Product information "y0067 HT tire cement and activator"
Accelerator-spray is the second component to cure superglue immediately.
This set is also particularly suitable for the possible repair of loosened tire/rim gluing!
Advantages:
Tangible adhesion after a few seconds
Aromatic solvents and hexane free
Suitable for hobby, craft, industry and household
Processing:
Clean the surface thoroughly. Apply accelerator at room temperature on both surfaces to be bonded until a clear liquid film appears. Air out the applied accelerator, then apply the superglue as usual.
Contents:
Special tire cement ht 4000
Spray can activator
0 of 0 reviews
Leave a review!
Share your experiences with other customers.
Login
No reviews found. Share your insights with others.
This pair of Tyres have the following use indications: VERY HIGH GRIP situation for very clean track. VERY HIGH GRIP situation for big asphalt. VERY HIGH GRIP situation for very high temperatures. This pair of Tyres have the following technical features: REVO treated profile for the maximum traction and the maximum lateral grip. Treated profile studied to maintain the tyre surface alway clean from rubber murble. Compound exclusively developped for model tyres. Inside belt flexible but very strong, vulcanized directly together with tyre compound. Insert foam with special material for high temperatures, for maximum stability and high drive precision. Spoked wheel moulded with special material for high temperatures for maximum grip and stability. Special gluing system 100% guaranteed.The main sizes for this tyre are: WHEEL fixing with square 18mm. TYRE outside diameter 118mm. WHEEL inside diameter 90mm. TYRE tota width 65mm. Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!
Genuine FG spare/option part. Solid alloy wishbone mounts with 4mm boring for the FG Formula 1 Sportsline and Competition models.Six pieces per car are required.Contents:2 pieces
MadMax Monster tire LAND G-RIPPER 211x104 The off-road tire combination for extreme terrain use and "RC-car show use"! Glued on rims with 24 mm hex drive and reinforcement ring, suitable for Losi/HPI/Arrma/Traxxas/Carson1/5 series cars Dimensions: 211 mm outer diameter 104 mm width 875 grams weight Please note: Since the MadMax Monster LAND G-RIPPER tires give a very good grip, the rim and bonding are extremely stressed.Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Here you can find the other tire sets shown in the picture: ARRMA ARA550061 Losi LOS45017/S Carson B501
Off-road tires for sandy underground! Gives great results on those carpets which are typical for some off-road tracks. 462 grippy square studs per tire, a total of more then 1800 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability! Therefore the car is less prone to undesirable side rolls! The rim is the 6-spoke design with a steel reinforcement ring around the wheel drive. The NARROW-GRIP tires are available with either 18 mm square drive to fit FG & co. or with 24mm hex for Losi, HPI Baja 5 series cars and they allready glued!To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the square or hex drive and completely mounted via tightening the wheel nut! Dimensions:Outer tire diameter: 175 mmTire and rim width: 62 mmRim inner diameter: 119 mmWeight for one tire: 375 grams / for a pair: 750 gramshe manufacturer of the Narrow-Grip 462 indicates that the use of these tires on very heavy models, like the Losi 5ive-T under heavy conditions, such as jumps and shifting / tilting of the chassis, may lead to breakage of spokes or hex socket. Due to this notice that kind of failure will not be compensated. We apologize for this note!As an alternative, we recommend our special offer for the Losi 5ive-T OEM tires and in particular all tire combinations with MadMax EXTREME rims for FG, Smartech and Co.:y1400/01 - Tarmac Bustery1401/01 - Big Digger y1402/01 - Cross Bond y1403/01 - Over Lander y1404/01 - Giant Grip y1416/01 - Ultra Gripor for Losi and HPI models: y1406/01 - Big Digger y1407/01 - Cross Bond y1408/01- Over Lander y1409/01 - Giant Grip y1417/01 - Ultra Grip18 mm square for FG & co24 mm hex for Losi and HPI Baja 5 Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (18 mm square for FG & co24 mm hex for Losi and HPI Baja 5 Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. Wheels drives:18 mm square for FG & co.24 mm hex for Losi, HPI Baja 5 cars.Contents:2 pieces / 1 pair
The tire tread cutter is required for re-cutting worn-out or creating new tread designs in order to get more grip. Cutting depth is adjustable and cutting width is approx. 3 mm.Please note: This tool is designed for cutting model tires only, not for any fullsize vehicle tires!Content:1 pieces
