MadMax SUPER GRIP Soft 170x80/x60 for FG, Smartech, HPI, Losi, Arrma & Co.
Product number:
y1463_02.1
EAN:
4058575148197
Product information "MadMax SUPER GRIP Soft 170x80/x60 for FG, Smartech, HPI, Losi, Arrma & Co. "
SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 18 mm square or 24 mm hex wheel drive, 20 beadlock screws per rim and reinforced orange beadlock rings. Fits FG, Smartech, Losi 5ive-T, 5ive Mini, Desert Buggy XL and all HPI Baja 5B and 5T/SC cars.
Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.
The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.
All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.
The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.)
On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T and Super Baja Rey should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the body shell.
The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.
The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks!
MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part
Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.
The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.
All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.
The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.)
On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T and Super Baja Rey should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the body shell.
The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.
The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks!
MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part
Some off-road tires knowledge can be found here!
Login
Accessories / Spare parts
Genuine HT spare/option part. Hardened special screws for mounting the beadlock rings of MadMax and Losi DBXL rims.For HPI rims due to the screw head diameter only to be used in combination with non-HPI beadlock rings (i.e. MadMax or Losi 5ive-T)!The combination of larger diameter and substantially larger thread depth ensures a secure grip of the screws in the plastic of the rims; the coarse thread also allows for quick assembly.The large head with T10 hexalobular drive distributes the load as wide as possible on the ring.The screws are galvanized for rust protection.Please note: it is not recommended to use the screws in rims which had previously M3 screws installed. With new rims or in exchange for M2.5 screws appropriate strength is ensured.Dimensions: Diameter: 3,1 mmLength: 12 mmHexalobular drive: T10 (Torx) Content:1 Set of 40 screws for one pair of rims.
Customers also viewed
If you want a special combination of compounds please enter that information into the "note to us" form field at the end of the checkout process.The widening ring on the rear rim is glued on the outside.Mammoth Supergrip for 1/6 and 1/5 offroad cars. Fits too for Formular 1 models!Parking lot / race tires for your offroad car.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmGlued on genuine FG silver rims (rear tires using extension rings), with foam rubber inserts included. Rim has 18 mm square drive with reinforcement ring.Please note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tirey0581y0582y0583y0584Rear tirey0591y0592y0593y0594General recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Prices per unit: FrontRearMammoth Supergrip:Pair44,90 EUR49,90 EURTire inserts:Pair13,00 EUR13,00 EURFG rim:Pair14,90 EUR14,90 EURFG extension ring:Pair--.-- EUR14,90 EURMounting:Pair13,00 EUR13,00 EURTotal Price 85,80 EUR 105,70 EUR = 191,50 EUR SETTotal for 1 pair each front and rear: 169,90 EUR================================Also suitable for:With the following wheel adapter: y1183 Rim adapter
SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 18 mm square or 24 mm hex wheel drive, 20 beadlock screws per rim and reinforced orange beadlock rings. Fits FG, Smartech, Losi 5ive-T, 5ive Mini, Desert Buggy XL and all HPI Baja 5B and 5T/SC cars.Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.) On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T and Super Baja Rey should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks!MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part Some off-road tires knowledge can be found here!
The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. - TT1040 Top Tuning wheel hub 24mm/6-edge for Losi Super BajaRey/2.0 and Super Rock Rey for plastic axle stubs. - AT-004 Atop wheel nuts 4 pieces Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.
y0580rg Tires:
Rear Hart, y0594+ 5EUR
Mammoth Supergrip complete gluedMammoth Supergrip for 1/6 and 1/5 offroad carsParking lot / race tires for your offroad car.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmGlued on genuine FG rims (rear tires using extension rings), with foam rubber inserts included. Rim has 18 mm square drive with reinforcement ring.Please note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tirey0581y0582y0583y0584Rear tirey0591y0592y0593y0594General recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Prices per unit: FrontRearMammoth Supergrip:Pair44,90 EUR49,90 EURTire inserts:Pair13,00 EUR13,00 EURFG rim:Pair14,90 EUR14,90 EURFG extension ring:Pair--.-- EUR14,90 EURMounting:Pair13,00 EUR13,00 EURPrices Total 85,80 EUR 105,70 EURAlso suitable for:With the following wheel adapter: y1183 Rim adapter
Variants from €69.90*
Glued on robust 6-spoke star wheels, with 6 ribbed reinforcement bars.With 18 mm wheel square, suitable for most 1:5 / 1:6 RC cars, FG, Carson, etc.Lane widening with 23 mm countersunk nut and 14 mm deep square drive for most models.450 block sections 3.5 mm thick, provide a good grip, even on hard or slippery surfaces.Due to the high-strength 14 mm tire shoulder, the cornering power of the Rallye-Cross 450 is high, despite the high profile of 3.5 mm, but without provoking a disproportionate overdrive of the model.The large inner diameter of 114 mm the rim, as well as the position of the wheel allows on nearly all models to eventually mount a disc brake at the front, as well as rear wheels. The dimension of the inside edge of the rim to the wheel is 20 mm. The 18 mm, 6-braced wheel square of the Rallye-Cross 450 rim is 8 mm deep.Measures of the Rallye-Cross 450 wheel/rim:Outside diameter: 162 mmProfile width: 62 mmRim inside: 114 mmTire shoulder: 14 mmBlock profile: 3,5 mmAlso suitable for:With the following wheel adapter: y1183 Rim adapterWith the following wheel adapter: y0786 Rim adapter
Offerset:1 Pair MadMax Supergrip front tires 170x60 mm1 Pair MadMax Supergrip rear tires 170x80 mm1 Pair MadMax front rims 60 mm1 Pair MadMax rear rims 80 mm1 Pair MadMax front inlays 60 mm1 Pair MadMax rear inlays 80 mm2 Pairs / 4 pieces adapter TT1020/01SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 24 mm hex wheel drive, 20 beadlock screws per rim and reinforced orange beadlock rings. Fits Losi 5ive-T, 5ive Mini, Desert Buggy XL and all HPI Baja 5B and 5T/SC cars.Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.The set consists of two each front and rear tires, including tire inserts and MadMax EXTREME rims and 4 pieces adapter wheel nuts TT1020/01.The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.) On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks!MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part Some off-road tires knowledge can be found here!TT1020 Top Tuning Adapter wheel nutGenuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces