18 products found for "y1461"
rc-car-online - Home
Audi RS5 DTM clear body shell for 1/5 cars with 530/535 mm wheelbase.The set includes main section and front air dam as well as the required special screws.The body shell does not come with drilled mounting holes to make it possible to fit any 1/5 car with 530/535 mm wheelbase.Rear wing, side flaps/winglets and several decal sets are available from the options menu.The front section is also available separately as a spare part with part number y1441/01.This Audi RS5 DTM body shell is also available fully painted with either Team Audi Ultra (y1441/06) or Team Jägermeister (y1441/07) design.Required body mounts:Mount front: FG 7020/14 Front bumper Rear body mount: FG 7152/01 Rear body mount Side body mount front: FG 3014 Body mounts Side body mount rear: FG 3014 Body mounts / for 4WD: FG 7014/02 Body mount
Genuine HT spare/option part. Handy wrench for 6 mm turnbuckles.Maße: Wrench size: 6 mmLength: 75 mmContent:1 piece
Fits most spray cans from many manufacturers.Convert your spray can into a spray gun. The long-lever system of this handle makes using a spray can much more convenient and provides better flow rate control as well.No more dirty hands from paint work.Contents:1 piece
Genuine HT spare/option part. Once again misplaced nut or bolt or, or ... . The tray for small parts with magnetic vinyl brings this to an end!Dimensions: Length: 105 mmWidth: 85 mmdepth: 10 mmContent:1 Piece
The perfect tool for drilling perfectly round holes without cracks into a body shell.The cap protects the extremely sharp and spiky tip, the convenient handle provides secure grip on the tool.Dimensions:For holes up to 14 mm diameterLength of tip: approx. 45 mmTotal length: approx. 132 mmContent:1 Piece
Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The BIG DIGGER tires had 84 extremely strong tread blocks on the front tires and 96 on the rears, with more than 1 cm² cross-section and 6 mm tread depth, allow for best power transfer and provide excellent grip even on loose surfaces like sand or soil. Dimensions:Outer diameter: 170 mmTyre width front: 60 mmTyre width rear: 80 mmContents:4 pieces / 2 pairs Some off-road tires knowledge can be found here!
Genuine Speed Tec spare/option part. Speed TEC Tuning Ignition Löhin RS4 332 new ignition system with offset ignition timing and modified spark breakaway. Advantage of the ignition system: better starting and acceleration due to the modified ignition timing. Higher ignition voltage through modified spark breakaway, resulting in increased charging time for the coil, thereby considerably more torque in the medium rpm range. Suitable for Zenoah and CY engines without modifications. In the picture you can see the original Löhin ignition.Contents:1 piece
Genuine HT spare/option part. For the optimal measurement of the chassis.Steel rulers, 150 and 300 mm long.Contents:2 piece
Single spare parts to replacement number: y0460Ceramic ballbearing fits on the alloy and plastic front axle housing for all FG 4WD models.Dimensions: 6 x 15 x 5 mm
The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video).On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks! Some off-road tires knowledge can be found here!
y1465 Version:
screws only
Genuine HT spare/option part. Hardened special screws for mounting the beadlock rings of MadMax and Losi DBXL rims.For HPI rims due to the screw head diameter only to be used in combination with non-HPI beadlock rings (i.e. MadMax or Losi 5ive-T)!The combination of larger diameter and substantially larger thread depth ensures a secure grip of the screws in the plastic of the rims; the coarse thread also allows for quick assembly.The large head with T10 hexalobular drive distributes the load as wide as possible on the ring.The screws are galvanized for rust protection.Please note: it is not recommended to use the screws in rims which had previously M3 screws installed. With new rims or in exchange for M2.5 screws appropriate strength is ensured.Dimensions: Diameter: 3,1 mmLength: 12 mmHexalobular drive: T10 (Torx) Content:1 Set of 40 screws for one pair of rims.