Genuine FG spare/option part.With a Ø of 185mm extremely large and 85mm wide OR Truggy tire. A lot of grip, therefore high curve speeds on almost every surfaces possible. Available in different hardnesses. Suitable for all FG Buggy and Monster models. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Special cleaner for aluminumPower Clean is a safe, fast-acting cleaner/degreaser for almost all types of contaminated metal parts and surfaces. The product removes brake dust, tar, undercoating, grease and various waxes and any type of contamination. Power Clean is a non-hazardous cleaner for electronic brake and ABS systems. Since the product does not attack the substrate, it is also particularly suitable for removing tar splashes and grease and oil stains.Power Clean evaporates completely without leaving any residue. Another major advantage is that the product does not cause white efflorescence on aluminum parts, as is the case with most brake cleaners. Thus, Power Clean is the perfect product for cleaning clutch and engine parts. The product comes out of the spray can at high pressure, making it easy to clean hard-to-reach places. In the spray can, Power Clean is particularly user-friendly and practical to use. Highlights . span> harmless to aluminum. div> span> High spray pressure, therefore suitable for heavily accessible places. div> span> leaves no residues Content base: aliphatic hydrocarbons Density: 733 kg / m³ Consistency: liquid (firefitted in the aerosol can) viscosity: 2 mPa.s li> solvent: aliphatic hydrocarbons Flash point: 0 ° C Evaporation Residue: Maximum 4% Processing conditions: + 10 ° C to + 30 ° C SURFACES.Almost all types of metal, paints and plastics. Before use on plastics and paints, always test on an inconspicuous area. USAGESpray product on the parts to be cleaned and leave to act briefly. Re-spray to completely remove loosened dirt. Hand cleaning: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water Shelf life: 2 years in unopened original packaging Storage conditions: Store in a cool, dry place Batch code type: F
The MCD Astro-Grip is one of the most widely used tires in large scale off-road racing. Especially on astro turf and firm clay it provides optimal grip and is resistant to wear. The reinforced shoulder largely protects the tire from damage. Therefore the radial ribbing should normally be mounted on the outside of the. Due to the increased stiffness and some sort of added tread, the ribs also improve the tires traction during cornering.If this effect is not desired (i.e to reduce steering on the front axle), you can also mount the tires with the ribs to the inside, of course. It just has be considered when you glue the tires. Another way to reduce the tires grip at the outer edge is cutting some of the outer pins. This makes a tire less aggressive during cornering; another possibility to match the cars behavior to the track and make it more drivable. A pleasant vehicle setup can often be achieved by running used MCD Astro-Grip tires on the front axle and new ones on the rear.Dimensions:Outside diameter: approx. 180 mmInside diameter: approx. 130 mmWidth: approx. 65 mmWeight: one glued tire on Hurrax rim: 370 grams Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms
Wide neck flask with 50 ml.The "work of the devil!" The smell is normal! Among others this lubricant is suitable for the following model car applications:Drive shafts (if covered with boots)Transmission in enclosed housings (i.g. ring & pinion gears in Losi 5ive-T or Desert Buggy XL)Differentials which do not use friction padsChesterton® 787 Sliding Paste is a premium quality pure synthetic lubricant that will function effectively even at ultra high temperatures and pressures. Designed for the most severe operating conditions, it provides, through a novel chemical approach, lubrication at pressures up to 10687 kg/cm2 and 538°C.787 Sliding Paste is a unique thixotropic hybrid lubricant. Consisting of a semi-soft paste-like material, this product will flow to fill in small tolerances, yet will keep metal parts separated by the microscopic, symmetric, plates which slide over each other and provide effective lubrication long after the clean synthetic base oil has burned off. Applications for Chesterton 787 Sliding Paste can be found anywhere a need exists for a clinging semi-solid lubricant that will resist water washout and can withstand high temperatures and pressures. Unlike a grease which can turn to liquid and fail under extremely high loads and temperatures, 787 will maintain a slippery film on surfaces and prevent wear, galling and seizure at temperatures unthinkable for a grease. Use in such high temperature applications as lubrication of welding equipment, steel production facilities, smelting factories, forging furnaces, metal casting foundries, around exhaust stacks in power stations, turbine exhaust areas, and any other area exposed to extreme conditions. Because of its excellent resistance to water washout, the product works extremely well in outdoor applications such as on railroad switching equipment and wire rope cables.Composition:Chesterton 787 Sliding Paste is a unique hybrid material that suits the requirements of todays hotter running equipment. It consists of a combination of both organic and inorganic lubricating components and will perform effectively at temperatures