The brushless Big Scale servo is an extremely robust digital servo, with a high performance brushless motor, in absolute premium quality, with a full aluminum case for optimal heat dissipation in the 2-version with elaborate cooling fins, metal gears and equipped with high-quality 30 cm long silicone insulated cable. Where with other high-performance servos you still have to buy an aluminum top or case as third party options, the brushless Big Scale servo already comes with a full metal case, and above all, the aluminum to features special bushings for the intermediate shafts! Of course, the support from a metal top cover guarantees a much longer service life of the complete gearbox, than with a plastic version! Defective gears are known to be the most frequent cause of failure; especially for highly stressed servos in 1/5 and 1/6 cars! The brushless Big Scale servo is also the first choice for 1/8 and 1/10 race cars, where fast reaction times and high steering forces bring up the demand for an extremely fast and reliable servo! Also, servo mounting tab breakage on the servo cover is virtually impossible with the brushless Big Scale servo. Dimensions:Length: 40 mmWidth: 20 mmHeight: 41.4 mmWeight: 72 gramsPerformance:7.4 V6 VHolding torque kg-cm/oz-in30.0/41726,0/361Speed sec./60°0.110.14Accessories included:Three different plastic servo horns / discFour each rubber grommets and guide sleevesMounting screwsNote: Due to the extreme holding power of the brushless Big Scale servo the rubber grommets should always be installed in combination with the guide sleeves. The brushless Big Scale servo comes with accessories in a high quality plastic case with molded insert.We recommend an aluminum servo arm from the selection of the article:Alloy servoarms, for 25 teeth multi-tooth shaft 9,90 EUR
Genuine K&N spare/option part. The K+N air filter oil is only suitable for all K+N air filters, foam preliminary filters and filter inserts.Content:1 piece / 204 ml
The offroad tire combination!V-Pin front and Mammoth wide tires in rear are the unbeatable combination for offroad use.combi set:Mammoth ready glued: 99,90 EURV-Pin ready glued: 78,80 EURTotal: 178,90 EUROffer price: 99,99 EURDescription for V-Pin tires:The V-pin competition tire is particularly suitable for tracks with loose and sandy surface.The high tread profile, extended to the tire shoulder requires a high manufacturing cost.This tread design guarantees an extremely high side traction and provides maximum propulsion especially on surfaces like sand and loose soil for optimum. By cutting of the tread profile of the V-pin tires you can adjust your car's handling easily. The partly or nearly complete removal of the V-pin tire's tread on the outside of the tire, greatly affects the tire's side bite when cornering.Summarized: removing tread from V-Pin tires on the front axle will reduce oversteering, calm your car and make it easier to drive.When oversteering is extreme (e.g. high grass) you may even start cutting the tread on the inside shoulder. This can prevent your car from those annoying traction rolls.Diameter: 163 mmWidth: 65 mmPrices of the components V-Pin:V-Pin tires EUR 39.90 EUR / pairV-Pin tire inserts EUR 9.90 EUR / pairRims FG 6105/01 EUR 14.90 EUR / pairglue set y0067 EUR 13.30 EUR Total EUR 78.80 EUR Description for Mammoth tires:Extra wide tire mounted and glued on genuine 1/6 scale FG buggy rims 6105/01 with extension ring!The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall. Diameter: 165 mmWidth: 80 mmRim with 18 mm square driveThe Mammoth brings, due to its quite strong and large pins and the extreme width of the tire, especially on hard and low grip surfaces a high traction! Where other tires spin helplessly the Mammoth provides serious traction. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Combination for the HPI Baja and 5T cars will the rim extension rings glued on the inside!Unit prices Mammoth:Mammoth tires extra wide: 47.20 EUR / pairMammoth inserts extra wide: 9.90 EUR / pairgenuine FG wide track rims 6105/01: 14.90 EUR / pairgenuine FG rim extension rings 6436: 14.90 EUR / pairmounting + glueing rims / extensions / inserts / tires: 13.00 EUR Total: 99.90 EUR Mammoth ready glued: 99,90 EURV-Pin ready glued: 78,80 EURTotal: 178,90 EURIntroductory price: 99,99 EUR Also suitable for:With the following wheel adapter: y1183 Rim adapter
Genuine HT spare/option part. Universal decals suitable for all body shells. The decals are printed on white film and have to be cut out by yourself.Size (Height x Width):Complete sheet: 300 mm x 410 mmContents:1 piece
€14.90*
This website uses cookies to ensure the best experience possible. More information...