y1411 MadMax BIG DIGGER one pair front and one pair rear
Product information "y1411 MadMax BIG DIGGER one pair front and one pair rear"
Genuine MadMax spare/option part.
Losi and HPI foam tire inserts from can be used.
The BIG DIGGER tires had 84 extremely strong tread blocks on the front tires and 96 on the rears, with more than 1 cm² cross-section and 6 mm tread depth, allow for best power transfer and provide excellent grip even on loose surfaces like sand or soil.
Dimensions:
Contents:
Losi and HPI foam tire inserts from can be used.
The BIG DIGGER tires had 84 extremely strong tread blocks on the front tires and 96 on the rears, with more than 1 cm² cross-section and 6 mm tread depth, allow for best power transfer and provide excellent grip even on loose surfaces like sand or soil.
Dimensions:
- Outer diameter: 170 mm
- Tyre width front: 60 mm
- Tyre width rear: 80 mm
Contents:
- 4 pieces / 2 pairs
Some off-road tires knowledge can be found here!
Login
Customers also bought
OVER LANDER 170 x 80 mm and 170 x 60 mm tires with reinforced beadlock rings on black rims. The OVER LANDER were designed as all-terrain tires that can be used on virtually all surfaces because of its tightly attached lug tread pattern When a terrain includes sand, gravel and grass, the Overlander is the right choice! It can even be used on partially paved tracks!Of course, the OVER LANDER allround tire will not make special purpose tires like the TARMAC BUSTER,BIG DIGGER or CROSS BOND obsolete. Due to the extreme load created by the MadMax OVER LANDER tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars. We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel drive The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!
Hobbythek car bag for 1/5 carsFits for all 1/5 models for example: FG-: HPI-; Mecatech FW01-; Carson-; Smartech-; Conrads-; Harm-; RS5-; Lauterbacher a.s.oMade from extremely durable fabric, easily washable; with wrap-around shoulder belts and zipper closure.No dirt in the car boot!Dimensions:Length: 95 cmWidth: 40 cmHeight: 30 cm
Similar products
Genuine HPI spare/option part. Baja 5T/Rear - Losi 5ive-T Sand Buster-T Rib front and Sand Buster-T Paddle rear tires are now available from HPI Racing. These tires are designed specifically for the Baja 5T truck.Sand Busters-T Rib fronts have a rib down the center of the tire to cut through the sand for stable steering, and the Sand Buster-T Paddle rears have 10 large paddles for maximum traction in sand and soft dirt. Sand Buster's are designed for the sand, but you can also run them in loose dirt and even in the mud!Suitable for Losi 5ive-T as well (paddles all around).Contents:2 pieces / 1 pair
Genuine FG spare/option part. The sides of the Monster Truck tires were reinforced and now we deliver these tires without fabric insert. The advantages are a better lateral traction and more grip.diameter x width: 210 mm x 115 mmThe set includes two tires and two tire inserts.Contents:2 pieces
mammoth Rubber compound:
soft, y1160
Extra wide tire that fits 1/6 scale FG buggy/truck rims with extension ring!Diameter 165 mm, width 80 mm. Fits all FG and Carson largescale cars, may fit other cars with 18 mm wheel squares as well.HPI Baja 5 cars can also use these tires when equipped with special adapters.Available in three different compounds:mediumhard Prices are per pair (w/o inserts)We have tried various rubber / tire compounds for several months on various forms of terrain, etc.. The Mammoth brings, due to its quite strong and large pins and the extreme width of the tire, especially on hard and low grip surfaces a high traction! The Mammoth is available in soft, medium and hard! The rule is: the harder the ground the softer the tire compound. Where other tires spin helplessly the Mammoth provides serious traction. With few exceptions, the Mammoth is usually for the rear axle only. The disadvantage of Mammoth tires: Because of their extreme width they need to be mounted on FG wheels with extension rings and wide tire inserts (same as for the FG wide slicks), which is a labor intensive job. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall. From experience, we must strongly recommend against using rims from another manufacturer in combination with extension rings. Due to the before mentioned traction no other rim has been up to the task! Broken rims and torn squares were the result. However, the original FG-rim lasts without problems!
Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The BIG DIGGER tires had 84 extremely strong tread blocks on the front tires and 96 on the rears, with more than 1 cm² cross-section and 6 mm tread depth, allow for best power transfer and provide excellent grip even on loose surfaces like sand or soil. Dimensions:Outer diameter: 170 mmTyre width: 80 mmContents:2 pieces / 1 pair Some off-road tires knowledge can be found here!
Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The OVER LANDER MadMax are designed as all-terrain tires that can be used on virtually all surfaces because of its tightly attached lug tread pattern When a terrain includes sand, gravel and grass, the OVER LANDER is the right choice! It can even be used on partially paved tracks! Dimensions:Outer diameter: 170 mmTyre width: 80 mmContents:2 pieces / 1 pair Some off-road tires knowledge can be found here!