ranging from -23°C to 538°C. The geometry of the solid constituents in 787 Sliding Paste is such that they slide over one another and remain undistorted even at the highest pressures parts and equipment are likely to see. The symmetry of the particles means they can withstand extra stresses compared to some inorganic materials which can shatter under extreme loads. The base oil used in Chesterton 787 Sliding Paste is a pure synthetic that will burn cleanly and leave no carbon or varnish to gum up parts and equipment. Because it contains no petroleum oils, it does not present the clean-up problems associated with waste petroleum residues.Features:Pure Non-Carbonizing, Synthetic Base n Lubricates at pressures to 10687 kg/cm n Withstands Temperatures to 538°CExcellent Water Washout Resistance n Non-Fling, Clinging LubricantLow Coefficient of FrictionNSF H2 - Registration number 133956 n No Toxic Heavy MetalsUltra-Fine ParticlesUnique 3 Phase Lubrication PackageApplications:Use in areas subject to extremes in temperature including smelting, forging, metal refining, glass manufacturing, plastics production, and in chemical, petrochemical and power plants, in foundries, around exhaust stacks, on rotary kilns in the cement and mining industry, etc. 787 is specifically designed to provide lubrication for surfaces subjected to extreme pressure. This would include wire ropes, cranes, railroad switch gear, and on large open gears on doors and bridges.Stem nuts, Lead screws, and Linear actuatorsFlange bolts and High tension studs n Press fit bushingsDirections:Brush or pump 787 Sliding Paste into areas needing to be lubricated. Product can be applied by squirt oiler. Spread evenly to thoroughly lubricate all parts and equipment which will see friction.Safety:Before using this product, please review the or appropriate safety data sheet for your area.
Special plastic cleanerPE100 was specially developed to protect plastics from external agents. The product penetrates right into the molecular structure of the plastic,which is thus protected from the inside out, remains permanently supple and retains its natural gloss.Most RC cars have various axle parts, such as control arms and bearing blocks made of plastic. Due to weather influences and especially UV rays,or contact with tire conditioners can cause the plastic to become brittle and weather over time.Especially with unpainted plastic, this process progresses relatively quickly. PE100 slows down this process and provides intensive protection,which significantly extends the life of the plastic. Also, the likelihood of seals and protective rubbers (e.g. bellows for drive parts) becomingbecome brittle are much lower.In addition to this protective effect, PE100 gives the plastic parts a fresher appearance. PE100 is also excellent for protecting electronic parts frommoisture in electronic parts. Das Produkt bildet eine wasserverdrängende Schicht und verbessert somit den Korrosionsschutz.In the spray can, PE100 is particularly user-friendly and practical to use. Thanks to the special nozzle with tube supplied, even difficult-to-reach areas can be treated effortlessly. Highlights H3> span> clear, almost invisible fluid div> span> Easy application div> span> displaces moisture div> span> Long-term effect div> span> protects plastics against discoloring div> span> holds rubber parts supple and prevents them freeze div> span> protects ignition systems from moisture-related disorders div> div>> CONTENTS base: silicone oils, mineral oils and additives Density: 710 kg / m³ Consistency: liquid (firefitted in the aerosol can) viscosity: ± 15 mPa.s li> Flash point: 0 ° C compressive strength: minimal li> temperature resistance: -20 ° C to> 150 ° C li> water resistance: good li> acid resistance: resistant to dilute acids li> corrosion protection: good. Corrosion protection results from the formation of a water-displaced layer. Inputs: good li> lubricant content: 17% li> Processing conditions: + 5 ° C to + 40 ° C Underground: Most plastics, rubber and metal USAGEPreparation of the substrate: Provide a clean, dry, grease-free and non-corroded substrate.Shake can well before use. When used as a lubricant, spray the product directly onto the part to be lubricated. When used as a plastic and rubber protector, spray the product directly (spray distance 15-20 cm) or apply with a cloth or sponge. To achieve a beautiful shine, briefly polish the plastic with a clean, dry Multi Wipe. Material cleaning: With Innotec Multisol or Innotec Power Clean Hand cleaning: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water Shelf life: 2 years in unopened original packaging Storage conditions: Store in a cool, dry place Batch code type: F
Genuine FG spare/option part.When adding this grease in the differential you achieve a blocking effect according to its sticky nature. Only for standard differentials, not for the adjustable differentials.Contents:1 piece / 50 ml
€11.90*
This website uses cookies to ensure the best experience possible. More information...