option part. Plastic version, 60 mm diameter. For 48T - 46T spur gears.Also available in aluminum .Content:1 piece

Genuine FG spare/option part. Stock spur gear for all FG monster cars.Suitable for spur gear carriers: 6050 (plastic) 6439 (aluminum)Dimensions:Diameter: 75 mmWidth: 15.5 mmTooth width: 12 mmModule: m=1,5 Contents:1 piece

Item N° 6037/01 Steel mounting plate - 2pcs.Connects the large engine mount to the engine flange on all FG cars except evo 04 / evo 07 / competition 07Bulk:large extent plate:length: 35 mmwidth: 10 mmheight: 2 mmsmall extent plate:length: 25 mmwidth: 10 mmheight: 2 mm

Genuine FG spare/option part. Plastic ball joint Fits all FG cars.Dimensions:Thread size: M4Länge: 20 mmBall bore: 3 mmHeight: 8 mmContents:6 pieces

Genuine FG spare/option part. Brake disc for single disc brake (97 up).Dimensions:Diameter: 52,5 mmSquare size: 18 mmContents:1 piece

Genuine FG spare/option part.Plastic gear plate for single disc brake (off road version). Bearing seats clutch bell: 22 mm x 6 mmBearing seat layshaft: 19 mm x 7 mmContents:1 piece

y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

Also available in .Old version for brake with two small discs.

Item N° 67214/04 Mini block S / OR tires, glued, white, 2pcs.Completely new revised and in important details improved Mini Block Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant.The FG Mini Block tires are especially well-suited for slightly loose and humid ground. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle. The Mini Block tires are also well-suited as front tires for 2WD models in combination with the Mini Pin tires on the rear axle. The tires are ready glued on the new Leo 1:6 wheels. For the assembly you need the 12mm square wheel drivers (ItemN°. 06107/07).The glued tires are not suitable for the FG models Marder, Beetle, Off-Road Buggy and Monster models.

Fits Zenoah Tank 7348ID 3 mm x L 470 mm

Cylinder-piston repair kit for 23 cm³ or 26 cm³ Losi 5ive-T engine. The set includes the following parts:Cylinderpistonpiston ringcylinder foot gasketpiston pin clipPlease note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer

Item N° 6039/05 Gear plate 06 - setNew gear plate with metal brake plates and big Epoxy brake disk, therefore higher braking power with less heat development.Bearing seats clutch bell: 22 mm x 6 mmBearing seat layshaft: 19 mm x 7 mmContent as shown