Genuine HPI spare/option part. Fits for Baja 5B/Front.Perfect for racing on rough and grassy surfaces, these front square block pattern tyres for the Baja are what every Baja racer has been begging for! Great in long and short grass conditions and designed by the HPI R&D team, you don't have to look any further for amazing front-end traction!Content:2 pieces / 1 pair
Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The OVER LANDER MadMax are designed as all-terrain tires that can be used on virtually all surfaces because of its tightly attached lug tread pattern When a terrain includes sand, gravel and grass, the OVER LANDER is the right choice! It can even be used on partially paved tracks! Dimensions:Outer diameter: 170 mmTyre width: 60 mmContents:2 pieces / 1 pair Some off-road tires knowledge can be found here!
Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The BIG DIGGER tires had 84 extremely strong tread blocks on the front tires and 96 on the rears, with more than 1 cm² cross-section and 6 mm tread depth, allow for best power transfer and provide excellent grip even on loose surfaces like sand or soil. Dimensions:Outer diameter: 170 mmTyre width: 60 mmContents:2 pieces / 1 pair Some off-road tires knowledge can be found here!
The sides of the Monster Truck tires were reinforced and now we deliver these tires without fabric insert. The advantages are a better lateral traction and more grip.diameter x width 210 x 115 mmThe set includes two tires and two tire inserts.
Genuine HPI spare/option part. Fits for Baja 5B/Front.Perfect for racing on rough and grassy surfaces, these front square block pattern tyres for the Baja are what every Baja racer has been begging for! Great in long and short grass conditions and designed by the HPI R&D team, you don't have to look any further for amazing front-end traction!Content:2 pieces / 1 pair
vpin Rubber compound:
y1234/01 - Soft
The V-pin competition tire is particularly suitable for tracks with loose and sandy surface. The high tread profile, extended to the tire shoulder requires a high manufacturing cost. This tread design guarantees an extremely high side traction and provides maximum propulsion especially on surfaces like sand and loose soil for optimum. A well proven combination is the use of in the rear and V-pin at the front. By cutting of the tread profile of the V-pin tires you can adjust your car's handling easily. The partly or nearly complete removal of the V-pin tire's tread on the outside of the tire, greatly affects the tire's side bite when cornering.Please take a look at the corresponding pics:Pic A - very high lateral grip = car tends to oversteerPic B - high lateral grip = still sharp steering responsePic C - reduced lateral grip = neutral handlingPic D - low lateral grip = expect the car to understeerOf course, the before mentioned does depend on the track surface!Summarized: removing tread from V-Pin tires on the front axle will reduce oversteering, calm your car and make it easier to drive.When oversteering is extreme (e.g. high grass) you may even start cutting the tread on the inside shoulder. This can prevent your car from those annoying traction rolls.For very loose soil the soft compound is recommended, under normal condition the medium compound is usually your best choice.HPI Baja 5 cars can also use these tires when equipped with special adapters. Dimensions:Diameter: 163 mmWidth: 65 mmInner diameter: 106 mm
Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The GIANT GRIP provides giant traction through 96 about one cm² wide and 5 mm high strong lugs, getting ample grip even on loose surfaces like sand and soil. Dimensions:Outer diameter: 190 mmTyre width: 70 mmContents:2 pieces / 1 pair Some off-road tires knowledge can be found here!
Customers also viewed
y1613 Version:
Front Medium und Heck Supersoft+ 60EUR
Genuine rc-car-online spare/option part.The optimal parking lot or race tires for your FG Racetruck model.Type Width Outer diameterFront 64 mm 153 mmRear 78 mm 153 mmGlued on original FG-Racetruck rims (rear tire with extension to the inside), incl. foam rubber insert,FG rim with 18 mm square drive and reinforcement ring.Attention: From experience we warn against using rims and extensions from another manufacturer.Since the Mammoth tires provide a very good grip, the rim and bonding are extremely stressed. Due to the high torque load in relation to the bonding of tires on large models, an occasional check in this regard and possibly a repair of the bonding (y0067) is inevitable.As a recommendation:The dirtier the track or the colder the temperature, the softer the rear tire should be.Reference for the front tire: With 2WD models this should be one to two stages harder than the used rear tire. On 4WD models, a tire combination with the same shore hardness front and rear is often good to drive.Of course, with Mammoth Supergrip Racetruck tires, the softer the tire, the higher the wear.The Mammoth Supergrip Racetruck tires have a special onroad tread. Whereby these still have an optimal grip after the wear of the tread, and can still be driven for a long time.