y1466 Version:
y1376 Full set of gaskets for Zenoah G240, G270, G290, and 4-Bolt Losi, HPI, CY engines
y0467 Complete gask set for Zenoah 230 + 260, CY, Reely, HPI and Losi 2 bolt engines, setHigh quality gasket set for all G230 and G260 Zenoah engines, all Chung Yang, Reely an HPI Fuely engines from 23 to 30,5 cc. Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Set includes gaskets for:cylinder bottomcarburetorisolatorexhaustcrankcasey1376 Full set of gaskets for Zenoah G240, G270, G290, and 4-Bolt Losi, CY enginesFull set of gaskets for Zenoah G40, G270, G290, and 4-Bolt CY engines.Set includes:0.4 mm cylinder gasket (Zenoah stock thickness!)1 mm exhaust gasket0.5 mm crankcase gasket0.5 mm isolator gasket0.5 mm carburetor gasket0.5 mm air filter gaskety1016/112 Complete Zenoah G320 sealing setSet includes:y1016/005 Cylinder gasket G320RCy1016/007 Insulator gasket G320RCy1016/013 Crankcase gasket G320RC7332 Silencer gasket7337 Carburetor gasketUnit prices: 20,10 EURy1386/02 SCZ Sealing set for E290 race engineGenuine SCZ spare/option part.Set includes all necessary seals.
y1421 Versiown:
y1421/02 for Zenoah G320
Genuine HT spare/option part. The engine quick mount replaces the standard clutch housing. It allows a much faster installation or removal of the engine since the clutch side of the engine is only be clamped by one single screw. The gear plate remains in the vehicle, the motor flange on the engine.The engine quick mount fits all FG 2WD on-road cars with horizontal engine (except Formula 1) Sportsline, Competition and Evo (EVO model range till 2003, except Evo 2020 series).We are sorry, but due to the design the quick mount cannot be used for FG 1/6 off-road and monster cars.For the first time it is now possible to install the Zenoah G320 in these cars! For cars allready equipped with a FG quick mount only the engine flange y1423/02 is required.The quick mount is available in two versions:y1421/01 for all Zenoah and Chung Yang engines up to 30 cm³ with standard bolt pattern 50 x 36 mmy1421/02 for Zenoah G320When mounting the motor flange the bolts/nuts must be tightened together in small steps. To mount the studs from y1421/01 or the screws from y1421/02 the use of thread locking compound (link) is required.Please note: y1421/01 does not fit in combination with Zenoah OEM clutch!
y1467 Version:
y1467/01 Set with Allen head screws 10.9
Genuine Smartech spare/option part.Includes the complete set 26 body mounting washers, 22 support plates and corresponding screws for an original Losi 5ive-T or Losi 5ive-Mini body.Your choice of screws with either Allen head or hexalobular drive (a.k.a. Torx) heads!Content:26 pieces of mounting washers22 pieces of support plates14 pieces of countersunk screws (DIN7991) Allen head M4 x 20, 10.9 grade Alternatively TX10 Torx head, 10.9 grade12 pieces countersunk screws (DIN7991) Allen head M4 x 16, 10.9 gradeAlternatively TX10 Torx head, 10.9 grade
%
SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 24 mm hex wheel drive, 20 beadlock screws per rim and reinforced orangen beadlock rings. Fits Losi 5ive-T, 5ive Mini, Desert Buggy XL and all HPI Baja 5B and 5T/SC cars.Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.) On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks!MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part Some off-road tires knowledge can be found here!
SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 18 mm square or 24 mm hex wheel drive, 20 beadlock screws per rim and reinforced orange beadlock rings. Fits FG, Smartech, Losi 5ive-T, 5ive Mini, Desert Buggy XL and all HPI Baja 5B and 5T/SC cars.Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.) On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T and Super Baja Rey should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks!MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part Some off-road tires knowledge can be found here!
SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 24 mm hex wheel drive, 20 beadlock screws per rim and reinforced orange beadlock rings. Fits Losi 5ive-T, 5ive Mini, Desert Buggy XL and all HPI Baja 5B and 5T/SC cars.Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.) On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks!MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part Some off-road tires knowledge can be found here!
%
SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 18 mm square wheel drive, 20 beadlock screws per rim and reinforced beadlock rings. Fits FG, Smartech and many more models.Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.) On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPER GRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part Some off-road tires knowledge can be found here!