Variants from €89.90*
y1354 Version:
y1354/01 SPEED TEC Cross
Genuine Speed-Tec spare/option part. Due to the air boxes mandatory for racing and the required off-road air filters, a strong and rigid insulator is a must! No more stripped threads, no warpage and the resulting air leaks at the insulator anymore! So many weird running behaviors, for example if the engine is warmed up and a tiny gap occurred at the insulator, are caused by this distortion of a plastic insulator. The increased heat transfer of the aluminum is taken into account by addition of an insulator plate. Therefore the aluminum intake is largely insulated. Due to the face-milled surfaces of the aluminum intake you reach a greater durability of the gaskets. The SPEED TEC aluminum insulator is available with two insulator plates.y1354/01 SPEED TEC cross aluminum insulator with 7 mm insulator plate and therefore a longer intake path for more torque. Ideal for off-road and cars. y1354/02 SPEED TEC Race aluminum insulator with 4 mm insulator plate, better for maximum rpm and therefore best for on-road use! Dimensions: Height of aluminum intake 20 mmHeight of cross version insulator plate - 7mm Height of Race version insulator plate - 3 mm Contents:Aluminum intake insulator plate 3 x gasket 2 x allen screw 5 x 30 mm 2 x washer 5/9.8 mm
Glued on robust 6-spoke star wheels, with 6 ribbed reinforcement bars.With 18 mm wheel square, suitable for most 1:5 / 1:6 RC cars, FG, Carson, etc.Lane widening with 23 mm countersunk nut and 14 mm deep square drive for most models.450 block sections 3.5 mm thick, provide a good grip, even on hard or slippery surfaces.Due to the high-strength 14 mm tire shoulder, the cornering power of the Rallye-Cross 450 is high, despite the high profile of 3.5 mm, but without provoking a disproportionate overdrive of the model.The large inner diameter of 114 mm the rim, as well as the position of the wheel allows on nearly all models to eventually mount a disc brake at the front, as well as rear wheels. The dimension of the inside edge of the rim to the wheel is 20 mm. The 18 mm, 6-braced wheel square of the Rallye-Cross 450 rim is 8 mm deep.Measures of the Rallye-Cross 450 wheel/rim:Outside diameter: 162 mmProfile width: 62 mmRim inside: 114 mmTire shoulder: 14 mmBlock profile: 3,5 mmAlso suitable for:With the following wheel adapter: y1183 Rim adapterWith the following wheel adapter: y0786 Rim adapter
%
The Mercedes-AMG GT-3 is another model in the large GT-3 series on a TT-02 chassis. The original was used on the race tracks in the GT-3 class in 2016. It has a 6.3 litre V8 engine. This vehicle took 4th place in the 24-hour race at the Nürburgring. 4WD kit model, TT-02 chassis, electr. Speed controller, 540 torque
tuned motor, polycarbonate bodyshell
with add-on parts, cardan drive,
struts, independent suspension,
slick tyres, tub frame chassis,
instructions
Warnings:
Read and understand all instructions before starting assembly. If a child is assembling the model, a supervising adult should also have read the instructions. Tools including knives are used when assembling the kit. Special care should be taken to avoid injury. If difficulties arise during assembly, ask an adult to supervise the work or a modeller with RC experience or a specialist dealer.
Only use tools for their intended purpose. There is a risk of injury if used incorrectly. If you use paint and/or glue (not included in the kit), observe and follow the instructions supplied with the kit.
Keep the kit away from small children. Prevent children from putting any components in their mouths or pulling plastic bags over their heads. Caution! Not suitable for children under 14 years of age. Product details
Technical details: - 1:10 scale kit model - encapsulated 4WD all-wheel drive - prototypical, transparent Mercedes-Benz AMGGT-3 polycarbonate body - Powerful 540 electric motor- Independent front and rear suspension- New colour for the body: PS-63 Bright Gun metal(300086063). To achieve a matt finish, applyPS-55 must be sprayed onto the outside of the body. - Electronic speed control- Many optional tuning parts available
Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The OVER LANDER MadMax are designed as all-terrain tires that can be used on virtually all surfaces because of its tightly attached lug tread pattern When a terrain includes sand, gravel and grass, the OVER LANDER is the right choice! It can even be used on partially paved tracks! Dimensions:Outer diameter: 170 mmTyre width: 80 mmContents:2 pieces / 1 pair Some off-road tires knowledge can be found here!
Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The extremely rigid and differently structured lugs of the CROSS BOND ensure optimum power transmission and also allow for excellent grip on loose surfaces, such as sand and soil. The lugs are raised at the treads outside, and therefore provide maximum grip, particularly when cornering where the tire is canted to the outside.Dimensions:Outer diameter: 170 mmTyre width front: 60 mmTyre width rear: 80 mmContents:4 pieces / 2 pairs Some off-road tires knowledge can be found here!